Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Quantization of a Low-Density Parity-Check (LDPC) Decoder: Limited-Precision Digital Design of the Sum-Product Algorithm (SPA) for Wireless Voice and Video Communication Channels

Raymond Moberly

Published Jul 9, 2013• 0 citations
OpenAlex

Abstract

of the Dissertation Quantization of a Low-Density Parity-Check (LDPC) Decoder: Limited-Precision Digital Design of the Sum-Product Algorithm (SPA) for Wireless Voice and Video Communication Channels. by Raymond B Moberly Claremont Graduate University and San Diego State University: 2012 This dissertation presents two-bit and three-bit quantizations for Sum Product Algorithm (SPA) decoding of Low-Density Parity-Check (LDPC) codes. The study involves evaluation of both decoding performance and hardware implementation requirements. Trade-o s between these factors are considered. The quantizations are simulated in software to measure decoding performance. While quantization e ects are the focal point of the research, a comparison of the number of decoding iterations and of the number of bits of precision used in the decoder are both presented along with the quantization experiments. Decoder performance, measured in terms of both Bit Error Rate (BER) and Frame Error Rate (FER), is tested for each two-bit and three-bit quantization over a range of Signal to Noise Ratio (SNR) values. No single quantization outperforms all other quantizations for the entire tested SNR range. Analysis of the SPA is performed, revealing strategies for computational e ciency and digital design. The hardware designs combine the parity-check and variable-node update steps of the SPA into a single update computation. The update computation is implemented in a hardware design language (HDL), synthesized to programmable logic, and then tested on a Field Programmable Gate Array (FPGA). Hardware implementation requirements, as measured from the synthesis results, are evaluated and compared to a selection of other published works, particularly the work of Planjery et al. A exible implementation is proposed that can adapt the quantization as the channel conditions change.

Related papers

Efficient quantization algorithm for low-density parity-check code decoding

Jianhua Lü

A variable step uniform quantization(VSUQ) sum-product algorithm(SPA) was developed to reduce the hardware complexity of low-density parity-check(LDPC) code decoding.The extrinsic information in the check nodes and bit nodes is quantized in the same quantization step.Then,the quantization steps for the check nodes and bit nodes are multiplied and divided by a predetermined parameter.Simulation and implementation using a field programmable gate array(FPGA) show that the performance degradation in the algorithm is within 0.1 dB comparing to the unquantized standard SPA,while reducing the hardware size by 50% comparing to a uniform quantization SPA with the same performance.

Journal of Tsinghua University(Science and Technology)•Jan 1, 2007•0 citations

Low Complexity Implementations of Sum-Product Algorithm for Decoding Low-Density Parity-Check Codes

Daesun Oh, Keshab K. Parhi

In this paper, we propose low complexity implementations of sum-product algorithm (SPA) for decoding low-density parity-check (LDPC) codes. The finite precision implementations for SPA have an important tradeoff between the decoding performance and hardware complexity caused by two dominant area consuming factors. One is the memory for updated messages storage and the other is the look-up table (LUT) for implementation of nonlinear function Psi(x). The proposed two types of variable quantization schemes result in significant reductions of LUT sizes. Computer simulation results indicate that the performance losses of SPA with reduced LUT by proposed schemes are less than 0.05 dB compared to that of SPA with original LUT. Moreover, the proposed implementation offers a large reduction in the finite wordlength for storage of updated messages using a kind of compression technique without performance losses. As a result, using the proposed implementation based on variable quantization scheme and data compression technique, the novel proposed implementation for SPA decoder architecture offers significant reductions of 75% and 33% in hardware complexities of LUT and memories, respectively, without significant performance degradations over conventional uniform quantization scheme. Furthermore, since each LUT with variable (6:3) quantization scheme II has only 8 entries, its hardware implementation can be replaced with a small combination circuit instead of readonly-memory (ROM) for LUT

SiPS ... design and implementation - IEEE Workshop on Signal Processing Systems•Oct 1, 2006•18 citations

Efficient implementation of the sum-product algorithm forquantized decoding of LDPC codes

Wang Xin-meii

An efficient implementation of the Sum-Product algorithm(SPA) in the log-likelihood ratio (LLR) domain is presented in [1]. In this paper, We modify a formula in [1] such that SPA can be implemented by using two small look-up tables. With this modification, all the calculations involved in this implementation involve only additions, subtractions, comparisons and table looking-ups, which leads to low computation complexity and facility in hardware implementation. Based on this modified implementation, various quantization schemes of SPA for decoding low-density parity-check (LDPC) codes are investigated. And the issues related to quantization, such as clipping levels and variables quantization, are also investigated. Simulation results show that the performance of the uniform quantization scheme is very close to that of the non-quantizaiton over the AWGN channel. Moreover, it can obtain the same performance as that of non-quantization at high SNRs.

