Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

4-bit Bit-Slice Arithmetic Logic Unit for 32-bit RSFQ Microprocessors

Guang-Ming Tang, Takata Kensuke, Masamitsu Tanaka, Akira Fujimaki, Kazuyoshi Takagi, Naofumi Takagi

Published Dec 10, 2015• 64 citations
Publisher

Abstract

A 4-bit bit-slice arithmetic logic unit (ALU) for 32-bit rapid single-flux-quantum microprocessors was demonstrated. The proposed ALU covers all of the ALU operations for the MIPS32 instruction set. It processes bit-sliced 32-bit data that are divided into eight slices of 4 bits. The bit-slice approach simplifies the circuit structure and reduces the hardware cost. The ALU uses synchronous concurrent-flow clocking and consists of eight pipeline stages. It was implemented using the 1.0-μm Nb/AlOx/Nb nine-layer advanced process 2 (ADP2) with a critical current density of 10 kA/cm2, and fabricated by National Institute of Advanced Industrial Science and Technology (AIST). It consists of 3481 Josephson junctions with an area of 3.09 × 1.66 mm2. It achieved the target frequency of 50 GHz and a latency of 524 ps for a 32-bit operation, at the designed DC bias voltage of 2.5 mV, via precise control of interconnect delays and clock distribution. Furthermore, it achieved a throughput of 6.25 × 10932-bit operations per second. All the correct ALU operations with measured DC bias voltage margins of around 10% at 50 GHz were successfully obtained. The proposed ALU can be used for any 4n-bit processing.

DOI
10.1109/tasc.2015.2507125

Related papers

High performance rapid single-flux-quantum bit-slice arithmetic logic unit

J. R. Ren, Pei-Yao Qu, Jia-Hong Yang +4 more

• A high performance ALU is critical for overall processor performance. • Bypass technology reduces calculation time and prevents data hazards. • Carry-control optimization technology needs minimal hardware costs. • The ALU can perform all operations, achieving up to 100 % utilization. Two optimization technologies, namely, bypass and carry-control optimization, were demonstrated for enhancing the performance of a bit-slice Arithmetic Logic Unit (ALU) in 2 n -bit Rapid Single-Flux-Quantum (RSFQ) microprocessors. These technologies can not only shorten the calculation time but also solve data hazards. Among them, the proposed bypass technology is applicable to any 2 n -bit ALU, whether it is bit-serial, bit-slice or bit-parallel. The high performance bit-slice ALU was implemented using the 6 k A/cm 2 Nb/AlO x /Nb junction fabrication process from Superconducting Electronics Facility of Shanghai Institute of Microsystem and Information Technology. It consists of 1693 Josephson junctions with an area of 2.46 × 0.81 mm 2 . All ALU operations of the MIPS32 instruction set are implemented, including two extended instructions, i.e., addition with carry (ADDC) and subtraction with borrow (SUBB). All the ALU operations were successfully obtained in SFQ testing based on OCTOPUX and the measured DC bias current margin can reach 86 % - 104 % . The ALU achieves a 100 % utilization rate, regardless of carry/borrow read-after-write correlations between instructions.

Superconductivity•Sep 1, 2024•4 citations

Logic Design of a 16-bit Bit-Slice Arithmetic Logic Unit for 32-/64-bit RSFQ Microprocessors

Guang-Ming Tang, Pei-Yao Qu, Xiaochun Ye +1 more

A 16-bit bit-slice arithmetic logic unit (ALU) is proposed for 32-/64-bit rapid single-flux-quantum microprocessors. It is based on a Ladner-Fischer adder. The ALU covers all of the ALU operations for MIPS32 instructions set. And each of the two 64-bit operands is divided into four slices of 16 bits each. The ALU uses synchronous concurrent-flow clocking and consists of 11 pipeline stages. The proposed ALU can be used for any 16n-bit processing.

