Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Microwave optimization of 10 V PJVS circuits

Paul D. Dresselhaus, Mike Elsbury, Charles J. Burroughs, Samuel P. Benz

Published Jun 1, 2010• 1 citation
Publisher

Abstract

Proper operation of programmable Josephson voltage standard arrays depends on the uniform distribution of microwaves to a large number of Josephson junctions. Too much or too little microwave power will change the current range of a junction's constant voltage step so that an entire array of junctions will have a smaller total current margin. In this paper we discuss the important aspects of microwave power distribution including splitting the microwaves to different arrays, keeping the microwave bias uniform within an array, and minimizing the total input power to the circuit.

DOI
10.1109/cpem.2010.5543823

Related papers

10 Volt Programmable Josephson Voltage Standard Circuits Using NbSi-Barrier Junctions

Paul D. Dresselhaus, Michael M. Elsbury, David I. Olaya +2 more

Programmable Josephson voltage standard (PJVS) circuits were developed that operate at 16 GHz to 20 GHz with operating margins larger than 1 mA. Two circuit designs were demonstrated, each having a total of ~ 300,000 junctions, which were divided into either 16 or 32 sub-arrays. Triple-stacked junctions were used in order to fit the ~300,000 junctions on each circuit. The amorphous NbxSi1-x-barrier junction technology provided a high degree of uniformity of the barrier and junction electrical properties, which was necessary to achieve the 1 mA operating margin. Although the margins on both the 16-array and 32-array circuits were much greater than 1 mA, the circuit yield for the 16-array design was lower because the longer arrays are more sensitive to defects. The use of lumped-element microwave splitters and tapered arrays significantly reduced the microwave input power and increased the operating margins of these designs. In addition, the broadband microwave response of the designs allowed the PJVS output voltage to be continuously adjusted by using the microwave frequency while remaining on margins.

IEEE Transactions on Applied Superconductivity•Nov 9, 2010•59 citations

Design of a turn-key 10 V Programmable Josephson Voltage Standard system

Paul D. Dresselhaus, Michael M. Elsbury, Charles J. Burroughs +5 more

NIST is designing a 10 V Programmable Josephson Voltage Standard (PJVS) system with an improved microwave design and arrays of stacked NbxSi1-x-barrier Josephson junctions. For this new design a "ground-up" approach was used that takes into account all system issues in order to produce a robust 10 V system. By improving the uniformity of the microwave drive along the length of each array, constant-voltage steps with a larger current range are generated allowing the use of smaller critical current junctions. Smaller critical currents are important for lowering the total overall power dissipated on chip. Reducing power dissipation also increases the operating margins. Thus, all aspects of the design are interrelated and important for an optimized system.

Conference on Precision Electromagnetic Measurements•Jun 1, 2008•4 citations

Microwave Design and Performance of PTB 10 V Circuits for the Programmable Josephson Voltage Standard

Franz Müller, Thomas Scheller, Jinni Lee +4 more

At Physikalisch-Technische Bundesanstalt (PTB), superconducting 10 V circuits for the programmable Josephson voltage standard (PJVS) are routinely manufactured on the basis of NbxSi1-x barrier junctions. This paper describes in detail the basic design principles for an operating frequency of 70 GHz. It starts with single junctions, discusses their insertion into microstriplines and closes with the whole microwave circuit containing 69,632 NbxSi1-x barrier junctions arranged over 128 microstriplines connected in parallel. The microwave attenuation of this junction type is a key parameter for the 10 V design and we report its experimental determination. Special attention has been devoted to subarrays with just a few Josephson junctions in one of the outermost striplines. The arrangement of these subarrays determines the optimum performance of the complete 10 V series array. The high performance of programmable 10 V circuits fabricated at PTB is characterized by measured operating margins in all subarrays of more than 1 mA centered at the same dc bias current. The observed modulation of the current margins, when changing the frequency around 70 GHz, is explained by microwave reflections caused by the rf waveguide inside the cryoprobe. We determine the current margins in dependence of the output power of a microwave synthesizer and show that 60 mW is sufficient to achieve current margins larger than 1 mA.