Journal of Xidian University•Jan 1, 2004•0 citations

Design and Implementation of Low Bit Error Rate of LDPC Decoder

Ashlesha P. Kshirsagar, Sandeep Kakde, Manish Devendra Chawhan +1 more

Many classes of high-performance Low-density parity check codes are based on parity check matrices composed of permutation sub matrices. The emulation-simulation framework further allows the algorithm and implementation to be iteratively redefined to improve the error floor performance of message passing decoder. Log-Like hood-Ratio (LLR) based Belief-Propagation (BP) algorithm is presented for Low Density Parity Check codes. Numerically accurate representation of check node update computation used in LLR-BP decoding is described. The implementation of Sum-Product algorithm (SPA) within Low Density Parity Check Code (LDPC) decoder is described in this paper and the correction term is used to improve the decoding performance of min-sum algorithm (MSA). Quantization and log-tanh function approximation in sum-product decoder strongly affect which absorbing set dominates in error floor region. For LDPC decoder, bit error rate (BER) decreases with increase in the signal to noise ratio.

International Conference on Communication Systems and Network Technologies•Apr 1, 2015•1 citation

Düşük yoğunluklu eşlik denetim kodları için kod çözme algoritmalarının karşılaştırılması.

Kolaylı, Mert

Low-density parity-check (LDPC) codes are a subclass of linear block codes. These codes have parity-check matrices in which the ratio of the non-zero elements to all elements is low. This property is exploited in defining low complexity decoding algorithms. Low-density parity-check codes have good distance properties and error correction capability near Shannon limits. In this thesis, the sum-product and the bit-flip decoding algorithms for low-density parity-check codes are implemented on Intel Pentium M 1,86 GHz processor using the software called MATLAB. Simulations for the two decoding algorithms are made over additive white gaussian noise (AWGN) channel changing the code parameters like the information rate, the blocklength of the code and the column weight of the parity-check matrix. Performance comparison of the two decoding algorithms are made according to these simulation results. As expected, the sum-product algorithm, which is based on soft-decision decoding, outperforms the bit-flip algorithm, which depends on hard-decision decoding. Our simulations show that the performance of LDPC codes improves with increasing blocklength and number of iterations for both decoding algorithms. Since the sum-product algorithm has lower error-floor characteristics, increasing the number of iterations is more effective for the sum-product decoder compared to the bit-flip decoder. By having better BER performance for lower information rates, the bit-flip algorithm performs according to the expectations; however, the performance of the sum-product decoder deteriorates for information rates below 0.5 instead of improving. By irregular construction of LDPC codes, a performance improvement is observed especially for low SNR values.

•Jan 1, 2006•0 citations

Design and implementation of decoders for error correction in high-speed communication systems.

Joan Marc Català Pérez

This thesis is focused on the design and implementation of binary low-density parity-check (LDPC) code decoders for high-speed modern communication systems. The basic of LDPC codes and the performance and bottlenecks, in terms of complexity and hardware efficiency, of the main soft-decision and hard-decision decoding algorithms (such as Min-Sum, Optimized 2-bit Min-Sum and Reliability-based iterative Majority-Logic) are analyzed. The complexity and performance of those algorithms are improved to allow efficient hardware architectures.\n\nA new decoding algorithm called One-Minimum Min-Sum is proposed. It reduces considerably the complexity of the check node update equations of the Min-Sum algorithm. The second minimum is estimated from the first minimum value by a means of a linear approximation that allows a dynamic adjustment. The Optimized 2-bit Min-Sum algorithm is modified to initialize it with the complete LLR values and to introduce the extrinsic information in the messages sent from the variable nodes. Its variable node equation is reformulated to reduce its complexity. Both algorithms were tested for the (2048,1723) RS-based LDPC code and (16129,15372) LDPC code using an FPGA-based hardware emulator. They exhibit BER performance very close to Min-Sum algorithm and do not introduce early error-floor. \n\nIn order to show the hardware advantages of the proposed algorithms, hardware decoders were implemented in a 90 nm CMOS process and FPGA devices based on two types of architectures: full-parallel and partial-parallel one with horizontal layered schedule. The results show that the decoders are more area-time efficient than other published decoders and that the low-complexity of the Modified Optimized 2-bit Min-Sum allows the implementation of 10 Gbps decoders in current FPGA devices. \n\nFinally, a new hard-decision decoding algorithm, the Historical-Extrinsic Reliability-Based Iterative Decoder, is presented. This algorithm introduces the new idea of considering hard-decision votes as soft-decision to compute the extrinsic information of previous iterations. It is suitable for high-rate codes and improves the BER performance of the previous RBI-MLGD algorithms, with similar complexity.