IEEE Transactions on Applied Superconductivity•Jan 31, 2018•33 citations

32 × 32-Bit 4-Bit Bit-Slice Integer Multiplier for RSFQ Microprocessors

Guang-Ming Tang, Kazuyoshi Takagi, Naofumi Takagi

A design of a 32 × 32-bit 4-bit bit-slice integer multiplier for rapid single-flux quantum microprocessors is shown. The multiplier carries out both signed and unsigned multiplication. It is designed with synchronous concurrent-flow clocking and target frequency of 50 GHz using the AIST 1.0-μm Nb/AlOx/Nb, nine-layer advanced process 2 fabrication technology with a critical current density of 10 kA/cm2. It consists of 56 885 Josephson junctions. The area is 12.00 × 6.65 mm2. The simulation results show correct operation with frequency of 50 GHz at the dc bias voltage of 2.5 mV. The throughput is 3.125 × 109multiplications per second.

IEEE Transactions on Applied Superconductivity•Feb 1, 2017•15 citations

ERSFQ 8-Bit Parallel Arithmetic Logic Unit

Alex F. Kirichenko, Igor V. Vernik, Michael Y. Kamkar +4 more

We have designed and tested a parallel 8-bit ERSFQ arithmetic logic unit (ALU). The ALU design employs wave-pipelined instruction execution and features modular bit-slice architecture that is easily extendable to any number of bits and adaptable to current recycling. A carry signal synchronized with an asynchronous instruction propagation provides the wave-pipeline operation of the ALU. The ALU instruction set consists of 14 arithmetical and logical instructions. It has been designed and simulated for operation up to a 10 GHz clock rate at the 10-kA/cm2fabrication process. The ALU is embedded into a shift-register-based high-frequency testbed with on-chip clock generator to allow for comprehensive high frequency testing for all possible operands. The 8-bit ERSFQ ALU, comprising 6840 Josephson junctions, has been fabricated with MIT Lincoln Lab's 10-kA/cm2SFQ5ee fabrication process featuring eight Nb wiring layers and a high-kinetic inductance layer needed for ERSFQ technology. We evaluated the bias margins for all instructions and various operands at both low and high frequency clock. At low frequency, clock and all instruction propagation through ALU were observed with bias margins of +/-11% and +/-9%, respectively. Also at low speed, the ALU exhibited correct functionality for all arithmetical and logical instructions with +/-6% bias margins. We tested the 8-bit ALU for all instructions up to 2.8 GHz clock frequency.

arXiv:1902.09500•IEEE Transactions on Applied Superconductivity•Mar 18, 2019•47 citations

A 4-Bit Bit-Slice Multiplier for a 32-Bit RSFQ Microprocessor

Guang-Ming Tang, Kazuyoshi Takagi, Naofumi Takagi

A 4-bit bit-slice multiplier for a 32-bit rapid single-flux-quantum (RSFQ) microprocessor is proposed. It carries out both signed and unsigned integer multiplication. A fully pipelined RSFQ logic design of the multiplier using concurrent flow clocking consists of 33 stages and 17,551 Josephson junctions. The bit-slice approach simplifies the circuit complexity and reduces the hardware cost. For verification, an 8×8-bit 4-bit bit-slice multiplier based on the proposed algorithm has been designed and simulated using AIST 10-kA/cm21.0-μm fabrication technology. The simulation result shows correct operation at 62.5 GHz.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2015•2 citations

8-Bit Asynchronous Sparse-Tree Superconductor RSFQ Arithmetic-Logic Unit With a Rich Set of Operations

