Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

8-Bit Asynchronous Sparse-Tree Superconductor RSFQ Arithmetic-Logic Unit With a Rich Set of Operations

M. Dorojevets, Christopher Lawrence Ayala, Nobuyuki Yoshikawa, Akira Fujimaki

Published Nov 21, 2012• 35 citations
Publisher

Abstract

This paper describes the design and testing of an 8-bit asynchronous wave-pipelined sparse-tree Rapid Single Flux Quantum (RSFQ) Arithmetic Logic Unit (ALU). Compared to previously developed RSFQ ALUs, this unit features an extensive set of 8 arithmetic and 12 logical operations. The execution of ALU operations consists of two steps. First, when necessary, one or both operands are inverted, and then operations are performed on these pre-processed data. Unlike the RSFQ Kogge-Stone-based designs, our parallel-prefix sparse-tree ALU has significantly reduced circuit complexity while maintaining robust operational margins at high frequency. An 8-bit ALU has been implemented with the International Superconductivity Technology Center (ISTEC) 10 kA/cm21.0 μm 9-metal ADP2.1 fabrication process as a joint effort between Stony Brook University, Yokohama National University, and Nagoya University. Using the CONNECT cell library and SFQ CAD tools developed at Nagoya and Yokohama, the Stony Brook team has developed a complete logical and physical design of the ALU chip. The 8-bit ALU core (without SFQ-to-dc and dc-to-SFQ converters) consists of 8832 Josephson junctions with an area of 7.2 mm2. Simulations show that the ALU can operate at the maximum rate of 42 GHz. It has the latency of 374 ps at a bias voltage of 2.5 mV. The chip was fabricated and tested at low frequency in 2012. Testing results showed malfunctioning of some gates but despite these shortcomings we still verified several ALU operations with the measured DC bias voltage margins of ±1.8%.

DOI
10.1109/tasc.2012.2229334

Related papers

16-Bit Wave-Pipelined Sparse-Tree RSFQ Adder

M. Dorojevets, Christopher Lawrence Ayala, Nobuyuki Yoshikawa +1 more

In this paper, we discuss the architecture, design, and testing of the first 16-bit asynchronous wave-pipelined sparse-tree superconductor rapid single flux quantum adder implemented using the ISTEC 10 kA/cm2ADP2.1 fabrication process. Compared to the Kogge-Stone adder, our parallel-prefix sparse-tree adder has better energy efficiency with significantly reduced complexity (at the expense of latency) and almost no decrease in operation frequency. The 16-bit adder core (without SFQ-to-dc and dc-to-SFQ converters) has 9941 Josephson junctions occupying an area of 8.5 mm2. It is designed for the target operation frequency of 30 GHz with the expected latency of 352 ps at the bias voltage of 2.5 mV. The adder chip was fabricated and successfully tested at low frequency for all test patterns with measured bias margins of +9.8%/-10.7%.

IEEE Transactions on Applied Superconductivity•Dec 12, 2012•35 citations

20GHz Operation of an Asynchronous Wave-Pipelined RSFQ Arithmetic-Logic Unit

Timur V. Filippov, Anubhav Sahu, Alex F. Kirichenko +4 more

We have designed and tested at high frequency an RSFQ-based Arithmetic-Logic Unit (ALU), the critical component of an 8-bit RSFQ processor datapath. The ALU design is based on a Kogge-Stone adder and employs an asynchronous wave-pipelined approach scalable for wide datapath processors. The 8-bit ALU circuit was fabricated with HYPRES’ standard 4.5 kA/cm2 process and consists of 7,950 Josephson junctions, including input and output interfaces. In this paper, we present chip design and high-speed test results for the 8-bit ALU circuit.

Physics Procedia•Jan 1, 2012•107 citations

ERSFQ 8-Bit Parallel Arithmetic Logic Unit

Alex F. Kirichenko, Igor V. Vernik, Michael Y. Kamkar +4 more

We have designed and tested a parallel 8-bit ERSFQ arithmetic logic unit (ALU). The ALU design employs wave-pipelined instruction execution and features modular bit-slice architecture that is easily extendable to any number of bits and adaptable to current recycling. A carry signal synchronized with an asynchronous instruction propagation provides the wave-pipeline operation of the ALU. The ALU instruction set consists of 14 arithmetical and logical instructions. It has been designed and simulated for operation up to a 10 GHz clock rate at the 10-kA/cm2fabrication process. The ALU is embedded into a shift-register-based high-frequency testbed with on-chip clock generator to allow for comprehensive high frequency testing for all possible operands. The 8-bit ERSFQ ALU, comprising 6840 Josephson junctions, has been fabricated with MIT Lincoln Lab's 10-kA/cm2SFQ5ee fabrication process featuring eight Nb wiring layers and a high-kinetic inductance layer needed for ERSFQ technology. We evaluated the bias margins for all instructions and various operands at both low and high frequency clock. At low frequency, clock and all instruction propagation through ALU were observed with bias margins of +/-11% and +/-9%, respectively. Also at low speed, the ALU exhibited correct functionality for all arithmetical and logical instructions with +/-6% bias margins. We tested the 8-bit ALU for all instructions up to 2.8 GHz clock frequency.

arXiv:1902.09500•IEEE Transactions on Applied Superconductivity•Mar 18, 2019•47 citations

4-bit Bit-Slice Arithmetic Logic Unit for 32-bit RSFQ Microprocessors

Guang-Ming Tang, Takata Kensuke, Masamitsu Tanaka +3 more

A 4-bit bit-slice arithmetic logic unit (ALU) for 32-bit rapid single-flux-quantum microprocessors was demonstrated. The proposed ALU covers all of the ALU operations for the MIPS32 instruction set. It processes bit-sliced 32-bit data that are divided into eight slices of 4 bits. The bit-slice approach simplifies the circuit structure and reduces the hardware cost. The ALU uses synchronous concurrent-flow clocking and consists of eight pipeline stages. It was implemented using the 1.0-μm Nb/AlOx/Nb nine-layer advanced process 2 (ADP2) with a critical current density of 10 kA/cm2, and fabricated by National Institute of Advanced Industrial Science and Technology (AIST). It consists of 3481 Josephson junctions with an area of 3.09 × 1.66 mm2. It achieved the target frequency of 50 GHz and a latency of 524 ps for a 32-bit operation, at the designed DC bias voltage of 2.5 mV, via precise control of interconnect delays and clock distribution. Furthermore, it achieved a throughput of 6.25 × 10932-bit operations per second. All the correct ALU operations with measured DC bias voltage margins of around 10% at 50 GHz were successfully obtained. The proposed ALU can be used for any 4n-bit processing.

IEEE Transactions on Applied Superconductivity•Dec 10, 2015•64 citations

80-GHz Operation of an 8-Bit RSFQ Arithmetic Logic Unit

Yuki Ando, Ryo Sato, Masamitsu Tanaka +2 more

We have designed and demonstrated an arithmetic logic unit (ALU) based on rapid single-flux-quantum (RSFQ) technology. The ALU has been developed toward demonstration of high-performance information processing using a general purpose microprocessor CORE e4. The target operation frequency of the ALU is 50 GHz. In this paper, we present the design and high- speed functionality test results of the ALU. The ALU can execute 10 instructions. We aimed at high frequency operation with precise timing design using logic gates synchronized to the clock signal. The ALU contains 1555 Josephson junctions (JJs) and occupies a circuit area of 0.53mm2. We have demonstrated the correct operation of the ALU using on-chip high-speed test. The estimated maximum operating frequency based on measurement results is 80 GHz.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2015•21 citations

High-Speed Operation of 0.25-mV RSFQ Arithmetic Logic Unit Based on 10-kA/cm2 Nb Process Technology

Masamitsu Tanaka, Kitayama Atsushi, Masakazu Okada +4 more

We report the successful operation of a low-power arithmetic logic unit (ALU) based on a low-voltage rapid single-flux-quantum (LV-RSFQ) logic circuit, whereby a dc bias current is fed to circuits from lowered constant-voltage sources through small resistors. Both the static and dynamic energy consumptions are reduced because of the reduction in the amplitudes of voltage pulses across the Josephson junctions, with a trade-off of slightly slower switching speeds. The designed bias voltage was set to 0.25mV, which is one-tenth that of our standard RSFQ circuit design. We investigated several issues related to such low-voltage operation, including margins and timing design. To achieve successful operation, we tuned the circuit parameters in the logic gate design and carefully controlled the timing by considering the interference of pulse signals. We show test results for the low-voltage ALU in on-chip high-speed testing. The circuit was fabricated using the AIST Nb/AlOx/Nb Advanced Process with a critical current density of 10kA/cm2. We verified that arithmetic and logical operations were correctly implemented and obtained dc bias margins of 18% at a target clock frequency of 20GHz and achieved a maximum clock frequency of 28GHz with a power consumption of 28µW. These experimental results indicate energy efficiency of 3.6 times that of the standard RSFQ circuit design.

IEICE Transactions on Electronics•Jan 1, 2014•8 citations
This paper describes the design and testing of an 8-bit asynchronous wave-pipelined sparse-tree Rapid Single Flux Quantum (RSFQ) Arithmetic Logic Unit (ALU). Compared to previously developed RSFQ ALUs, this unit features an extensive set of 8 arithmetic and 12 logical operations. The execution of ALU operations consists of two steps. First, when necessary, one or both operands are inverted, and then operations are performed on these pre-processed data. Unlike the RSFQ Kogge-Stone-based designs, our parallel-prefix sparse-tree ALU has significantly reduced circuit complexity while maintaining robust operational margins at high frequency. An 8-bit ALU has been implemented with the International Superconductivity Technology Center (ISTEC) 10 kA/cm21.0 μm 9-metal ADP2.1 fabrication process as a joint effort between Stony Brook University, Yokohama National University, and Nagoya University. Using the CONNECT cell library and SFQ CAD tools developed at Nagoya and Yokohama, the Stony Brook team has developed a complete logical and physical design of the ALU chip. The 8-bit ALU core (without SFQ-to-dc and dc-to-SFQ converters) consists of 8832 Josephson junctions with an area of 7.2 mm2. Simulations show that the ALU can operate at the maximum rate of 42 GHz. It has the latency of 374 ps at a bias voltage of 2.5 mV. The chip was fabricated and tested at low frequency in 2012. Testing results showed malfunctioning of some gates but despite these shortcomings we still verified several ALU operations with the measured DC bias voltage margins of ±1.8%.
In this paper, we discuss the architecture, design, and testing of the first 16-bit asynchronous wave-pipelined sparse-tree superconductor rapid single flux quantum adder implemented using the ISTEC 10 kA/cm2ADP2.1 fabrication process. Compared to the Kogge-Stone adder, our parallel-prefix sparse-tree adder has better energy efficiency with significantly reduced complexity (at the expense of latency) and almost no decrease in operation frequency. The 16-bit adder core (without SFQ-to-dc and dc-to-SFQ converters) has 9941 Josephson junctions occupying an area of 8.5 mm2. It is designed for the target operation frequency of 30 GHz with the expected latency of 352 ps at the bias voltage of 2.5 mV. The adder chip was fabricated and successfully tested at low frequency for all test patterns with measured bias margins of +9.8%/-10.7%.
We have designed and tested at high frequency an RSFQ-based Arithmetic-Logic Unit (ALU), the critical component of an 8-bit RSFQ processor datapath. The ALU design is based on a Kogge-Stone adder and employs an asynchronous wave-pipelined approach scalable for wide datapath processors. The 8-bit ALU circuit was fabricated with HYPRES’ standard 4.5 kA/cm2 process and consists of 7,950 Josephson junctions, including input and output interfaces. In this paper, we present chip design and high-speed test results for the 8-bit ALU circuit.
