Today's hundred-qubit quantum computers require a dramatic scale up to millions of qubits to become practical for solving real-world problems. Although a variety of qubit technologies have been demonstrated, scalability remains a major hurdle. Superconducting (SC) qubits are one of the most mature and promising technologies to overcome this challenge. However, these qubits reside in a millikelvin cryogenic dilution fridge, isolating them from thermal and electrical noise. They are controlled by a rack-full of external electronics through extremely complex wiring and cables. Although thousands of qubits can be fabricated on a single chip and cooled down to millikelvin temperatures, scaling up the control and readout electronics remains an elusive goal. This is mainly due to the limited available cooling power in cryogenic systems constraining the wiring capacity and cabling heat load management. In this article, we focus on scaling up the number of XY-control lines by using cryogenic RF-photonic links. This is one of the major roadblocks to build a thousand qubit superconducting QC. We will first review and study the challenges of state-of-the-art proposed approaches, including cryogenic CMOS and deep-cryogenic photonic methods, to scale up the control interface for SC qubit systems. We will discuss their limitations due to the active power dissipation and passive heat leakage in detail. By analytically modeling the noise sources and thermal budget limits, we will show that our solution can achieve a scale up to a thousand of qubits. Our proposed method can be seamlessly implemented using advanced silicon photonic processes, and the number of required optical fibers can be further reduced by using wavelength division multiplexing (WDM).
Today's hundred-qubit quantum computers require a dramatic scale up to millions of qubits to become practical for solving real-world problems. Although a variety of qubit technologies have been demonstrated, scalability remains a major hurdle. Superconducting (SC) qubits are one of the most mature and promising technologies to overcome this challenge. However, these qubits reside in a millikelvin cryogenic dilution fridge, isolating them from thermal and electrical noise. They are controlled by a rack-full of external electronics through extremely complex wiring and cables. Although thousands of qubits can be fabricated on a single chip and cooled down to millikelvin temperatures, scaling up the control and readout electronics remains an elusive goal. This is mainly due to the limited available cooling power in cryogenic systems constraining the wiring capacity and cabling heat load management. In this article, we focus on scaling up the number of XY-control lines by using cryogenic RF-photonic links. This is one of the major roadblocks to build a thousand qubit superconducting QC. We will first review and study the challenges of state-of-the-art proposed approaches, including cryogenic CMOS and deep-cryogenic photonic methods, to scale up the control interface for SC qubit systems. We will discuss their limitations due to the active power dissipation and passive heat leakage in detail. By analytically modeling the noise sources and thermal budget limits, we will show that our solution can achieve a scale up to a thousand of qubits. Our proposed method can be seamlessly implemented using advanced silicon photonic processes, and the number of required optical fibers can be further reduced by using wavelength division multiplexing (WDM).
Quantum computing promises an exponentially higher computational power than classical computers; although all the building blocks have become available, certain constraints still prevent quantum advantage. The fundamental challenge in building a practical quantum computer is integrating thousands of highly coherent qubits with the control and readout electronics. The need for a high‐coherence qubit drives the effort for quantum error correction algorithms to create fault‐tolerant quantum systems. Error correction becomes tangible in a quantum processor only in large numbers of qubits. Thus, the other challenge is reducing the number of physical interconnects (coaxial lines) between the quantum–classical interface and bulky room‐temperature electronics. To interface thousands of qubits, interconnects can be reduced by bringing the control and readout electronics near the quantum processor. Cryogenic complementary metal–oxide–semiconductor (CMOS) technology has been an ideal candidate for this purpose. Integrated control and readout at cryogenic temperatures require low power dissipation circuit designs and techniques such as frequency‐division multiplexing (FDM) due to the finite cooling power of a dilution refrigerator. Herein, an overview of each building block in a superconducting quantum computer is provided, focusing on scalability. Furthermore, this article is concluded with an outlook discussing current challenges and future directions for the scalable superconducting control and readout.
Current control techniques for cryogenically cooled qubits are realized with coaxial cables, posing multiple challenges in terms of cost, thermal load, size, and long-term scalability. Emerging approaches to tackle this issue include cryogenic CMOS electronics at 4 K, and photonic links for direct qubit control. In this paper, we propose a multiplexed all-passive cryogenic high frequency direct detection control platform (cryo HFDD). The proposed classical interface for direct qubit control utilizes optical or sub-THz bands. We present the possible tradeoffs of this platform, and compare it with current state of-the-art cryogenic CMOS and conventional coaxial approaches. Weassess the feasibility of adopting these efficient links for a wide range of microwave qubit power levels. Specifically, we estimate the heat load to achieve the required signal-to-noise ratio SNR considering different noise sources, component losses, as well as link density. We show that multiplexed photonic receivers at 4 K can aggressively scale the control of thousands of qubits. This opens the door for low cost scalable quantum computing systems.
