Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconductor Science and Technology

A 10 V programmable Josephson voltage standard circuit with a maximum output voltage of 20 V

Hirotake Yamamori, Takahiro Yamada, Hitoshi Sasaki, Akira Shoji

Published Jul 23, 2008• 58 citations
Publisher

Abstract

A 10 V programmable Josephson voltage standard (PJVS) circuit with a maximum output voltage of 20 V and a microwave bias of 18.5 GHz was designed and fabricated. