Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

A theoretical investigation of the optical gain in waveguide based on a silica matrix containing silicon nanograins and doped either withNd3+ or with Er3+ ions

Alexandre Fafin, Julien Cardin, Christian Dufour, Fabrice Gourbilleau

Published May 11, 2015• 0 citations
OpenAlex

Abstract

We aim to amplify a signal in a strip loaded waveguide composed by an active silica layer co-doped with silicon nanograins and rare-earth ions deposited on a silica cladding layer and topped by a silica strip. The signal wavelength corresponds to the transition wavelength between two energy levels of a rare earth ions. To achieve an efficient population inversion, the rare earth ions benefit from the indirect excitation via silicon nanograins which show an absorption cross section fourfold higher than the one of rare earth ions. In order to study the influence of the type of rare earth on the optical gain, we consider two rare earth ions : neodymium ions (Nd3+) for a signal wavelength at 1060 nm and erbium ions (Er3+) for a signal wavelength at 1540 nm. The optical gain is simulated using a modified two loops auxiliary-differential equation and finite-difference time-domain (ADE-FDTD) algorithm. Within this new scheme we can compute the steady state levels populations as well as the spatial distribution of the guided field in the waveguide whatever the populations levels lifetime considered. We also calculate the gross gain as well as the net gain by taking into account the experimental background losses. We demonstrate that a significant positive net gain can only be achieved with the Nd3+ doped waveguide up to 30 dB/cm for a pump power density of 10^4 mW/mm².

Related papers

Energy transfer in erbium doped optical waveguides based on silicon

Pieter G. Kik

Energy transfer in erbium doped optical waveguides based on silicon This thesis describes the energy transfer processes\noccurring in materials that can be used for the fabrication of silicon compatible optical integrated circuits, operating at 1.54 mm.The thesis consists of three parts: Part I discusses energy transfer in optical waveguide amplifiers on silicon. The waveguide amplifiers use an intra-4f transition of the rare earth ion erbium occurring at 1.54 mm. To achieve significant amplification, high\n Er concentrations (> 10 20 cm -3 ) are required. At these concentrations Er ions can interact, resulting in co-operative\n upconversion, in which one excited Er ion is excited into a higher energy state, while a neighboring Er ion returns to the ground\n state. In Part I this and other gain limiting effects are investigated. In particular, it is shown that the atomic-scale Er distribution\n is of crucial importance for the performance of Er doped waveguide amplifiers. Part II discusses the energy transfer processes\n occurring in Er doped silicon. It is shown that Er in silicon can be excited by electron-hole pair recombination in an\n impurity-Auger effect. This effect may be used to fabricate an electrically pumped Er doped waveguide amplifier. The reverse\n process can also occur: an excited Er ion can de-excite and generate an electron-hole pair in the silicon, due to a non-radiative\n backtransfer process. This process has an efficiency of 70% at room temperature. This observation enables the fabrication of an\n Er doped photo-detector in a Si waveguide operating at 1.54 mm. The performance of such a detector is discussed. Part III\n discusses the interaction between Er and silicon nanocrystals embedded in SiO2. Si nanocrystals efficiently absorb visible light,\n resulting in the generation of quantum confined electron-hole pairs. The electron-hole pairs efficiently transfer energy to Er.\n Due to the energy transfer, the effective Er absorption cross section is five orders of magnitude larger than for direct optical\n excitation. Silicon nanocrystals may thus be used to increase the pumping efficiency of an Er doped waveguide amplifier. It is\n shown that a single nanocrystal can excite ~1 Er ion at a time and that an optical gain of 0.6 dB/cm may be achieved in a typical\n nanocrystal sensitized waveguide amplifier. Due to the broad absorption band of Si nanocrystals, a broad band light source can\n be used as pump source in such a nanocrystal sensitized Er doped waveguide amplifier.

