Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Physics Conference Series

A Study of the HTS Josephson Junction Formed by a Ga Focused Ion Beam

K Hayashi, Teppei Ueda, Ryo Ohtani, Seiichiro Ariyoshi, Saburo Tanaka

Published Jul 1, 2020• 2 citations
Publisher

Abstract

Abstract High Temperature Superconductor Josephson Junctions (HTS-JJs) are based on artificial grain boundaries. However, the layout of HTS Superconducting QUantum Interference Devices (SQUIDs) on a bi-crystal substrate was restricted. Therefore, we considered to form low noise nano-bridge JJs by Ga Focused Ion Beam (Ga-FIB) irradiation. An 100 nm thick and 4 μm wide YBa2Cu3O7-δ (YBCO) micro-channels protected by a 20 nm thick Au protection layer were irradiated by line scans of Ga-FIB (Acceleration voltage: 40 kV, Beam diameter: ∼30 nm) and they were became normal conductivity except for the restricted region. In those nano-bridges, W N = 500 nm and fluence Φ = 2.0×1015 ions/cm2 of the nano-bridge was I C = 170 μA and we confirmed Shapiro steps by microwave irradiation of f RF = 2 GHz.

DOI
10.1088/1742-6596/1590/1/012044

Related papers

Fabrication of Ultrasmall High-Quality Bi2Sr2CaCu2O8+δIntrinsic Josephson Junctions

Tetsuro Matsumoto, Hiromi Kashiwaya, Hajime Shibata +3 more

The fabrication of ultrasmall high-quality intrinsic Josephson junctions (IJJs) using a cuprate superconductor is critical for the realization of a qubit. We investigated the mechanism of damage induced by a Ga + beam in a Bi 2 Sr 2 CaCu 2 O 8+δ IJJ during focused ion beam (FIB) processing. On the basis of the results, we developed a process that allowed the successful fabrication of an ultrasmall and high-quality IJJ. The damage induced by the FIB is reduced by restricting the direction of the Ga + beam so that the junction area is not directly irradiated by the ion beam. The fabricated ultrasmall IJJ device has a junction area of 0.3 µm 2 and shows excellent current–voltage characteristics.

Applied Physics Express•Sep 19, 2008•5 citations

YBa 2 Cu 3 O 7 nano superconducting quantum interference devices on MgO bicrystal substrates

Jianxin Lin, Benedikt Müller, Julian Linek +5 more

We report on nanopatterned YBa2Cu3O7-δ (YBCO) direct current superconducting quantum interference devices (SQUIDs) based on grain boundary Josephson junctions. The nanoSQUIDs are fabricated by epitaxial growth of 120 nm-thick films of the high-transition temperature cuprate superconductor YBCO via pulsed laser deposition on MgO bicrystal substrates with 24° misorientation angle, followed by sputtering of dAu = 65 nm thick Au. Nanopatterning is performed by Ga focused ion beam (FIB) milling. The SQUID performance is comparable to devices on SrTiO3 (STO), as demonstrated by electric transport and noise measurements at 4.2 K. MgO has orders of magnitude smaller dielectric permittivity than STO; i.e., one may avoid Au as a resistively shunting layer to reduce the intrinsic thermal flux noise of the nanoSQUIDs. However, we find that the Au layer is important for avoiding degradation during FIB milling. Hence, we compare devices with different dAu produced by thinning the Au layer via Ar ion milling after FIB patterning. We find that the reduction of dAu yields an increase in junction resistance, however at the expense of a reduction of the critical current and increase in SQUID inductance. This results in an estimated thermal flux noise that is almost independent of dAu. However, for two devices on MgO with 65 nm-thick Au, we find an order of magnitude lower low-frequency excess noise as compared to nanoSQUIDs on STO or those on MgO with reduced dAu. For one of those devices we obtain with bias-reversal readout ultra-low flux noise of ∼175 nΦ0 Hz-1/2 down to ∼10 Hz.

Nanoscale•Jan 1, 2020•16 citations

Investigation of Dayem Bridge NanoSQUIDs Made by Xe Focused Ion Beam

Tom Godfrey, John C. Gallop, David Cox +3 more

Superconducting QUantum Interference Devices (SQUIDs) based on nanobridge junctions have shown increasing promise for single particle detection. This paper describes the development of the fabrication of improved and reproducible nanobridge junctions fabricated by focused ion beam (FIB) milling from niobium thin films. Although the very low noise properties of nanobridge SQUIDs are well known, the nature of the milling process is little understood at the level of local superconducting properties. In this paper, we report the results for nanobridge Josephson devices and SQUIDs, which we believe are the first to be made by Xenon (Xe) FIB milling. Temperature-dependent current-voltage behavior, microwave-induced Shapiro steps, and SQUID response to magnetic fields have been measured. We make preliminary comparisons with nominally identical devices milled from Nb thin films using either Xe or Ga ions.

