Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Microwave and Guided Wave Letters

Propagation characteristics of monolithic YBaCuO coplanar strip transmission lines fabricated by laser-writing patterning technique

Win Naing Maung, Donald P. Butler, W. Xiong, Witold Kula, Roman Sobolewski

Published May 1, 1994• 3 citations
Publisher

Abstract

We report our studies on the propagation characteristics of YBa/sub 2/Cu/sub 3/O/sub 7/-on-LaAlO/sub 3/ superconducting coplanar strip transmission lines and resonators fabricated with a novel laser-writing patterning technique. The measurements were performed in the 0.1 to 15 GHz frequency range at temperatures between 300 and 24 K. We show that at temperatures below the superconducting critical temperature, the S/sub 21/ parameter of our transmission lines was close to 0 dB at all the frequencies, while the Q-factor of the resonator structure was as high as 5000 at 6 GHz and 24 K. The transmission line propagation velocity was about 10/sup 8/ cm/s. Our results indicate that the laser-writing patterning technique can be effectively used to fabricate high-quality superconducting microwave elements and circuits.>

DOI
10.1109/75.289519

Related papers

Loss Dependence on Geometry and Applied Power in Superconducting Coplanar Resonators

Moe S. Khalil, F. C. Wellstood, Kevin D. Osborn

The loss in superconducting microwave resonators at low-photon numbers and low temperatures is not well understood but has implications for achievable coherence times in superconducting qubits. We have fabricated single-layer resonators with a high quality factor by patterning a superconducting aluminum film on a sapphire substrate. Four resonator geometries were studied with resonant frequencies ranging from 5 to 7 GHz: a quasi-lumped element resonator, a coplanar strip waveguide resonator, and two hybrid designs that contain both a coplanar strip and a quasi-lumped element. Transmitted power measurements were taken at 30 mK as a function of frequency and probe power. We find that the resonator loss, expressed as the inverse of the internal quality factor, decreases slowly over four decades of photon number in a manner not merely explained by loss from a conventional uniform spatial distribution of two-level systems in an oxide layer on the superconducting surfaces of the resonator.

arXiv:1008.2929•IEEE Transactions on Applied Superconductivity•Dec 9, 2010•69 citations

Modulation of the resonance frequency of superconducting microwave resonators

Shinho Cho, Chang-Sik Son Chang-Sik Son

The microwave transmission characteristics of superconducting YBa/sub 2/Cu/sub 3/O/sub 7-x/ (YBCO) meander line resonators have been investigated as a function of temperature, optical pulse energy, and input power. The measurements are performed in a temperature range from 20 K to 80 K. The optical excitation consists of a 70 psec laser pulse train at 532 nm from an actively mode-locked Nd:YAG laser. The optical pulse energy is mapped out from zero to the critical optical pulse energy at which the resonance can no longer be distinguished. The measured resonance frequency shows a squared dependence on both the temperature and the optical pulse energy. As for the dependence on input power, the resonant frequency linearly decreases at a rate of 148 kHz/dBm at 50 K.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•6 citations

Experimental Characterization of Optically Tunable High-Temperature Superconducting Microwave Resonators and Delay Lines

Haig A. Atikian, Behnood G. Ghamsari, A. Hamed Majedi

This paper reports the design, fabrication, and measurements of optically tunable superconducting microwave resonators and delay lines. The devices are comprised of superconducting coplanar waveguide (CPW) transmission lines fabricated from a 100 nm-thick YBCO film, interrupted by 3- and 5-m YBCO meander structures of the same thickness on top of an LAO substrate. The CPW is tested at 77 K up to a frequency of 50 GHz, where it exhibits a transmission loss of about 0.12 dB/mm. The measurements are done in a cryogenic microwave probe station, where all the calibrations have been performed at 77 K. It has been observed that the resonance frequencies of the superconducting resonators can be changed by more than 2 GHz under the optical illumination at a wavelength of 1550 nm. The delay lines also exhibit a phase retardation of up to 90 at the same operating conditions.