•Sep 18, 2000•11 citations

Photonic Crystal Microcavity Amplifier

D. Biallo, Antonella D’Orazio, M. De Sario +3 more

Summary form only given: Amplification in rare-earth doped solid state planar optical structures has attracted a lot of interest in recent years due to the fact that the rare earth ions show sharp absorption and emission bands and relatively long luminescence lifetimes. In particular the erbium (Er) ion is very attractive because of its intra 4f-transition from the first excited state to the ground state around 1.53 mum (4I13/2-4I15/2). The main problem of the erbium doped waveguide amplifiers (EDWAs) is that high values of the Er3+concentration are required to reach high gain figures in a compact length, but in this way the concentration quenching effects become very considerable and detrimental to the optical gain, since they reduce the population in the first excited state. A good solution to overcome this dramatic drawback is to consider erbium doped photonic crystal amplifier (EDPCA). In fact the small group velocity of electromagnetic eigenmodes brings about the enhancement of stimulated emission if the photonic crystals are doped by active media as the rare earth ions E3+r or Yt3+. This phenomenon originates from the long interaction time between radiation field and the matter caused by the small group velocity near the edge of the photonic band gap. The efficient confinement of light is achievable not only by tuning the input signal at the band edge of the gap of the photonic crystal but it is also obtainable by introducing local defects inside photonic crystals. The density of electromagnetic states inside a cavity is significantly modified and the spontaneous emission of atoms in a cavity can be either enhanced or inhibited. Erbium doped silica-titania one-dimensional photonic crystal microcavities have been analyzed by solving the erbium rate equations and the Maxwell equations by means of an auxiliary differential equation finite difference time domain technique. Since the performance of optical amplifiers depends on the populations of the energy levels participating in radiative transitions, determined principally by the distribution and concentration of the rare-earth ions and by the pumping conditions, the relations between these parameters and the transmittance of the EDPCMA have been studied

International Conference on Transparent Optical Networks•Jun 1, 2006•0 citations

INVESTIGATION OF LIGHT AMPLIFICATION IN SI-NANOCRYSTAL-ER DOPED OPTICAL FIBER

Ali Rostami, Ahmad Salmanogli

Abstract—In this article the details of Erbium doped Fiber Amplifier (EDFA) in presence of Silicon nanocrystal (Si-Nc) is investigated. In this analysis Si-Nc and Er ions in matrix of fiber are assumed two and five levels respectively. For this structure rate equation for transient and steady state analysis is considered. The range of Er (+3) concentration and pump intensity at 488 nm are considered [10 17 − 10 21]1/cm 3 and [10 17 − 10 23] photon/cm 2 · sec respectively in this paper. Based on numerical simulation of this problem we observed that with increasing of concentration of the Si-Nc the fiber length for given optical gain is decreased. For example in the case of 40 dB optical gain, we calculated fiber length to be 1.1 × 10 5 cm without Si-Nc and 5 × 10 2 cm for σCCa = 1 × 10 −17 cm 2 (confined carrier absorption cross-section) and 5 cm for σCCa =1 × 10 −19 cm 2 respectively. Our simulations show that for second level with increasing pump intensity the population rise and fall times are decreased. But, for third level the population rise time is decreased and fall time is depends to level of Er ion interactions. We observed that with increasing Er ions optical net gain is increased and finally has a maximum. After this special value of Er ions because of increasing in interaction between ions the net gain finally begin to decrease. In this analysis we let to Er ions have inhomogeneous distribution. Also, we observed that in this case with increasing of the distribution peak, the net gain is increased, interaction between ions is increased, the coupling coefficient to the Si-Ncs is increased and losses due to Si-Ncs are decreased. Finally effect of Kexiton (maximum number of exciton in single Si-Nc) on amplification process is considered and we observed that in the case of Kexiton = 2 the optical gain considerably and introduced losses due to Si-Nc are increased. 28 Rostami and SalmanOgli 1.