We have designed and tested a parallel 8-bit ERSFQ arithmetic logic unit (ALU). The ALU design employs wave-pipelined instruction execution and features modular bit-slice architecture that is easily extendable to any number of bits and adaptable to current recycling. A carry signal synchronized with an asynchronous instruction propagation provides the wave-pipeline operation of the ALU. The ALU instruction set consists of 14 arithmetical and logical instructions. It has been designed and simulated for operation up to a 10 GHz clock rate at the 10-kA/cm2fabrication process. The ALU is embedded into a shift-register-based high-frequency testbed with on-chip clock generator to allow for comprehensive high frequency testing for all possible operands. The 8-bit ERSFQ ALU, comprising 6840 Josephson junctions, has been fabricated with MIT Lincoln Lab's 10-kA/cm2SFQ5ee fabrication process featuring eight Nb wiring layers and a high-kinetic inductance layer needed for ERSFQ technology. We evaluated the bias margins for all instructions and various operands at both low and high frequency clock. At low frequency, clock and all instruction propagation through ALU were observed with bias margins of +/-11% and +/-9%, respectively. Also at low speed, the ALU exhibited correct functionality for all arithmetical and logical instructions with +/-6% bias margins. We tested the 8-bit ALU for all instructions up to 2.8 GHz clock frequency.
A 4-bit bit-slice arithmetic logic unit (ALU) for 32-bit rapid single-flux-quantum microprocessors was demonstrated. The proposed ALU covers all of the ALU operations for the MIPS32 instruction set. It processes bit-sliced 32-bit data that are divided into eight slices of 4 bits. The bit-slice approach simplifies the circuit structure and reduces the hardware cost. The ALU uses synchronous concurrent-flow clocking and consists of eight pipeline stages. It was implemented using the 1.0-μm Nb/AlOx/Nb nine-layer advanced process 2 (ADP2) with a critical current density of 10 kA/cm2, and fabricated by National Institute of Advanced Industrial Science and Technology (AIST). It consists of 3481 Josephson junctions with an area of 3.09 × 1.66 mm2. It achieved the target frequency of 50 GHz and a latency of 524 ps for a 32-bit operation, at the designed DC bias voltage of 2.5 mV, via precise control of interconnect delays and clock distribution. Furthermore, it achieved a throughput of 6.25 × 10932-bit operations per second. All the correct ALU operations with measured DC bias voltage margins of around 10% at 50 GHz were successfully obtained. The proposed ALU can be used for any 4n-bit processing.
We have designed and demonstrated an arithmetic logic unit (ALU) based on rapid single-flux-quantum (RSFQ) technology. The ALU has been developed toward demonstration of high-performance information processing using a general purpose microprocessor CORE e4. The target operation frequency of the ALU is 50 GHz. In this paper, we present the design and high- speed functionality test results of the ALU. The ALU can execute 10 instructions. We aimed at high frequency operation with precise timing design using logic gates synchronized to the clock signal. The ALU contains 1555 Josephson junctions (JJs) and occupies a circuit area of 0.53mm2. We have demonstrated the correct operation of the ALU using on-chip high-speed test. The estimated maximum operating frequency based on measurement results is 80 GHz.
We report the successful operation of a low-power arithmetic logic unit (ALU) based on a low-voltage rapid single-flux-quantum (LV-RSFQ) logic circuit, whereby a dc bias current is fed to circuits from lowered constant-voltage sources through small resistors. Both the static and dynamic energy consumptions are reduced because of the reduction in the amplitudes of voltage pulses across the Josephson junctions, with a trade-off of slightly slower switching speeds. The designed bias voltage was set to 0.25mV, which is one-tenth that of our standard RSFQ circuit design. We investigated several issues related to such low-voltage operation, including margins and timing design. To achieve successful operation, we tuned the circuit parameters in the logic gate design and carefully controlled the timing by considering the interference of pulse signals. We show test results for the low-voltage ALU in on-chip high-speed testing. The circuit was fabricated using the AIST Nb/AlOx/Nb Advanced Process with a critical current density of 10kA/cm2. We verified that arithmetic and logical operations were correctly implemented and obtained dc bias margins of 18% at a target clock frequency of 20GHz and achieved a maximum clock frequency of 28GHz with a power consumption of 28µW. These experimental results indicate energy efficiency of 3.6 times that of the standard RSFQ circuit design.