Quantum computation has been a major focus of research in the past two decades, with recent experiments demonstrating basic algorithms on small numbers of qubits. A large-scale universal quantum computer would have a profound impact on science and technology, providing a solution to several problems intractable for classical computers. To realise such a machine, today's small experiments must be scaled up, and a system must be built which provides control and measurement of many hundreds of qubits. A device of this scale is challenging: qubits are highly sensitive to their environment, and sophisticated isolation techniques are required to preserve the qubits' fragile states. Solid-state qubits require deep-cryogenic cooling to suppress thermal excitations. Yet current state-of-the-art experiments use room-temperature electronics which are electrically connected to the qubits. This thesis investigates various scalable technologies and techniques which can be used to control quantum systems. With the requirements for semiconductor spin-qubits in mind, several custom electronic systems, to provide quantum control from deep cryogenic temperatures, are designed and measured. A system architecture is proposed for quantum control, providing a scalable approach to executing quantum algorithms on a large number of qubits. Control of a gallium arsenide qubit is demonstrated using a cryogenically operated FPGA driving custom gallium arsenide switches. The cryogenic performance of a commercial FPGA is measured, as the main logic processor in a cryogenic quantum control system, and digital-to-analog converters are analysed during cryogenic operation. Recent work towards a 100-qubit cryogenic control system is shown, including the design of interconnect solutions and multiplexing circuitry. With qubit fidelity over the fault-tolerant threshold for certain error correcting codes, accompanying control platforms will play a key role in the development of a scalable quantum machine.
Quantum computation has been a major focus of research in the past two decades, with recent experiments demonstrating basic algorithms on small numbers of qubits. A large-scale universal quantum computer would have a profound impact on science and technology, providing a solution to several problems intractable for classical computers. To realise such a machine, today's small experiments must be scaled up, and a system must be built which provides control and measurement of many hundreds of qubits. A device of this scale is challenging: qubits are highly sensitive to their environment, and sophisticated isolation techniques are required to preserve the qubits' fragile states. Solid-state qubits require deep-cryogenic cooling to suppress thermal excitations. Yet current state-of-the-art experiments use room-temperature electronics which are electrically connected to the qubits. This thesis investigates various scalable technologies and techniques which can be used to control quantum systems. With the requirements for semiconductor spin-qubits in mind, several custom electronic systems, to provide quantum control from deep cryogenic temperatures, are designed and measured. A system architecture is proposed for quantum control, providing a scalable approach to executing quantum algorithms on a large number of qubits. Control of a gallium arsenide qubit is demonstrated using a cryogenically operated FPGA driving custom gallium arsenide switches. The cryogenic performance of a commercial FPGA is measured, as the main logic processor in a cryogenic quantum control system, and digital-to-analog converters are analysed during cryogenic operation. Recent work towards a 100-qubit cryogenic control system is shown, including the design of interconnect solutions and multiplexing circuitry. With qubit fidelity over the fault-tolerant threshold for certain error correcting codes, accompanying control platforms will play a key role in the development of a scalable quantum machine.
Quantum entanglement and superposition, in addition to revealing interesting physics in their own right, can be harnessed as computational resources in a machine, enabling a range of algorithms for classically intractable problems. In recent years, experiments with small numbers of qubits have been demonstrated in a range of solid-state systems, but this is far from the numbers required to realise a useful quantum computer. In addition to the qubits themselves, quantum operation requires a host of classical electronics for control and readout, and current techniques used in few-qubit systems are not scalable. This thesis presents a series of techniques for control and readout of solid-state qubits, working towards scalability by integrating classical control with the quantum technology. Two techniques for reducing the footprint associated with readout of gallium arsenide spin qubits are demonstrated. Gate electrodes, used to define the quantum dot, are also shown to be sensitive state detectors. These gate-sensors, and the more conventional Quantum Point Contacts, are then multiplexed in the frequency domain, where three-channel qubit readout and ten-channel QPC readout are demonstrated. Two types of superconducting devices are also explored. The loss in superconducting coplanar waveguide resonators is measured, and a suppression of coupling to the parasitic electromagnetic environment is demonstrated. The thesis also details software for the simulation of Josephson-junction based circuits including features beyond what is available in commercial products. Finally, an architecture for managing control of a scalable machine is proposed where classical components are distributed throughout a cryostat and cryogenic switches route control pulses to the appropriate qubits. A simple implementation of the architecture is demonstrated that incorporates a double quantum dot, a gallium arsenide switch matrix, frequency multiplexed readout, and cryogenic classical computation.
