Quantum computation promises to solve presently intractable problems, with hopes of yielding solutions to pressing issues to society. Despite this, current machines are limited to tens of qubits. The field is in a state of continuous scaling, with groups around the world working on all aspects of this problem. The work of this thesis aims to contribute to this effort. It is motivated by the goal of increasing both the speed and bandwidth of experiments conducted within our laboratory. Low-loss radio-frequency multiplexers were characterised at cryogenic temperatures, with some shown to operate at below 7mK. The Analog Devices ADG904 was one of these, and its insertion loss was measured at <0.5dB up to 2GHz. Their heat load was measured, and it was found that a switching speed of 10 MHz with an RF signal power of -30dB dissipates 43uW. Installing these switches yields a benefit over installing extra cabling in our cryostat for a switching speed of up to 2MHz and RF power of -30dBm. A switch matrix was prototyped for cryogenic operation, enabling re-routing of wiring inside a cryostat with a minimally increased thermal load. This could be used to significantly increase the scale of high frequency experiments. This switch has also been embedded within a calibration routine, facilitating measurement of a specific feature of interest at millikelvin temperatures. As the field of quantum engineering scales, such measurements will be crucial to close the loop, providing feedback to fabrication and semiconductor growth efforts. Finally, a rapid-turnaround test rig has been developed which has 32 high frequency and 100 DC lines, enabling tests of significant scale in liquid helium. This reduces the time per experiment at 4.2 K to hours rather than days, enabling tests such as thermal cycling, as well as the evaluation of on-chip structures or active electronics and classical computing hardware; which are all necessary elements of any solid state quantum computing architecture.
Quantum computation promises to solve presently intractable problems, with hopes of yielding solutions to pressing issues to society. Despite this, current machines are limited to tens of qubits. The field is in a state of continuous scaling, with groups around the world working on all aspects of this problem. The work of this thesis aims to contribute to this effort. It is motivated by the goal of increasing both the speed and bandwidth of experiments conducted within our laboratory. Low-loss radio-frequency multiplexers were characterised at cryogenic temperatures, with some shown to operate at below 7mK. The Analog Devices ADG904 was one of these, and its insertion loss was measured at <0.5dB up to 2GHz. Their heat load was measured, and it was found that a switching speed of 10 MHz with an RF signal power of -30dB dissipates 43uW. Installing these switches yields a benefit over installing extra cabling in our cryostat for a switching speed of up to 2MHz and RF power of -30dBm. A switch matrix was prototyped for cryogenic operation, enabling re-routing of wiring inside a cryostat with a minimally increased thermal load. This could be used to significantly increase the scale of high frequency experiments. This switch has also been embedded within a calibration routine, facilitating measurement of a specific feature of interest at millikelvin temperatures. As the field of quantum engineering scales, such measurements will be crucial to close the loop, providing feedback to fabrication and semiconductor growth efforts. Finally, a rapid-turnaround test rig has been developed which has 32 high frequency and 100 DC lines, enabling tests of significant scale in liquid helium. This reduces the time per experiment at 4.2 K to hours rather than days, enabling tests such as thermal cycling, as well as the evaluation of on-chip structures or active electronics and classical computing hardware; which are all necessary elements of any solid state quantum computing architecture.
Quantum entanglement and superposition, in addition to revealing interesting physics in their own right, can be harnessed as computational resources in a machine, enabling a range of algorithms for classically intractable problems. In recent years, experiments with small numbers of qubits have been demonstrated in a range of solid-state systems, but this is far from the numbers required to realise a useful quantum computer. In addition to the qubits themselves, quantum operation requires a host of classical electronics for control and readout, and current techniques used in few-qubit systems are not scalable. This thesis presents a series of techniques for control and readout of solid-state qubits, working towards scalability by integrating classical control with the quantum technology. Two techniques for reducing the footprint associated with readout of gallium arsenide spin qubits are demonstrated. Gate electrodes, used to define the quantum dot, are also shown to be sensitive state detectors. These gate-sensors, and the more conventional Quantum Point Contacts, are then multiplexed in the frequency domain, where three-channel qubit readout and ten-channel QPC readout are demonstrated. Two types of superconducting devices are also explored. The loss in superconducting coplanar waveguide resonators is measured, and a suppression of coupling to the parasitic electromagnetic environment is demonstrated. The thesis also details software for the simulation of Josephson-junction based circuits including features beyond what is available in commercial products. Finally, an architecture for managing control of a scalable machine is proposed where classical components are distributed throughout a cryostat and cryogenic switches route control pulses to the appropriate qubits. A simple implementation of the architecture is demonstrated that incorporates a double quantum dot, a gallium arsenide switch matrix, frequency multiplexed readout, and cryogenic classical computation.
Today's hundred-qubit quantum computers require a dramatic scale up to millions of qubits to become practical for solving real-world problems. Although a variety of qubit technologies have been demonstrated, scalability remains a major hurdle. Superconducting (SC) qubits are one of the most mature and promising technologies to overcome this challenge. However, these qubits reside in a millikelvin cryogenic dilution fridge, isolating them from thermal and electrical noise. They are controlled by a rack-full of external electronics through extremely complex wiring and cables. Although thousands of qubits can be fabricated on a single chip and cooled down to millikelvin temperatures, scaling up the control and readout electronics remains an elusive goal. This is mainly due to the limited available cooling power in cryogenic systems constraining the wiring capacity and cabling heat load management. In this article, we focus on scaling up the number of XY-control lines by using cryogenic RF-photonic links. This is one of the major roadblocks to build a thousand qubit superconducting QC. We will first review and study the challenges of state-of-the-art proposed approaches, including cryogenic CMOS and deep-cryogenic photonic methods, to scale up the control interface for SC qubit systems. We will discuss their limitations due to the active power dissipation and passive heat leakage in detail. By analytically modeling the noise sources and thermal budget limits, we will show that our solution can achieve a scale up to a thousand of qubits. Our proposed method can be seamlessly implemented using advanced silicon photonic processes, and the number of required optical fibers can be further reduced by using wavelength division multiplexing (WDM).
Quantum computation has been a major focus of research in the past two decades, with recent experiments demonstrating basic algorithms on small numbers of qubits. A large-scale universal quantum computer would have a profound impact on science and technology, providing a solution to several problems intractable for classical computers. To realise such a machine, today's small experiments must be scaled up, and a system must be built which provides control and measurement of many hundreds of qubits. A device of this scale is challenging: qubits are highly sensitive to their environment, and sophisticated isolation techniques are required to preserve the qubits' fragile states. Solid-state qubits require deep-cryogenic cooling to suppress thermal excitations. Yet current state-of-the-art experiments use room-temperature electronics which are electrically connected to the qubits. This thesis investigates various scalable technologies and techniques which can be used to control quantum systems. With the requirements for semiconductor spin-qubits in mind, several custom electronic systems, to provide quantum control from deep cryogenic temperatures, are designed and measured. A system architecture is proposed for quantum control, providing a scalable approach to executing quantum algorithms on a large number of qubits. Control of a gallium arsenide qubit is demonstrated using a cryogenically operated FPGA driving custom gallium arsenide switches. The cryogenic performance of a commercial FPGA is measured, as the main logic processor in a cryogenic quantum control system, and digital-to-analog converters are analysed during cryogenic operation. Recent work towards a 100-qubit cryogenic control system is shown, including the design of interconnect solutions and multiplexing circuitry. With qubit fidelity over the fault-tolerant threshold for certain error correcting codes, accompanying control platforms will play a key role in the development of a scalable quantum machine.
In recent years, quantum computers have emerged as a disruptive technology capable of solving problems currently intractable for classical systems. Computation is performed using qubits, which exploit quantum properties like superposition and entanglement, and requires them to operate at cryogenic temperatures. As a result, quantum computers are built around cryostats that reach temperatures as low as \qty{10}{\milli\kelvin}. However, to deliver a significant advantage over conventional approaches, quantum computers must increase their qubit count, improve qubit quality, and adopt more sophisticated control and readout architectures. The integration of more complex or improved cryogenic electronics inside the cryostat can enhance the scalability of these systems, and is the topic of this thesis. The primary technology platform used in this work is based on cryogenic InGaAs/InP high-electron-mobility transistors (HEMTs). One objective was the development of cryogenic circuits that enhance the scalability of spin-qubit quantum computers by enabling efficient signal delivery in control and readout paths. To this end, cryogenic multiplexers were demonstrated with threshold voltages as low as \qty{90}{\milli\volt}, subthreshold swing of \qty{5}{\milli\volt\per dec}, and on-off ratio of 107 at \qty{4}{\kelvin}. In addition, a charge-storage array was developed for the local generation of qubit bias signals, using an operation scheme based on pulse trains to program voltage levels on capacitors that can be placed in proximity to qubit gates. A second objective was the fabrication of HEMTs with enhanced performance for use in cryogenic low-noise amplifiers, which are critical for qubit readout. Studies were performed to characterize self-heating, an effect that limits transistor performance at cryogenic temperatures. Moreover HEMTs with improved characteristics were fabricated, which achieved exceptional values in state-of-the-art metrics, including fT= \qty{622}{\giga\hertz}, fMAX= \qty{733}{\giga\hertz}, and a noise indication factor IDS/gm= \qty{0.17}{\sqrt{\volt \cdot \milli\meter / \siemens}} at \qty{4}{\kelvin}. These results represent a new record for the combination of high-frequency and low-noise performance in a cryogenic HEMT. These results establish the InGaAs/InP HEMT technology as a promising platform for the development of cryogenic circuits, and demonstrate its versatility in addressing multiple applications requiring both single-device performance and integration at the circuit level.