IEEE Transactions on Microwave Theory and Techniques•Oct 27, 2010•13 citations

Scattering parameter and bit error rate characterization of high temperature superconducting coplanar transmission lines

J. Kruse, W.H. Chang, D.R. Scherrer +5 more

We report the gigahertz experimental results of time and frequency performance on YBCO high temperature superconductor (HTS) and gold coplanar transmission lines. An on-wafer direct probing measurement system was used to collect data at cryogenic temperatures on both YBCO and gold coplanar lines. The insertion loss of the 6-cm lines at a frequency of 3.0 GHz was measured to be -0.12 dB for the superconducting line compared to -10.7 dB for the gold line at 80 K. Error rate and eye-diagram measurements were performed on the packaged lines and show the correlation between the insertion loss of the line and the attenuation of a Pseudo Random Bit Sequence (PBRS). The superconducting line measured at 77 K had a BER rate of less than 10/sup -11/ at a data rate of 3 Gb/s. The measured eye height was 350 mV for the YBCO compared to 100 mV for a gold line at 3 Gb/s and a temperature of 77 K for the packaged 6-cm lines.

IEEE Transactions on Applied Superconductivity•Jan 1, 1995•0 citations

Planar superconducting YBCO microwave mixer employing an engineered grain boundary weak link junction

R. Seed, Paul C. Dorsey, Hoton How +2 more

A microstrip transmission line was patterned from a superconducting YBa/sub 2/Cu/sub 3/O/sub 7-x/ film which was laser deposited on a SrTiO/sub 3/ bicrystal substrate. A microbridge in the microstrip was then patterned at the bicrystal interface to fabricate a superconducting grain boundary junction. Microwave mixing was observed with an input local oscillator frequency of 9.000 GHz, and an input signal frequency of 9.941 GHz. The output signal at 941 MHz was detected as a transmitted signal. The junction was current biased slightly above the critical current I/sub c/. The measured conversion loss was compared to the calculated value based upon a numerical solution of the equation for a superconducting weak link junction.>

IEEE Transactions on Applied Superconductivity•Jan 1, 1994•6 citations

Superconducting coplanar waveguide resonators for detector applications

G. Hammer, S. Wünsch, M. Roesch +3 more

The use of a transmission line resonator offers the possibility for different sensor readout methods, e.g. flux qubit and kinetic inductance detectors. Both cases require a high quality factor, Q L , of the cavity circuit to detect small deviations in the resonance frequency. Various superconducting niobium coplanar waveguide resonators of λ/4 and λ/2 wavelength for 3 and 6 GHz were developed. Different layouts for the coplanar resonators were designed, simulated and measured on common silicon and sapphire substrates at 4.2 K. We found a very good agreement between simulation and measurement results, with Q L between 10 4 and 10 5 at helium temperatures. The presented results show the dependences on the chosen cross section geometries, the coupling factor and the complex layout of the transmission line.