M. Dorojevets, Christopher Lawrence Ayala, Nobuyuki Yoshikawa +1 more

This paper describes the design and testing of an 8-bit asynchronous wave-pipelined sparse-tree Rapid Single Flux Quantum (RSFQ) Arithmetic Logic Unit (ALU). Compared to previously developed RSFQ ALUs, this unit features an extensive set of 8 arithmetic and 12 logical operations. The execution of ALU operations consists of two steps. First, when necessary, one or both operands are inverted, and then operations are performed on these pre-processed data. Unlike the RSFQ Kogge-Stone-based designs, our parallel-prefix sparse-tree ALU has significantly reduced circuit complexity while maintaining robust operational margins at high frequency. An 8-bit ALU has been implemented with the International Superconductivity Technology Center (ISTEC) 10 kA/cm21.0 μm 9-metal ADP2.1 fabrication process as a joint effort between Stony Brook University, Yokohama National University, and Nagoya University. Using the CONNECT cell library and SFQ CAD tools developed at Nagoya and Yokohama, the Stony Brook team has developed a complete logical and physical design of the ALU chip. The 8-bit ALU core (without SFQ-to-dc and dc-to-SFQ converters) consists of 8832 Josephson junctions with an area of 7.2 mm2. Simulations show that the ALU can operate at the maximum rate of 42 GHz. It has the latency of 374 ps at a bias voltage of 2.5 mV. The chip was fabricated and tested at low frequency in 2012. Testing results showed malfunctioning of some gates but despite these shortcomings we still verified several ALU operations with the measured DC bias voltage margins of ±1.8%.

