Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

New microwave circuits for programmable voltage standards using high-temperature Josephson junction arrays

Alexander M. Klushin, C. Weber, H. Kohlstedt, R.K. Starodubrovskii, A. Lauer, I. Wolff, R. Semerad

Published Jun 1, 1999• 14 citations
Publisher

Abstract

New microwave circuits for voltage standard application containing 256 shunted bicrystal junctions were designed and investigated. The series array follows a meander line, which prevents the uniform distribution of microwave current along the array. To overcome this drawback, we are placing the meander parallel to a coplanar waveguide line. This provides parallel feeding of microwave power to series connected junctions. A circuit divided in 8 sub-arrays represents a seven-bit digital-to-analog converter. At a frequency f=27332 MHz and for a constant power each of the segments of the array demonstrated the first current step at 78 K.

DOI
10.1109/77.783941

Related papers

Integrated microwave circuits for digital-to-analogue converters based on high-temperature superconducting Josephson junction arrays

Alexander M. Klushin, C. Weber, M. Siegel +5 more

A digital-to-analogue converter based on series arrays of high-temperature superconducting Josephson junctions can work properly when the microwave bias current distribution in large arrays is uniform. Unfortunately, the considerable microwave attenuation per overdamped junction with normal resistances RN0.1 results in a strong total attenuation of the microwave signal in a traditional layout. Also, the meander geometry of the array, necessary when using bicrystal junctions, disturbs the uniformity of the rf current, especially in the millimetre waveband. To overcome these drawbacks we coupled the meander array inductively to a parallel transmission line. The mechanism of microwave coupling in which both external and mutual frequency locking takes place was studied numerically. A circuit with a coplanar waveguide feed line was fabricated and successfully tested at an operating frequency of 30 GHz. A microstrip line with a small attenuation for pumping of junction arrays at frequencies up to 120 GHz was demonstrated.

Superconductor Science and Technology•Nov 1, 1999•2 citations

Superconductor-normal-superconductor junctions for programmable voltage standards

S. P. Benz

Series arrays of Nb–PdAu–Nb Josephson junctions were fabricated with characteristics ideally suited for application in programmable voltage standards and D/A converters with fundamental accuracy. Large arrays of junctions with applied microwave power showed constant voltage steps with current amplitudes as large as 7 mA. A novel coplanar waveguide design enabled uniform microwave power coupling to a five-segment array of 8192 junctions, so each segment had constant voltage steps over the same bias range. The 8192-junction device generated 1.1 mA steps at 186 mV with 11 GHz power and a maximum constant voltage step of 260 mV at 15.34 GHz.

Applied Physics Letters•Oct 30, 1995•133 citations

Improved design of superconductor/normal conductor/superconductor Josephson junction series arrays for an ac Josephson voltage standard

Oliver Kieler, J. Kohlmann, Franz Müller

Superconductor/normal conductor/superconductor (SNS) Josephson junction series arrays are the subject of research for the realization of a Josephson arbitrary waveform synthesizer (JAWS) based on pulse-driven Josephson junctions. Lumped arrays of SNS Josephson junctions are investigated for this application at the Physikalisch-Technische Bundesanstalt (PTB). The series arrays consisting of Nb/HfTi/Nb SNS junctions are embedded in the center line of a coplanar waveguide transmission line. To increase the ac output voltage, the Josephson junction series array is designed as a meander-like structure. A broadband response of the arrays is required for the complex pulse operation of the JAWS. The arrays are investigated by dc measurements and for test purposes under continuous microwave irradiation at different frequencies. Flat Shapiro steps were measured for meander-like series arrays with 21 parallel lines containing up to 10 752 junctions. A sine wave with a frequency of 2.5 kHz and a peak voltage of 214 mV Peak was synthesized under pulse mode operation.

Superconductor Science and Technology•Oct 18, 2007•28 citations

Coplanar strips for Josephson voltage standard circuits

M. Schubert, T. May, G. Wende +2 more

We present a microwave circuit for Josephson voltage standards. Here, the Josephson junctions are integrated in a microwave transmission line designed as coplanar strips (CPS). The new layout offers the possibility of achieving a higher scale of integration and to considerably simplify the fabrication technology. The characteristic impedance of the CPS is about 50 Ω, and this should be of interest for programmable Josephson voltage standard circuits with SNS or SINIS junctions. To demonstrate the function of the microwave circuit design, conventional 10 V Josephson voltage standard circuits with 17 000 Nb/AlOx/Nb junctions were prepared and tested. Stable Shapiro steps at the 10 V level were generated. Furthermore, arrays of 1400 SINIS junctions in this microwave layout exhibited first-order Shapiro steps.

Applied Physics Letters•Aug 13, 2001•22 citations

Fabrication of Voltage Standard Circuits Utilizing a Serial–Parallel Power Divider

Hirotake Yamamori, Satoshi Kohjiro

Digital-to-analog converter circuits utilizing NbTiN/Ti-TiN/NbTiN Josephson junctions were fabricated as quantum voltage standards, and were evaluated at around 10 K in a cryocooler. The first Shapiro step was generated at 2 V and had a height of more than 0.5 mA. Instead of a conventional microwave power divider that uses a quarter-wavelength resonator, a serial-parallel power divider was employed. This consisted of coplanar waveguides connected in parallel and coplanar strips connected in series. As a result, the chip area for the power divider was reduced by about 70%, and uniform frequency characteristics for the operating current margin were obtained.