Progress In Electromagnetics Research B•Jan 1, 2008•15 citations

E-band neodymium-doped fiber amplifier: model and application

Charles D. Boley, Jay W. Dawson, Leily Kiani +1 more

To analyze recent experiments with a neodymium-doped fiber amplifier operating in the E-band of wavelengths (1350-1450 nm) and embedded in fused silica, we develop a time-dependent model consisting of rate equations for the aggregate ion populations and the radiation intensities along the amplifier axis. Both copropagating and counterpropagating intensities, including amplified spontaneous emission, are incorporated. The wavelength-dependent cross section for excited state absorption is inferred from auxiliary measurements. Steady-state solutions are obtained over a range of seed wavelengths and powers. The resulting gain curves agree with experiment at low to intermediate powers (less than ∼1 mW). With a proposed addition to the system loss, the agreement extends to saturation (∼100 mW).

Applied Optics•Mar 15, 2019•21 citations

Achieving optical gain in waveguide-confined nanocluster-sensitized erbium by pulsed excitation

Gerald M. Miller, Ryan M. Briggs, Harry A. Atwater

We use a rate equation approach to model the conditions for optical gain in nanocluster sensitized erbium in a slot waveguide geometry. We determine the viability of achieving net gain for the range of reported values of the carrier absorption cross section for silicon nanoclusters. After accounting for the local density of optical states modification of the emission rates, we find that gain is impossible in continuous wave pumping due to carrier absorption, regardless of the carrier absorption cross section. We, therefore, propose a pulsed electrical operation scheme which mitigates carrier absorption by taking advantage of the short lifetime of silicon nanoclusters compared to erbium. We show that pulsed excitation of a 10 nm layer achieves a modal gain of 0.9 dB/cm during each pulse. Furthermore this gain can be increased to 2 dB/cm by pumping a 50 nm layer.

Journal of Applied Physics•Sep 15, 2010•23 citations

Optical amplification in Er3+-doped transparent Ba2NaNb5O15 single crystal at 850 nm

Patricia Haro‐González, Inocencio Rafael Martin, F.J. Lahoz +3 more

Positive optical gain around 5 cm−1 (∼21 dB/cm) has been observed in Er3+-doped Ba2NaNb5O15 single crystal using a pump and probe experimental setup. High power laser pulses at 532 nm have been used as the pump source in order to strongly populate the S43/2(H211/2) levels of the Er3+ ions due to ground state absorption. Low signal beam cw laser radiation at 850 nm has been used as the probe beam to stimulate the emission associated with the S43/2(H211/2)→I413/2 electronic transition of the Er3+ ions. The process has been modelized as a four level system, and its population has been analyzed and simulated in order to study the gain dynamics. Optical amplification of the probe signal has been observed during the first 60 μs, which represents a good agreement between the measured lifetime of the S43/2(H211/2) levels and the reported simulation.