The transition of quantum technologies from laboratory-scale demonstrations to fault-tolerant and deployable systems is increasingly limited by the classical–quantum hardware interface. Although microwave subsystems for several leading quantum-computing platforms have been reviewed previously, the RF-to-terahertz hardware requirements that enable cross-platform maturation remain less systematically addressed. This article critically reviews RF-to-terahertz hardware for quantum technologies, focusing on cryogenic integration, high-density interconnects, and fabrication bottlenecks. Recent experimental efforts from the electronics engineering community are analyzed to identify shared limitations in low-temperature device modeling, thermal management, signal integrity, low-noise amplification, passive microwave structures, control and readout electronics, microwave-to-optical transduction, and scalable packaging. Competing approaches are assessed against common engineering criteria including RF and noise performance, bandwidth, power dissipation and thermal load, integration density, calibration complexity, fabrication reproducibility, and maturity toward scalable deployment. The review argues that future progress is no longer governed only by the optimization of individual components, but by the co-design of materials, devices, interconnects, control architectures, measurement chains, and manufacturing processes. In this framework, scalability, miniaturization, integration density, and reproducibility become central metrics for quantum hardware development. By synthesizing developments across quantum computing, sensing, communication, and networking platforms, this review provides a component-level roadmap for RF, microwave, terahertz, and electronics engineers working toward scalable, manufacturable, and interoperable quantum technology systems.
Quantum computing promises an exponential speed-up of computation compared to what is nowadays achievable with classical computers. In this way, it enables the evaluation of more complex models and the breaching of current security algorithms. For the operation of a quantum system, many questions remain to be answered. Currently, there are several quantum technologies that promise to be both reliable and scalable, two features required for large scale quantum operations. Common to all technologies is the operating temperature that needs to be close to absolute zero, i.e. below 100 mK, to suppress environment noise and allow the quantum properties to become 'visible'. In order for any quantum processor to be operated, a so-called quantum-classical interface is required for the quantum bit (qubit) read-out and control. This interface consists of various electronic blocks, such as analog-to-digital converters, digital-to-analog converters, mixers, amplifiers and a digital controller. Especially the analog blocks require effort to meet the noise and stability constraints as not to disturb the very sensitive qubits and allow reading of the tiny signals. As the qubits live in extremely deep-cryogenic temperatures, long wires interface the cryogenic with the room temperature environment, where most of the electronics is situated. However, for a scalable system, heat injection becomes a serious problem, with many wires between 300 K and sub-Kelvin. Furthermore, such amount of interconnects is challenging to mechanically place in a dilution refrigerator. Therefore, in this work, we propose to implement the electronics not at room temperature, but at a temperature much closer to the qubits, for example at 4 K. This not only reduces significantly the wiring between room temperature and the qubits, but we can also benefit from lower electronic noise at such a temperature. The operation of conventional electronics almost 200°C below its normal temperature range is not trivial as device properties alter significantly and most circuits no longer operate as intended. In CMOS processes, the main technology in the integrated electronics world, the behaviour of the transistors, required for the implementation of any circuit, deviates considerably at low temperatures. The transistor's threshold voltage goes up, the mobility increases and the subthreshold slope becomes steeper, to name just a few of these deviations. Although there are improvements in performance, there are also some counter effects, and characterization of the transistors is needed to observe the changes. Once devices are characterized at such low temperatures, new models can be built and circuits can be simulated and adapted to operate properly at cryogenic temperatures. Luckily, there are various commercially available devices that can already withstand the chills of cold. We demonstrated various commercially available devices, such as a field-programmable gate array (FPGA) implemented in a 28 nm CMOS process, to be operating without major concerns at 4~K. Its properties alter only slightly, within 5 to 10%, and all tested circuit implementations, working at 300~K, also worked at 4 K. We combined both commercially available devices, that operate 200 K below their specified temperature range, with custom designed CMOS circuits to implement a cryogenic read-out platform for spin qubits. This system comprises amplifiers, an ADC, an FPGA, voltage regulators and a clock generator. It allows to amplify the tiny signal from the qubits and digitize it directly in the FPGA in order to process the data locally at 4~K. This system is one of the first systematic attempts at operating a part of the quantum-classical interface at cryogenic temperatures and forms the basis for future systems comprising the complete electronic interface for qubits to operate at such low temperatures. One of the main problems to tackle for cryogenic electronic systems is their power consumption. Power budgets are simply limited to roughly 1 or 2 Watts at 4 K and exponentially lower at deeper cryogenic temperatures, thus limiting the size of large-scale electronic systems. Our approach of combined commercial and custom circuits will have to be steadily replaced by a single (custom) technology that meets both power and scalability constraints. One of the best candidates is CMOS, a technology that the industry has relied upon for several decades and benefits from many optimizations thanks to Moore's law.