IEEE Transactions on Applied Superconductivity•Jul 19, 2018•7 citations

YBa$_2$Cu$_3$O$_7$ nano-constriction Josephson junctions and SQUIDs fabricated by focused helium-ion-beam irradiation

Christoph Schmid, Christopher Buckreus, David Haas +9 more

By focused $30\,\mathrm{keV}$ He ion beam irradiation, epitaxially grown YBa$_2$Cu$_3$O$_7$ (YBCO) thin films can be driven from the superconducting to the insulating state with increasing irradiation dose. A properly chosen dose suppresses superconductivity down to $4\,\mathrm{K}$, while crystallinity is still preserved. With this approach we create areas of normal-conducting YBCO that can be used to define resistively shunted constriction-type Josephson junctions (cJJs) on the nanometer scale. We also demonstrate that the fabricated cJJs can be incorporated in direct current superconducting quantum interference devices and can be used as detector junctions in THz antennas.

cond-mat.supr-conCross-listedarXiv:2511.19197•Nov 25, 2025•0 citations

YBa2Cu3O7− δ superconducting quantum interference devices with metallic to insulating barriers written with a focused helium ion beam

Ethan Y. Cho, M. K., Chuong Huynh +5 more

In this work, we demonstrate the ability to fabricate superconducting quantum interference devices (SQUIDs) by directly writing Josephson junctions into the plane of YBa2Cu3O7−δ thin films with a focused helium ion beam. This technique allows for the control of the Josephson barrier transport properties through the single parameter, ion dose. SQUIDs written with a dose of 4 × 1016 ions/cm2 had metallic barrier junctions that exhibited nearly ideal electrical transport characteristics at 50 K and a flux noise of 20 μΦ0/Hz at 10 Hz. At higher irradiation doses, the SQUIDs had insulating barrier Josephson junctions with a quasi particle energy gap edge at 20 meV.

Applied Physics Letters•Jun 22, 2015•69 citations

Zero-crossing Shapiro steps in focused-ion-beam-tailored high-$T_c$ superconducting microstructures

Myung‐Ho Bae, R. C. Dinsmore, Mitrabhanu Sahu +2 more

Microwave response of S-shaped Bi$_2$Sr$_2$CaCu2O$_{8+x}$ (Bi-2212) micron-scale samples, in which the supercurrent was forced to flow perpendicular to the crystal layers, was investigated. A treatment with a focused ion beam allowed us to reduce the plasma frequency down to $f_p$$\sim$5 GHz at $T$=0.3 K in naturally stacked Josephson junctions in a crystal. We observed Shapiro steps at frequencies as low as $\sim$5 GHz. Well-developed zero-crossing Shapiro steps were observed at frequencies as low as $\sim$10 GHz. They appeared as constant-voltage plateaus with a non-zero voltage occurring at zero bias current. We confirmed that zero-crossing Shapiro steps in the Bi-2212 stacked junctions can be observed when the irradiated frequency is sufficiently larger than $f_p$. The observed high-order fractional steps in the microwave responses indicate that the interlayer-coupled Bi-2212 Josephson junctions have nonsinusoidal current-phase relation. Based on the temperature dependence of the steps we also showed that the finite slope of the steps is due to the enhancement of the phase diffusion effect.