Journal of Applied Physics•Dec 1, 2009•8 citations
We aim to amplify a signal in a strip loaded waveguide composed by an active silica layer co-doped with silicon nanograins and rare-earth ions deposited on a silica cladding layer and topped by a silica strip. The signal wavelength corresponds to the transition wavelength between two energy levels of a rare earth ions. To achieve an efficient population inversion, the rare earth ions benefit from the indirect excitation via silicon nanograins which show an absorption cross section fourfold higher than the one of rare earth ions. In order to study the influence of the type of rare earth on the optical gain, we consider two rare earth ions : neodymium ions (Nd3+) for a signal wavelength at 1060 nm and erbium ions (Er3+) for a signal wavelength at 1540 nm. The optical gain is simulated using a modified two loops auxiliary-differential equation and finite-difference time-domain (ADE-FDTD) algorithm. Within this new scheme we can compute the steady state levels populations as well as the spatial distribution of the guided field in the waveguide whatever the populations levels lifetime considered. We also calculate the gross gain as well as the net gain by taking into account the experimental background losses. We demonstrate that a significant positive net gain can only be achieved with the Nd3+ doped waveguide up to 30 dB/cm for a pump power density of 10^4 mW/mm².
Energy transfer in erbium doped optical waveguides based on silicon This thesis describes the energy transfer processes\noccurring in materials that can be used for the fabrication of silicon compatible optical integrated circuits, operating at 1.54 mm.The thesis consists of three parts: Part I discusses energy transfer in optical waveguide amplifiers on silicon. The waveguide amplifiers use an intra-4f transition of the rare earth ion erbium occurring at 1.54 mm. To achieve significant amplification, high\n Er concentrations (> 10 20 cm -3 ) are required. At these concentrations Er ions can interact, resulting in co-operative\n upconversion, in which one excited Er ion is excited into a higher energy state, while a neighboring Er ion returns to the ground\n state. In Part I this and other gain limiting effects are investigated. In particular, it is shown that the atomic-scale Er distribution\n is of crucial importance for the performance of Er doped waveguide amplifiers. Part II discusses the energy transfer processes\n occurring in Er doped silicon. It is shown that Er in silicon can be excited by electron-hole pair recombination in an\n impurity-Auger effect. This effect may be used to fabricate an electrically pumped Er doped waveguide amplifier. The reverse\n process can also occur: an excited Er ion can de-excite and generate an electron-hole pair in the silicon, due to a non-radiative\n backtransfer process. This process has an efficiency of 70% at room temperature. This observation enables the fabrication of an\n Er doped photo-detector in a Si waveguide operating at 1.54 mm. The performance of such a detector is discussed. Part III\n discusses the interaction between Er and silicon nanocrystals embedded in SiO2. Si nanocrystals efficiently absorb visible light,\n resulting in the generation of quantum confined electron-hole pairs. The electron-hole pairs efficiently transfer energy to Er.\n Due to the energy transfer, the effective Er absorption cross section is five orders of magnitude larger than for direct optical\n excitation. Silicon nanocrystals may thus be used to increase the pumping efficiency of an Er doped waveguide amplifier. It is\n shown that a single nanocrystal can excite ~1 Er ion at a time and that an optical gain of 0.6 dB/cm may be achieved in a typical\n nanocrystal sensitized waveguide amplifier. Due to the broad absorption band of Si nanocrystals, a broad band light source can\n be used as pump source in such a nanocrystal sensitized Er doped waveguide amplifier.
Summary form only given: Amplification in rare-earth doped solid state planar optical structures has attracted a lot of interest in recent years due to the fact that the rare earth ions show sharp absorption and emission bands and relatively long luminescence lifetimes. In particular the erbium (Er) ion is very attractive because of its intra 4f-transition from the first excited state to the ground state around 1.53 mum (4I13/2-4I15/2). The main problem of the erbium doped waveguide amplifiers (EDWAs) is that high values of the Er3+concentration are required to reach high gain figures in a compact length, but in this way the concentration quenching effects become very considerable and detrimental to the optical gain, since they reduce the population in the first excited state. A good solution to overcome this dramatic drawback is to consider erbium doped photonic crystal amplifier (EDPCA). In fact the small group velocity of electromagnetic eigenmodes brings about the enhancement of stimulated emission if the photonic crystals are doped by active media as the rare earth ions E3+r or Yt3+. This phenomenon originates from the long interaction time between radiation field and the matter caused by the small group velocity near the edge of the photonic band gap. The efficient confinement of light is achievable not only by tuning the input signal at