World Journal of Condensed Matter Physics•Jan 1, 2014•20 citations

A 10 V programmable Josephson voltage standard circuit with a maximum output voltage of 20 V

Hirotake Yamamori, Takahiro Yamada, Hitoshi Sasaki +1 more

A 10 V programmable Josephson voltage standard (PJVS) circuit with a maximum output voltage of 20 V and a microwave bias of 18.5 GHz was designed and fabricated. Although an attempt was made to improve the fabrication yield for the 10 V PJVS circuit, it was not sufficiently large to reproducibly fabricate a perfect chip without any defects. The redundant arrays were additionally integrated to increase the maximum output voltage, which contributed to an increase in the number of available chips under the limited fabrication yield. Fortunately, most of the defective arrays had a zeroth Shapiro step, while the first step was very small or zero. If the array was not dc biased, it did not generate any voltage, because it worked as a superconductive wiring. In this case, the maximum output voltage became smaller than that of a perfect chip, but it functioned as a 10 V PJVS, due to the back-up arrays.

Superconductor Science and Technology•Jul 23, 2008•58 citations

Programmable Josephson Voltage Standard Circuits Using Arrays of NbN/TiN/NbN/TiN/NbN Double-Junction Stacks Operated at 10 K

Mayumi Ishizaki, Hirotake Yamamori, Alexandre Shoji +2 more

Programmable Josephson voltage standard (PJVS) circuits using arrays of NbN/TiN/NbN/TiN/NbN double-junction stacks were fabricated and operated at a temperature of 10 K. Four arrays each with 32 768 junctions produced expected voltage outputs when driven at (10, 15, 17, and 20) GHz with an operating current range of 0.2-1.0 mA. Another circuit showed constant-voltage steps at /spl plusmn/6 V when driven with an 11 GHz microwave bias, indicating that over 260 000 junctions were operating properly. This circuit did not show constant-voltage steps when driven with a 19 GHz microwave bias, which was the design frequency to achieve /spl plusmn/10 V output voltage.

IEEE Transactions on Instrumentation and Measurement•Mar 21, 2005•11 citations

New microwave circuits for programmable voltage standards using high-temperature Josephson junction arrays