Quantum computing promises an exponential speed-up of computation compared to what is nowadays achievable with classical computers. In this way, it enables the evaluation of more complex models and the breaching of current security algorithms. For the operation of a quantum system, many questions remain to be answered. Currently, there are several quantum technologies that promise to be both reliable and scalable, two features required for large scale quantum operations. Common to all technologies is the operating temperature that needs to be close to absolute zero, i.e. below 100 mK, to suppress environment noise and allow the quantum properties to become 'visible'. In order for any quantum processor to be operated, a so-called quantum-classical interface is required for the quantum bit (qubit) read-out and control. This interface consists of various electronic blocks, such as analog-to-digital converters, digital-to-analog converters, mixers, amplifiers and a digital controller. Especially the analog blocks require effort to meet the noise and stability constraints as not to disturb the very sensitive qubits and allow reading of the tiny signals. As the qubits live in extremely deep-cryogenic temperatures, long wires interface the cryogenic with the room temperature environment, where most of the electronics is situated. However, for a scalable system, heat injection becomes a serious problem, with many wires between 300 K and sub-Kelvin. Furthermore, such amount of interconnects is challenging to mechanically place in a dilution refrigerator. Therefore, in this work, we propose to implement the electronics not at room temperature, but at a temperature much closer to the qubits, for example at 4 K. This not only reduces significantly the wiring between room temperature and the qubits, but we can also benefit from lower electronic noise at such a temperature. The operation of conventional electronics almost 200°C below its normal temperature range is not trivial as device properties alter significantly and most circuits no longer operate as intended. In CMOS processes, the main technology in the integrated electronics world, the behaviour of the transistors, required for the implementation of any circuit, deviates considerably at low temperatures. The transistor's threshold voltage goes up, the mobility increases and the subthreshold slope becomes steeper, to name just a few of these deviations. Although there are improvements in performance, there are also some counter effects, and characterization of the transistors is needed to observe the changes. Once devices are characterized at such low temperatures, new models can be built and circuits can be simulated and adapted to operate properly at cryogenic temperatures. Luckily, there are various commercially available devices that can already withstand the chills of cold. We demonstrated various commercially available devices, such as a field-programmable gate array (FPGA) implemented in a 28 nm CMOS process, to be operating without major concerns at 4~K. Its properties alter only slightly, within 5 to 10%, and all tested circuit implementations, working at 300~K, also worked at 4 K. We combined both commercially available devices, that operate 200 K below their specified temperature range, with custom designed CMOS circuits to implement a cryogenic read-out platform for spin qubits. This system comprises amplifiers, an ADC, an FPGA, voltage regulators and a clock generator. It allows to amplify the tiny signal from the qubits and digitize it directly in the FPGA in order to process the data locally at 4~K. This system is one of the first systematic attempts at operating a part of the quantum-classical interface at cryogenic temperatures and forms the basis for future systems comprising the complete electronic interface for qubits to operate at such low temperatures. One of the main problems to tackle for cryogenic electronic systems is their power consumption. Power budgets are simply limited to roughly 1 or 2 Watts at 4 K and exponentially lower at deeper cryogenic temperatures, thus limiting the size of large-scale electronic systems. Our approach of combined commercial and custom circuits will have to be steadily replaced by a single (custom) technology that meets both power and scalability constraints. One of the best candidates is CMOS, a technology that the industry has relied upon for several decades and benefits from many optimizations thanks to Moore's law.