IEEE Transactions on Applied Superconductivity•Oct 27, 2016•8 citations

Microwave optimization of 10 V PJVS circuits

Paul D. Dresselhaus, Mike Elsbury, Charles J. Burroughs +1 more

Proper operation of programmable Josephson voltage standard arrays depends on the uniform distribution of microwaves to a large number of Josephson junctions. Too much or too little microwave power will change the current range of a junction's constant voltage step so that an entire array of junctions will have a smaller total current margin. In this paper we discuss the important aspects of microwave power distribution including splitting the microwaves to different arrays, keeping the microwave bias uniform within an array, and minimizing the total input power to the circuit.

•Jun 1, 2010•1 citation
New microwave circuits for voltage standard application containing 256 shunted bicrystal junctions were designed and investigated. The series array follows a meander line, which prevents the uniform distribution of microwave current along the array. To overcome this drawback, we are placing the meander parallel to a coplanar waveguide line. This provides parallel feeding of microwave power to series connected junctions. A circuit divided in 8 sub-arrays represents a seven-bit digital-to-analog converter. At a frequency f=27332 MHz and for a constant power each of the segments of the array demonstrated the first current step at 78 K.
A digital-to-analogue converter based on series arrays of high-temperature superconducting Josephson junctions can work properly when the microwave bias current distribution in large arrays is uniform. Unfortunately, the considerable microwave attenuation per overdamped junction with normal resistances RN0.1 results in a strong total attenuation of the microwave signal in a traditional layout. Also, the meander geometry of the array, necessary when using bicrystal junctions, disturbs the uniformity of the rf current, especially in the millimetre waveband. To overcome these drawbacks we coupled the meander array inductively to a parallel transmission line. The mechanism of microwave coupling in which both external and mutual frequency locking takes place was studied numerically. A circuit with a coplanar waveguide feed line was fabricated and successfully tested at an operating frequency of 30 GHz. A microstrip line with a small attenuation for pumping of junction arrays at frequencies up to 120 GHz was demonstrated.
Series arrays of Nb–PdAu–Nb Josephson junctions were fabricated with characteristics ideally suited for application in programmable voltage standards and D/A converters with fundamental accuracy. Large arrays of junctions with applied microwave power showed constant voltage steps with current amplitudes as large as 7 mA. A novel coplanar waveguide design enabled uniform microwave power coupling to a five-segment array of 8192 junctions, so each segment had constant voltage steps over the same bias range. The 8192-junction device generated 1.1 mA steps at 186 mV with 11 GHz power and a maximum constant voltage step of 260 mV at 15.34 GHz.
Superconductor/normal conductor/superconductor (SNS) Josephson junction series arrays are the subject of research for the realization of a Josephson arbitrary waveform synthesizer (JAWS) based on pulse-driven Josephson junctions. Lumped arrays of SNS Josephson junctions are investigated for this application at the Physikalisch-Technische Bundesanstalt (PTB). The series arrays consisting of Nb/HfTi/Nb SNS junctions are embedded in the center line of a coplanar waveguide transmission line. To increase the ac output voltage, the Josephson junction series array is designed as a meander-like structure. A broadband response of the arrays is required for the complex pulse operation of the JAWS. The arrays are investigated by dc measurements and for test purposes under continuous microwave irradiation at different frequencies. Flat Shapiro steps were measured for meander-like series arrays with 21 parallel lines containing up to 10 752 junctions. A sine wave with a frequency of 2.5 kHz and a peak voltage of 214 mV Peak was synthesized under pulse mode operation.
We present a microwave circuit for Josephson voltage standards. Here, the Josephson junctions are integrated in a microwave transmission line designed as coplanar strips (CPS). The new layout offers the possibility of achieving a higher scale of integration and to considerably simplify the fabrication technology. The characteristic impedance of the CPS is about 50 Ω, and this should be of interest for programmable Josephson voltage standard circuits with SNS or SINIS junctions. To demonstrate the function of the microwave circuit design, conventional 10 V Josephson voltage standard circuits with 17 000 Nb/AlOx/Nb junctions were prepared and tested. Stable Shapiro steps at the 10 V level were generated. Furthermore, arrays of 1400 SINIS junctions in this microwave layout exhibited first-order Shapiro steps.
Digital-to-analog converter circuits utilizing NbTiN/Ti-TiN/NbTiN Josephson junctions were fabricated as quantum voltage standards, and were evaluated at around 10 K in a cryocooler. The first Shapiro step was generated at 2 V and had a height of more than 0.5 mA. Instead of a conventional microwave power divider that uses a quarter-wavelength resonator, a serial-parallel power divider was employed. This consisted of coplanar waveguides connected in parallel and coplanar strips connected in series. As a result, the chip area for the power divider was reduced by about 70%, and uniform frequency characteristics for the operating current margin were obtained.
Proper operation of programmable Josephson voltage standard arrays depends on the uniform distribution of microwaves to a large number of Josephson junctions. Too much or too little microwave power will change the current range of a junction's constant voltage step so that an entire array of junctions will have a smaller total current margin. In this paper we discuss the important aspects of microwave power distribution including splitting the microwaves to different arrays, keeping the microwave bias uniform within an array, and minimizing the total input power to the circuit.