Alexander M. Klushin, C. Weber, H. Kohlstedt +4 more

New microwave circuits for voltage standard application containing 256 shunted bicrystal junctions were designed and investigated. The series array follows a meander line, which prevents the uniform distribution of microwave current along the array. To overcome this drawback, we are placing the meander parallel to a coplanar waveguide line. This provides parallel feeding of microwave power to series connected junctions. A circuit divided in 8 sub-arrays represents a seven-bit digital-to-analog converter. At a frequency f=27332 MHz and for a constant power each of the segments of the array demonstrated the first current step at 78 K.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•14 citations
Proper operation of programmable Josephson voltage standard arrays depends on the uniform distribution of microwaves to a large number of Josephson junctions. Too much or too little microwave power will change the current range of a junction's constant voltage step so that an entire array of junctions will have a smaller total current margin. In this paper we discuss the important aspects of microwave power distribution including splitting the microwaves to different arrays, keeping the microwave bias uniform within an array, and minimizing the total input power to the circuit.
Programmable Josephson voltage standard (PJVS) circuits were developed that operate at 16 GHz to 20 GHz with operating margins larger than 1 mA. Two circuit designs were demonstrated, each having a total of ~ 300,000 junctions, which were divided into either 16 or 32 sub-arrays. Triple-stacked junctions were used in order to fit the ~300,000 junctions on each circuit. The amorphous NbxSi1-x-barrier junction technology provided a high degree of uniformity of the barrier and junction electrical properties, which was necessary to achieve the 1 mA operating margin. Although the margins on both the 16-array and 32-array circuits were much greater than 1 mA, the circuit yield for the 16-array design was lower because the longer arrays are more sensitive to defects. The use of lumped-element microwave splitters and tapered arrays significantly reduced the microwave input power and increased the operating margins of these designs. In addition, the broadband microwave response of the designs allowed the PJVS output voltage to be continuously adjusted by using the microwave frequency while remaining on margins.
NIST is designing a 10 V Programmable Josephson Voltage Standard (PJVS) system with an improved microwave design and arrays of stacked NbxSi1-x-barrier Josephson junctions. For this new design a "ground-up" approach was used that takes into account all system issues in order to produce a robust 10 V system. By improving the uniformity of the microwave drive along the length of each array, constant-voltage steps with a larger current range are generated allowing the use of smaller critical current junctions. Smaller critical currents are important for lowering the total overall power dissipated on chip. Reducing power dissipation also increases the operating margins. Thus, all aspects of the design are interrelated and important for an optimized system.
At Physikalisch-Technische Bundesanstalt (PTB), superconducting 10 V circuits for the programmable Josephson voltage standard (PJVS) are routinely manufactured on the basis of NbxSi1-x barrier junctions. This paper describes in detail the basic design principles for an operating frequency of 70 GHz. It starts with single junctions, discusses their insertion into microstriplines and closes with the whole microwave circuit containing 69,632 NbxSi1-x barrier junctions arranged over 128 microstriplines connected in parallel. The microwave attenuation of this junction type is a key parameter for the 10 V design and we report its experimental determination. Special attention has been devoted to subarrays with just a few Josephson junctions in one of the outermost striplines. The arrangement of these subarrays determines the optimum performance of the complete 10 V series array. The high performance of programmable 10 V circuits fabricated at PTB is characterized by measured operating margins in all subarrays of more than 1 mA centered at the same dc bias current. The observed modulation of the current margins, when changing the frequency around 70 GHz, is explained by microwave reflections caused by the rf waveguide inside the cryoprobe. We determine the current margins in dependence of the output power of a microwave synthesizer and show that 60 mW is sufficient to achieve current margins larger than 1 mA.
A 10 V programmable Josephson voltage standard (PJVS) circuit with a maximum output voltage of 20 V and a microwave bias of 18.5 GHz was designed and fabricated. Although an attempt was made to improve the fabrication yield for the 10 V PJVS circuit, it was not sufficiently large to reproducibly fabricate a perfect chip without any defects. The redundant arrays were additionally integrated to increase the maximum output voltage, which contributed to an increase in the number of available chips under the limited fabrication yield. Fortunately, most of the defective arrays had a zeroth Shapiro step, while the first step was very small or zero. If the array was not dc biased, it did not generate any voltage, because it worked as a superconductive wiring. In this case, the maximum output voltage became smaller than that of a perfect chip, but it functioned as a 10 V PJVS, due to the back-up arrays.
Programmable Josephson voltage standard (PJVS) circuits using arrays of NbN/TiN/NbN/TiN/NbN double-junction stacks were fabricated and operated at a temperature of 10 K. Four arrays each with 32 768 junctions produced expected voltage outputs when driven at (10, 15, 17, and 20) GHz with an operating current range of 0.2-1.0 mA. Another circuit showed constant-voltage steps at /spl plusmn/6 V when driven with an 11 GHz microwave bias, indicating that over 260 000 junctions were operating properly. This circuit did not show constant-voltage steps when driven with a 19 GHz microwave bias, which was the design frequency to achieve /spl plusmn/10 V output voltage.
New microwave circuits for voltage standard application containing 256 shunted bicrystal junctions were designed and investigated. The series array follows a meander line, which prevents the uniform distribution of microwave current along the array. To overcome this drawback, we are placing the meander parallel to a coplanar waveguide line. This provides parallel feeding of microwave power to series connected junctions. A circuit divided in 8 sub-arrays represents a seven-bit digital-to-analog converter. At a frequency f=27332 MHz and for a constant power each of the segments of the array demonstrated the first current step at 78 K.