Recent advances in solid-state qubit technology are paving the way to fault-tolerant quantum computing systems. However, qubit technology is limited by qubit coherence time and the scaling of quantum processors is limited by the complexity of coupling quantum systems with a classical electronic infrastructure. Hence, the proposed approach is to use CMOS at cryogenic temperatures, in order to ensure physical proximity to the quantum bits, thus reducing thermal gradients and increasing compactness. In this thesis, several RF circuits designed using commercial CMOS technology have been shown to be working at cryogenic temperatures. Such circuits could be easily interfaced (or integrated, in the future) with a qubit processor. The performance of the circuits is comparable to the state-of-the-art systems, currently used as control units for qubits. Moreover, these circuits have a much smaller form factor and could be made to work inside a dilution refrigerator where the qubits are operational, hence providing the first demonstration of a scalable solution.
Quantum computers can provide exponential speedup in solving certain computational problems pertaining to drug discovery, cybersecurity, weather forecasting, etc. Although a quantum computer with just 50-qubits has been shown to surpass the computing power of the best supercomputers in specific applications, millions of qubits would be required for useful practical applications. One of the biggest obstacles in scaling from 50 qubits to millions of qubits is the interconnect bottleneck between solid-state qubits operating at 20 milliKelvin inside a dilution refrigerator and control electronics outside the dilution refrigerator connected via long coaxial cables. A 50-qubit processor requires hundreds of cables, digital to analog converters, mixers and amplifiers, clearly challenging the scalability of the system. The goal of this research is to build scalable quantum computers by operating CMOS control electronics inside the dilution refrigerator in proximity to quantum processors. The dissertation covers a broad aspect of cryogenic integrated circuit design spanning across devices, circuits and systems.
Quantum computers have gained widespread interest as they can potentially solve problems that are intractable even for today’s supercomputers, such as the simulation of quantum systems as initially proposed by Feynman. To achieve such tremendous progress, a quantum computer relies on processing the information stored in quantum bits (qubits), the fundamental units of quantum computation, similar to the bits in a classical (i.e., non-quantum) processor. In general, a quantum processor comprising several qubits is connected through a quantum-to-classical interface consisting of classical electrical circuits for manipulating and reading out their quantum state. The accuracy of an operation on a qubit is characterized using the fidelity, which is 100 % in case of a perfect operation. In practice, a fidelity between 99 % and 99.9 % is typically achieved in today’s experiments with less than 100 qubits, limited by non-idealities in the control signals and by the implementation of the physical qubit itself. Since such qubit fidelities are too low to execute relevant quantum algorithms, quantum error correction schemes have been developed which rely on a much larger number of qubits to correct for possible errors, resulting in the need for quantum processors with thousands or millions of qubits. Solid-state qubits promise the largescale integration required to scale to millions of qubits, as they exploit the lithographic fabrication techniques borrowed from the semiconductor industry. However, state-of-theart solid-state qubits, such as transmons and single-electron spin qubits, must be typically cooled to cryogenic temperatures in a dilution refrigerator to exhibit quantum behavior. Because of the limited number of qubits (< 100) in state-of-theart solid-state quantum processors, the classical controller is currently implemented by general-purpose instruments or by tailor-made controllers operating at room temperature connected via several wires to the qubits in the cryogenic chamber. However, these systems must scale to support millions of qubits. While scaling up the underlying quantum processor is already exceptionally challenging, building the electronics required to interface such a large-scale processor is just as relevant and arduous.
A fault tolerant scalable quantum computer requires more than 1000 Qubits to perform real time state correction and to improve the Qubit coherence time. The dense wiring connections required between the quantum processor placed at a 100 mK temperature and the room temperature control and readout electronics serve as a limiting factor in this system. Qubit control and readout electronics operating at 4 K temperature, placed closer to a quantum processor inside the dilution refrigerator avoids the dense wiring connections to room temperature electronics, and hence, serve as a potential solution to realize a scalable quantum computer. However, with no CMOS process technology models available at cryogenic temperatures, the design of a fully integrated, ultra-low power Qubit control and readout electronics at a sub-1 mW power consumption proves to be extremely challenging. In recent years, there has been a huge rise in interest among the research communities to understand and solve the device and circuit level challenges at deep cryogenic temperatures. This paper presents an overview of the recently published active and passive device nonidealities, circuit design challenges and solutions, and the future research directions in the Qubit control and readout electronics operating at deep cryogenic temperatures.