Superconductor Science and Technology•Oct 18, 2007•19 citations
We report our studies on the propagation characteristics of YBa/sub 2/Cu/sub 3/O/sub 7/-on-LaAlO/sub 3/ superconducting coplanar strip transmission lines and resonators fabricated with a novel laser-writing patterning technique. The measurements were performed in the 0.1 to 15 GHz frequency range at temperatures between 300 and 24 K. We show that at temperatures below the superconducting critical temperature, the S/sub 21/ parameter of our transmission lines was close to 0 dB at all the frequencies, while the Q-factor of the resonator structure was as high as 5000 at 6 GHz and 24 K. The transmission line propagation velocity was about 10/sup 8/ cm/s. Our results indicate that the laser-writing patterning technique can be effectively used to fabricate high-quality superconducting microwave elements and circuits.>
The loss in superconducting microwave resonators at low-photon numbers and low temperatures is not well understood but has implications for achievable coherence times in superconducting qubits. We have fabricated single-layer resonators with a high quality factor by patterning a superconducting aluminum film on a sapphire substrate. Four resonator geometries were studied with resonant frequencies ranging from 5 to 7 GHz: a quasi-lumped element resonator, a coplanar strip waveguide resonator, and two hybrid designs that contain both a coplanar strip and a quasi-lumped element. Transmitted power measurements were taken at 30 mK as a function of frequency and probe power. We find that the resonator loss, expressed as the inverse of the internal quality factor, decreases slowly over four decades of photon number in a manner not merely explained by loss from a conventional uniform spatial distribution of two-level systems in an oxide layer on the superconducting surfaces of the resonator.
The microwave transmission characteristics of superconducting YBa/sub 2/Cu/sub 3/O/sub 7-x/ (YBCO) meander line resonators have been investigated as a function of temperature, optical pulse energy, and input power. The measurements are performed in a temperature range from 20 K to 80 K. The optical excitation consists of a 70 psec laser pulse train at 532 nm from an actively mode-locked Nd:YAG laser. The optical pulse energy is mapped out from zero to the critical optical pulse energy at which the resonance can no longer be distinguished. The measured resonance frequency shows a squared dependence on both the temperature and the optical pulse energy. As for the dependence on input power, the resonant frequency linearly decreases at a rate of 148 kHz/dBm at 50 K.
This paper reports the design, fabrication, and measurements of optically tunable superconducting microwave resonators and delay lines. The devices are comprised of superconducting coplanar waveguide (CPW) transmission lines fabricated from a 100 nm-thick YBCO film, interrupted by 3- and 5-m YBCO meander structures of the same thickness on top of an LAO substrate. The CPW is tested at 77 K up to a frequency of 50 GHz, where it exhibits a transmission loss of about 0.12 dB/mm. The measurements are done in a cryogenic microwave probe station, where all the calibrations have been performed at 77 K. It has been observed that the resonance frequencies of the superconducting resonators can be changed by more than 2 GHz under the optical illumination at a wavelength of 1550 nm. The delay lines also exhibit a phase retardation of up to 90 at the same operating conditions.
We report the gigahertz experimental results of time and frequency performance on YBCO high temperature superconductor (HTS) and gold coplanar transmission lines. An on-wafer direct probing measurement system was used to collect data at cryogenic temperatures on both YBCO and gold coplanar lines. The insertion loss of the 6-cm lines at a frequency of 3.0 GHz was measured to be -0.12 dB for the superconducting line compared to -10.7 dB for the gold line at 80 K. Error rate and eye-diagram measurements were performed on the packaged lines and show the correlation between the insertion loss of the line and the attenuation of a Pseudo Random Bit Sequence (PBRS). The superconducting line measured at 77 K had a BER rate of less than 10/sup -11/ at a data rate of 3 Gb/s. The measured eye height was 350 mV for the YBCO compared to 100 mV for a gold line at 3 Gb/s and a temperature of 77 K for the packaged 6-cm lines.
A microstrip transmission line was patterned from a superconducting YBa/sub 2/Cu/sub 3/O/sub 7-x/ film which was laser deposited on a SrTiO/sub 3/ bicrystal substrate. A microbridge in the microstrip was then patterned at the bicrystal interface to fabricate a superconducting grain boundary junction. Microwave mixing was observed with an input local oscillator frequency of 9.000 GHz, and an input signal frequency of 9.941 GHz. The output signal at 941 MHz was detected as a transmitted signal. The junction was current biased slightly above the critical current I/sub c/. The measured conversion loss was compared to the calculated value based upon a numerical solution of the equation for a superconducting weak link junction.>
The use of a transmission line resonator offers the possibility for different sensor readout methods, e.g. flux qubit and kinetic inductance detectors. Both cases require a high quality factor, Q L , of the cavity circuit to detect small deviations in the resonance frequency. Various superconducting niobium coplanar waveguide resonators of λ/4 and λ/2 wavelength for 3 and 6 GHz were developed. Different layouts for the coplanar resonators were designed, simulated and measured on common silicon and sapphire substrates at 4.2 K. We found a very good agreement between simulation and measurement results, with Q L between 10 4 and 10 5 at helium temperatures. The presented results show the dependences on the chosen cross section geometries, the coupling factor and the complex layout of the transmission line.