•Jul 7, 2017•0 citations
of the Dissertation Quantization of a Low-Density Parity-Check (LDPC) Decoder: Limited-Precision Digital Design of the Sum-Product Algorithm (SPA) for Wireless Voice and Video Communication Channels. by Raymond B Moberly Claremont Graduate University and San Diego State University: 2012 This dissertation presents two-bit and three-bit quantizations for Sum Product Algorithm (SPA) decoding of Low-Density Parity-Check (LDPC) codes. The study involves evaluation of both decoding performance and hardware implementation requirements. Trade-o s between these factors are considered. The quantizations are simulated in software to measure decoding performance. While quantization e ects are the focal point of the research, a comparison of the number of decoding iterations and of the number of bits of precision used in the decoder are both presented along with the quantization experiments. Decoder performance, measured in terms of both Bit Error Rate (BER) and Frame Error Rate (FER), is tested for each two-bit and three-bit quantization over a range of Signal to Noise Ratio (SNR) values. No single quantization outperforms all other quantizations for the entire tested SNR range. Analysis of the SPA is performed, revealing strategies for computational e ciency and digital design. The hardware designs combine the parity-check and variable-node update steps of the SPA into a single update computation. The update computation is implemented in a hardware design language (HDL), synthesized to programmable logic, and then tested on a Field Programmable Gate Array (FPGA). Hardware implementation requirements, as measured from the synthesis results, are evaluated and compared to a selection of other published works, particularly the work of Planjery et al. A exible implementation is proposed that can adapt the quantization as the channel conditions change.
A variable step uniform quantization(VSUQ) sum-product algorithm(SPA) was developed to reduce the hardware complexity of low-density parity-check(LDPC) code decoding.The extrinsic information in the check nodes and bit nodes is quantized in the same quantization step.Then,the quantization steps for the check nodes and bit nodes are multiplied and divided by a predetermined parameter.Simulation and implementation using a field programmable gate array(FPGA) show that the performance degradation in the algorithm is within 0.1 dB comparing to the unquantized standard SPA,while reducing the hardware size by 50% comparing to a uniform quantization SPA with the same performance.
In this paper, we propose low complexity implementations of sum-product algorithm (SPA) for decoding low-density parity-check (LDPC) codes. The finite precision implementations for SPA have an important tradeoff between the decoding performance and hardware complexity caused by two dominant area consuming factors. One is the memory for updated messages storage and the other is the look-up table (LUT) for implementation of nonlinear function Psi(x). The proposed two types of variable quantization schemes result in significant reductions of LUT sizes. Computer simulation results indicate that the performance losses of SPA with reduced LUT by proposed schemes are less than 0.05 dB compared to that of SPA with original LUT. Moreover, the proposed implementation offers a large reduction in the finite wordlength for storage of updated messages using a kind of compression technique without performance losses. As a result, using the proposed implementation based on variable quantization scheme and data compression technique, the novel proposed implementation for SPA decoder architecture offers significant reductions of 75% and 33% in hardware complexities of LUT and memories, respectively, without significant performance degradations over conventional uniform quantization scheme. Furthermore, since each LUT with variable (6:3) quantization scheme II has only 8 entries, its hardware implementation can be replaced with a small combination circuit instead of readonly-memory (ROM) for LUT
An efficient implementation of the Sum-Product algorithm(SPA) in the log-likelihood ratio (LLR) domain is presented in [1]. In this paper, We modify a formula in [1] such that SPA can be implemented by using two small look-up tables. With this modification, all the calculations involved in this implementation involve only additions, subtractions, comparisons and table looking-ups, which leads to low computation complexity and facility in hardware implementation. Based on this modified implementation, various quantization schemes of SPA for decoding low-density parity-check (LDPC) codes are investigated. And the issues related to quantization, such as clipping levels and variables quantization, are also investigated. Simulation results show that the performance of the uniform quantization scheme is very close to that of the non-quantizaiton over the AWGN channel. Moreover, it can obtain the same performance as that of non-quantization at high SNRs.