IEEE Transactions on Applied Superconductivity•Nov 21, 2012•35 citations
A 4-bit bit-slice arithmetic logic unit (ALU) for 32-bit rapid single-flux-quantum microprocessors was demonstrated. The proposed ALU covers all of the ALU operations for the MIPS32 instruction set. It processes bit-sliced 32-bit data that are divided into eight slices of 4 bits. The bit-slice approach simplifies the circuit structure and reduces the hardware cost. The ALU uses synchronous concurrent-flow clocking and consists of eight pipeline stages. It was implemented using the 1.0-μm Nb/AlOx/Nb nine-layer advanced process 2 (ADP2) with a critical current density of 10 kA/cm2, and fabricated by National Institute of Advanced Industrial Science and Technology (AIST). It consists of 3481 Josephson junctions with an area of 3.09 × 1.66 mm2. It achieved the target frequency of 50 GHz and a latency of 524 ps for a 32-bit operation, at the designed DC bias voltage of 2.5 mV, via precise control of interconnect delays and clock distribution. Furthermore, it achieved a throughput of 6.25 × 10932-bit operations per second. All the correct ALU operations with measured DC bias voltage margins of around 10% at 50 GHz were successfully obtained. The proposed ALU can be used for any 4n-bit processing.
• A high performance ALU is critical for overall processor performance. • Bypass technology reduces calculation time and prevents data hazards. • Carry-control optimization technology needs minimal hardware costs. • The ALU can perform all operations, achieving up to 100 % utilization. Two optimization technologies, namely, bypass and carry-control optimization, were demonstrated for enhancing the performance of a bit-slice Arithmetic Logic Unit (ALU) in 2 n -bit Rapid Single-Flux-Quantum (RSFQ) microprocessors. These technologies can not only shorten the calculation time but also solve data hazards. Among them, the proposed bypass technology is applicable to any 2 n -bit ALU, whether it is bit-serial, bit-slice or bit-parallel. The high performance bit-slice ALU was implemented using the 6 k A/cm 2 Nb/AlO x /Nb junction fabrication process from Superconducting Electronics Facility of Shanghai Institute of Microsystem and Information Technology. It consists of 1693 Josephson junctions with an area of 2.46 × 0.81 mm 2 . All ALU operations of the MIPS32 instruction set are implemented, including two extended instructions, i.e., addition with carry (ADDC) and subtraction with borrow (SUBB). All the ALU operations were successfully obtained in SFQ testing based on OCTOPUX and the measured DC bias current margin can reach 86 % - 104 % . The ALU achieves a 100 % utilization rate, regardless of carry/borrow read-after-write correlations between instructions.
A design of a 32 × 32-bit 4-bit bit-slice integer multiplier for rapid single-flux quantum microprocessors is shown. The multiplier carries out both signed and unsigned multiplication. It is designed with synchronous concurrent-flow clocking and target frequency of 50 GHz using the AIST 1.0-μm Nb/AlOx/Nb, nine-layer advanced process 2 fabrication technology with a critical current density of 10 kA/cm2. It consists of 56 885 Josephson junctions. The area is 12.00 × 6.65 mm2. The simulation results show correct operation with frequency of 50 GHz at the dc bias voltage of 2.5 mV. The throughput is 3.125 × 109multiplications per second.
We have designed and tested a parallel 8-bit ERSFQ arithmetic logic unit (ALU). The ALU design employs wave-pipelined instruction execution and features modular bit-slice architecture that is easily extendable to any number of bits and adaptable to current recycling. A carry signal synchronized with an asynchronous instruction propagation provides the wave-pipeline operation of the ALU. The ALU instruction set consists of 14 arithmetical and logical instructions. It has been designed and simulated for operation up to a 10 GHz clock rate at the 10-kA/cm2fabrication process. The ALU is embedded into a shift-register-based high-frequency testbed with on-chip clock generator to allow for comprehensive high frequency testing for all possible operands. The 8-bit ERSFQ ALU, comprising 6840 Josephson junctions, has been fabricated with MIT Lincoln Lab's 10-kA/cm2SFQ5ee fabrication process featuring eight Nb wiring layers and a high-kinetic inductance layer needed for ERSFQ technology. We evaluated the bias margins for all instructions and various operands at both low and high frequency clock. At low frequency, clock and all instruction propagation through ALU were observed with bias margins of +/-11% and +/-9%, respectively. Also at low speed, the ALU exhibited correct functionality for all arithmetical and logical instructions with +/-6% bias margins. We tested the 8-bit ALU for all instructions up to 2.8 GHz clock frequency.
A 4-bit bit-slice multiplier for a 32-bit rapid single-flux-quantum (RSFQ) microprocessor is proposed. It carries out both signed and unsigned integer multiplication. A fully pipelined RSFQ logic design of the multiplier using concurrent flow clocking consists of 33 stages and 17,551 Josephson junctions. The bit-slice approach simplifies the circuit complexity and reduces the hardware cost. For verification, an 8×8-bit 4-bit bit-slice multiplier based on the proposed algorithm has been designed and simulated using AIST 10-kA/cm21.0-μm fabrication technology. The simulation result shows correct operation at 62.5 GHz.
This paper describes the design and testing of an 8-bit asynchronous wave-pipelined sparse-tree Rapid Single Flux Quantum (RSFQ) Arithmetic Logic Unit (ALU). Compared to previously developed RSFQ ALUs, this unit features an extensive set of 8 arithmetic and 12 logical operations. The execution of ALU operations consists of two steps. First, when necessary, one or both operands are inverted, and then operations are performed on these pre-processed data. Unlike the RSFQ Kogge-Stone-based designs, our parallel-prefix sparse-tree ALU has significantly reduced circuit complexity while maintaining robust operational margins at high frequency. An 8-bit ALU has been implemented with the International Superconductivity Technology Center (ISTEC) 10 kA/cm21.0 μm 9-metal ADP2.1 fabrication process as a joint effort between Stony Brook University, Yokohama National University, and Nagoya University. Using the CONNECT cell library and SFQ CAD tools developed at Nagoya and Yokohama, the Stony Brook team has developed a complete logical and physical design of the ALU chip. The 8-bit ALU core (without SFQ-to-dc and dc-to-SFQ converters) consists of 8832 Josephson junctions with an area of 7.2 mm2. Simulations show that the ALU can operate at the maximum rate of 42 GHz. It has the latency of 374 ps at a bias voltage of 2.5 mV. The chip was fabricated and tested at low frequency in 2012. Testing results showed malfunctioning of some gates but despite these shortcomings we still verified several ALU operations with the measured DC bias voltage margins of ±1.8%.