arXiv:0802.2091•Feb 14, 2008•0 citations
Abstract High Temperature Superconductor Josephson Junctions (HTS-JJs) are based on artificial grain boundaries. However, the layout of HTS Superconducting QUantum Interference Devices (SQUIDs) on a bi-crystal substrate was restricted. Therefore, we considered to form low noise nano-bridge JJs by Ga Focused Ion Beam (Ga-FIB) irradiation. An 100 nm thick and 4 μm wide YBa2Cu3O7-δ (YBCO) micro-channels protected by a 20 nm thick Au protection layer were irradiated by line scans of Ga-FIB (Acceleration voltage: 40 kV, Beam diameter: ∼30 nm) and they were became normal conductivity except for the restricted region. In those nano-bridges, W N = 500 nm and fluence Φ = 2.0×1015 ions/cm2 of the nano-bridge was I C = 170 μA and we confirmed Shapiro steps by microwave irradiation of f RF = 2 GHz.
The fabrication of ultrasmall high-quality intrinsic Josephson junctions (IJJs) using a cuprate superconductor is critical for the realization of a qubit. We investigated the mechanism of damage induced by a Ga + beam in a Bi 2 Sr 2 CaCu 2 O 8+δ IJJ during focused ion beam (FIB) processing. On the basis of the results, we developed a process that allowed the successful fabrication of an ultrasmall and high-quality IJJ. The damage induced by the FIB is reduced by restricting the direction of the Ga + beam so that the junction area is not directly irradiated by the ion beam. The fabricated ultrasmall IJJ device has a junction area of 0.3 µm 2 and shows excellent current–voltage characteristics.
We report on nanopatterned YBa2Cu3O7-δ (YBCO) direct current superconducting quantum interference devices (SQUIDs) based on grain boundary Josephson junctions. The nanoSQUIDs are fabricated by epitaxial growth of 120 nm-thick films of the high-transition temperature cuprate superconductor YBCO via pulsed laser deposition on MgO bicrystal substrates with 24° misorientation angle, followed by sputtering of dAu = 65 nm thick Au. Nanopatterning is performed by Ga focused ion beam (FIB) milling. The SQUID performance is comparable to devices on SrTiO3 (STO), as demonstrated by electric transport and noise measurements at 4.2 K. MgO has orders of magnitude smaller dielectric permittivity than STO; i.e., one may avoid Au as a resistively shunting layer to reduce the intrinsic thermal flux noise of the nanoSQUIDs. However, we find that the Au layer is important for avoiding degradation during FIB milling. Hence, we compare devices with different dAu produced by thinning the Au layer via Ar ion milling after FIB patterning. We find that the reduction of dAu yields an increase in junction resistance, however at the expense of a reduction of the critical current and increase in SQUID inductance. This results in an estimated thermal flux noise that is almost independent of dAu. However, for two devices on MgO with 65 nm-thick Au, we find an order of magnitude lower low-frequency excess noise as compared to nanoSQUIDs on STO or those on MgO with reduced dAu. For one of those devices we obtain with bias-reversal readout ultra-low flux noise of ∼175 nΦ0 Hz-1/2 down to ∼10 Hz.
Superconducting QUantum Interference Devices (SQUIDs) based on nanobridge junctions have shown increasing promise for single particle detection. This paper describes the development of the fabrication of improved and reproducible nanobridge junctions fabricated by focused ion beam (FIB) milling from niobium thin films. Although the very low noise properties of nanobridge SQUIDs are well known, the nature of the milling process is little understood at the level of local superconducting properties. In this paper, we report the results for nanobridge Josephson devices and SQUIDs, which we believe are the first to be made by Xenon (Xe) FIB milling. Temperature-dependent current-voltage behavior, microwave-induced Shapiro steps, and SQUID response to magnetic fields have been measured. We make preliminary comparisons with nominally identical devices milled from Nb thin films using either Xe or Ga ions.
YBa2_22​Cu3_33​O7_77​ nano-constriction Josephson junctions and SQUIDs fabricated by focused helium-ion-beam irradiation
By focused 30 keV30\,\mathrm{keV}30keV He ion beam irradiation, epitaxially grown YBa2_22​Cu3_33​O7_77​ (YBCO) thin films can be driven from the superconducting to the insulating state with increasing irradiation dose. A properly chosen dose suppresses superconductivity down to 4 K4\,\mathrm{K}4K, while crystallinity is still preserved. With this approach we create areas of normal-conducting YBCO that can be used to define resistively shunted constriction-type Josephson junctions (cJJs) on the nanometer scale. We also demonstrate that the fabricated cJJs can be incorporated in direct current superconducting quantum interference devices and can be used as detector junctions in THz antennas.
In this work, we demonstrate the ability to fabricate superconducting quantum interference devices (SQUIDs) by directly writing Josephson junctions into the plane of YBa2Cu3O7−δ thin films with a focused helium ion beam. This technique allows for the control of the Josephson barrier transport properties through the single parameter, ion dose. SQUIDs written with a dose of 4 × 1016 ions/cm2 had metallic barrier junctions that exhibited nearly ideal electrical transport characteristics at 50 K and a flux noise of 20 μΦ0/Hz at 10 Hz. At higher irradiation doses, the SQUIDs had insulating barrier Josephson junctions with a quasi particle energy gap edge at 20 meV.
Zero-crossing Shapiro steps in focused-ion-beam-tailored high-TcT_cTc​ superconducting microstructures
Microwave response of S-shaped Bi2_22​Sr2_22​CaCu2O8+x_{8+x}8+x​ (Bi-2212) micron-scale samples, in which the supercurrent was forced to flow perpendicular to the crystal layers, was investigated. A treatment with a focused ion beam allowed us to reduce the plasma frequency down to fpf_pfp​$\sim$5 GHz at TTT=0.3 K in naturally stacked Josephson junctions in a crystal. We observed Shapiro steps at frequencies as low as $\sim$5 GHz. Well-developed zero-crossing Shapiro steps were observed at frequencies as low as $\sim$10 GHz. They appeared as constant-voltage plateaus with a non-zero voltage occurring at zero bias current. We confirmed that zero-crossing Shapiro steps in the Bi-2212 stacked junctions can be observed when the irradiated frequency is sufficiently larger than fpf_pfp​. The observed high-order fractional steps in the microwave responses indicate that the interlayer-coupled Bi-2212 Josephson junctions have nonsinusoidal current-phase relation. Based on the temperature dependence of the steps we also showed that the finite slope of the steps is due to the enhancement of the phase diffusion effect.