Many classes of high-performance Low-density parity check codes are based on parity check matrices composed of permutation sub matrices. The emulation-simulation framework further allows the algorithm and implementation to be iteratively redefined to improve the error floor performance of message passing decoder. Log-Like hood-Ratio (LLR) based Belief-Propagation (BP) algorithm is presented for Low Density Parity Check codes. Numerically accurate representation of check node update computation used in LLR-BP decoding is described. The implementation of Sum-Product algorithm (SPA) within Low Density Parity Check Code (LDPC) decoder is described in this paper and the correction term is used to improve the decoding performance of min-sum algorithm (MSA). Quantization and log-tanh function approximation in sum-product decoder strongly affect which absorbing set dominates in error floor region. For LDPC decoder, bit error rate (BER) decreases with increase in the signal to noise ratio.
Low-density parity-check (LDPC) codes are a subclass of linear block codes. These codes have parity-check matrices in which the ratio of the non-zero elements to all elements is low. This property is exploited in defining low complexity decoding algorithms. Low-density parity-check codes have good distance properties and error correction capability near Shannon limits. In this thesis, the sum-product and the bit-flip decoding algorithms for low-density parity-check codes are implemented on Intel Pentium M 1,86 GHz processor using the software called MATLAB. Simulations for the two decoding algorithms are made over additive white gaussian noise (AWGN) channel changing the code parameters like the information rate, the blocklength of the code and the column weight of the parity-check matrix. Performance comparison of the two decoding algorithms are made according to these simulation results. As expected, the sum-product algorithm, which is based on soft-decision decoding, outperforms the bit-flip algorithm, which depends on hard-decision decoding. Our simulations show that the performance of LDPC codes improves with increasing blocklength and number of iterations for both decoding algorithms. Since the sum-product algorithm has lower error-floor characteristics, increasing the number of iterations is more effective for the sum-product decoder compared to the bit-flip decoder. By having better BER performance for lower information rates, the bit-flip algorithm performs according to the expectations; however, the performance of the sum-product decoder deteriorates for information rates below 0.5 instead of improving. By irregular construction of LDPC codes, a performance improvement is observed especially for low SNR values.
This thesis is focused on the design and implementation of binary low-density parity-check (LDPC) code decoders for high-speed modern communication systems. The basic of LDPC codes and the performance and bottlenecks, in terms of complexity and hardware efficiency, of the main soft-decision and hard-decision decoding algorithms (such as Min-Sum, Optimized 2-bit Min-Sum and Reliability-based iterative Majority-Logic) are analyzed. The complexity and performance of those algorithms are improved to allow efficient hardware architectures.\n\nA new decoding algorithm called One-Minimum Min-Sum is proposed. It reduces considerably the complexity of the check node update equations of the Min-Sum algorithm. The second minimum is estimated from the first minimum value by a means of a linear approximation that allows a dynamic adjustment. The Optimized 2-bit Min-Sum algorithm is modified to initialize it with the complete LLR values and to introduce the extrinsic information in the messages sent from the variable nodes. Its variable node equation is reformulated to reduce its complexity. Both algorithms were tested for the (2048,1723) RS-based LDPC code and (16129,15372) LDPC code using an FPGA-based hardware emulator. They exhibit BER performance very close to Min-Sum algorithm and do not introduce early error-floor. \n\nIn order to show the hardware advantages of the proposed algorithms, hardware decoders were implemented in a 90 nm CMOS process and FPGA devices based on two types of architectures: full-parallel and partial-parallel one with horizontal layered schedule. The results show that the decoders are more area-time efficient than other published decoders and that the low-complexity of the Modified Optimized 2-bit Min-Sum allows the implementation of 10 Gbps decoders in current FPGA devices. \n\nFinally, a new hard-decision decoding algorithm, the Historical-Extrinsic Reliability-Based Iterative Decoder, is presented. This algorithm introduces the new idea of considering hard-decision votes as soft-decision to compute the extrinsic information of previous iterations. It is suitable for high-rate codes and improves the BER performance of the previous RBI-MLGD algorithms, with similar complexity.