the band edge of the gap of the photonic crystal but it is also obtainable by introducing local defects inside photonic crystals. The density of electromagnetic states inside a cavity is significantly modified and the spontaneous emission of atoms in a cavity can be either enhanced or inhibited. Erbium doped silica-titania one-dimensional photonic crystal microcavities have been analyzed by solving the erbium rate equations and the Maxwell equations by means of an auxiliary differential equation finite difference time domain technique. Since the performance of optical amplifiers depends on the populations of the energy levels participating in radiative transitions, determined principally by the distribution and concentration of the rare-earth ions and by the pumping conditions, the relations between these parameters and the transmittance of the EDPCMA have been studied
Abstract—In this article the details of Erbium doped Fiber Amplifier (EDFA) in presence of Silicon nanocrystal (Si-Nc) is investigated. In this analysis Si-Nc and Er ions in matrix of fiber are assumed two and five levels respectively. For this structure rate equation for transient and steady state analysis is considered. The range of Er (+3) concentration and pump intensity at 488 nm are considered [10 17 − 10 21]1/cm 3 and [10 17 − 10 23] photon/cm 2 · sec respectively in this paper. Based on numerical simulation of this problem we observed that with increasing of concentration of the Si-Nc the fiber length for given optical gain is decreased. For example in the case of 40 dB optical gain, we calculated fiber length to be 1.1 × 10 5 cm without Si-Nc and 5 × 10 2 cm for σCCa = 1 × 10 −17 cm 2 (confined carrier absorption cross-section) and 5 cm for σCCa =1 × 10 −19 cm 2 respectively. Our simulations show that for second level with increasing pump intensity the population rise and fall times are decreased. But, for third level the population rise time is decreased and fall time is depends to level of Er ion interactions. We observed that with increasing Er ions optical net gain is increased and finally has a maximum. After this special value of Er ions because of increasing in interaction between ions the net gain finally begin to decrease. In this analysis we let to Er ions have inhomogeneous distribution. Also, we observed that in this case with increasing of the distribution peak, the net gain is increased, interaction between ions is increased, the coupling coefficient to the Si-Ncs is increased and losses due to Si-Ncs are decreased. Finally effect of Kexiton (maximum number of exciton in single Si-Nc) on amplification process is considered and we observed that in the case of Kexiton = 2 the optical gain considerably and introduced losses due to Si-Nc are increased. 28 Rostami and SalmanOgli 1.
To analyze recent experiments with a neodymium-doped fiber amplifier operating in the E-band of wavelengths (1350-1450 nm) and embedded in fused silica, we develop a time-dependent model consisting of rate equations for the aggregate ion populations and the radiation intensities along the amplifier axis. Both copropagating and counterpropagating intensities, including amplified spontaneous emission, are incorporated. The wavelength-dependent cross section for excited state absorption is inferred from auxiliary measurements. Steady-state solutions are obtained over a range of seed wavelengths and powers. The resulting gain curves agree with experiment at low to intermediate powers (less than ∼1 mW). With a proposed addition to the system loss, the agreement extends to saturation (∼100 mW).
We use a rate equation approach to model the conditions for optical gain in nanocluster sensitized erbium in a slot waveguide geometry. We determine the viability of achieving net gain for the range of reported values of the carrier absorption cross section for silicon nanoclusters. After accounting for the local density of optical states modification of the emission rates, we find that gain is impossible in continuous wave pumping due to carrier absorption, regardless of the carrier absorption cross section. We, therefore, propose a pulsed electrical operation scheme which mitigates carrier absorption by taking advantage of the short lifetime of silicon nanoclusters compared to erbium. We show that pulsed excitation of a 10 nm layer achieves a modal gain of 0.9 dB/cm during each pulse. Furthermore this gain can be increased to 2 dB/cm by pumping a 50 nm layer.
Positive optical gain around 5 cm−1 (∼21 dB/cm) has been observed in Er3+-doped Ba2NaNb5O15 single crystal using a pump and probe experimental setup. High power laser pulses at 532 nm have been used as the pump source in order to strongly populate the S43/2(H211/2) levels of the Er3+ ions due to ground state absorption. Low signal beam cw laser radiation at 850 nm has been used as the probe beam to stimulate the emission associated with the S43/2(H211/2)→I413/2 electronic transition of the Er3+ ions. The process has been modelized as a four level system, and its population has been analyzed and simulated in order to study the gain dynamics. Optical amplification of the probe signal has been observed during the first 60 μs, which represents a good agreement between the measured lifetime of the S43/2(H211/2) levels and the reported simulation.