Large-scale cryogenic quantum systems are constrained by an input-output bottleneck between room-temperature electronics and millikelvin stages, particularly in superconducting qubit platforms. This bottleneck is most acute for output lines, where bulky and expensive microwave components limit scalability. A promising approach for scalable characterization and testing is to perform signal multiplexing directly at the qubit plane. We demonstrate a cryogenic CMOS (cryoCMOS) RF multiplexer operating at 10 millikelvin with record-low static power consumption of 200 pW. The device provides < 2 dB insertion loss and > 30 dB isolation across DC-8 GHz. Direct connection to transmon qubits marginally affects coherence times in the range of 100 microseconds, enabling multiplexing of readout, flux and, in principle, XY drive lines. This work introduces cryoCMOS multiplexers as valuable tools for scalable, high-throughput cryogenic characterization and testing, and advances co-integrated quantum-classical control for future large-scale quantum processors.
Abstract Large-scale superconducting quantum computing systems entail high-fidelity control and readout of large numbers of qubits at millikelvin temperatures, resulting in a massive input-output bottleneck. Cryo-electronics, based on complementary metal-oxide-semiconductor (CMOS) technology, may offer a scalable and versatile solution to overcome this bottleneck. However, detrimental effects due to cross-coupling between the electronic and thermal noise generated during cryo-electronics operation and the qubits need to be avoided. Here we present an ultra-low power radio-frequency (RF) multiplexing cryo-electronics solution operating below 15 mK that allows for control and interfacing of superconducting qubits with minimal cross-coupling. We benchmark its performance by interfacing it with a superconducting qubit and observe that the qubit’s relaxation times (T1) are unaffected, while the coherence times (T2) are only minimally affected in both static and dynamic operation. Using the multiplexer, single qubit gate fidelities above 99.9%, i.e., well above the threshold for surface-code based quantum error-correction, can be achieved with appropriate thermal filtering. In addition, we demonstrate the capability of time-division-multiplexed qubit control by dynamically windowing calibrated qubit control pulses. Our results show that cryo-CMOS multiplexers could be used to significantly reduce the wiring resources for large-scale qubit device characterization, large-scale quantum processor control and quantum error correction protocols.
Quantum computers can provide exponential speedup in solving certain computational problems pertaining to drug discovery, cybersecurity, weather forecasting, etc. Although a quantum computer with just 50-qubits has been shown to surpass the computing power of the best supercomputers in specific applications, millions of qubits would be required for useful practical applications. One of the biggest obstacles in scaling from 50 qubits to millions of qubits is the interconnect bottleneck between solid-state qubits operating at 20 milliKelvin inside a dilution refrigerator and control electronics outside the dilution refrigerator connected via long coaxial cables. A 50-qubit processor requires hundreds of cables, digital to analog converters, mixers and amplifiers, clearly challenging the scalability of the system. The goal of this research is to build scalable quantum computers by operating CMOS control electronics inside the dilution refrigerator in proximity to quantum processors. The dissertation covers a broad aspect of cryogenic integrated circuit design spanning across devices, circuits and systems.
Scaling superconducting quantum computers toward thousands of control channels remains a difficult hardware problem. This requires reducing room-temperature-to-cryogenic interconnects and 4 K power while retaining channel-specific programmability. We develop a hybrid photonic/CMOS control architecture in which optical fibers distribute shared Gaussian and derivative pulse templates, while local cryogenic CMOS circuits provide event-rate amplitude programming, pulse blocking, hold-duration control, photodetection, and microwave upconversion. The architecture supports template-based XY/DRAG control and smooth-edged flat-top envelopes for two-qubit control through separate local signal paths. Compared with full-waveform Cryo-CMOS, it moves high-speed sampled-waveform generation out of each cryogenic channel. Compared with per-channel photonic waveform delivery, it retains a programmable endpoint after optical distribution for applying updated channel coefficients and control states. We evaluate the architecture using post-layout circuit simulations, optical and interconnect models, and system-level power scaling under a common 4 K output boundary. The modeled downlink power is below 1 mW per qubit-control channel at the thousand-channel scale, substantially below the normalized full-waveform Cryo-CMOS result and in the same range as the strict 50-ohm direct-detection WDM reference. Simulated I- and Q-path outputs are propagated through a five-level transmon model, while the simulated sample-and-hold output is evaluated in a coupled-transmon model. The tested single-qubit cases remain below the 10^-3 worst-state error reference, and the representative two-qubit result remains near the same scale after model-level calibration. These results support low-power photonic delivery with limited in-fridge programmability for template-compatible superconducting-qubit control.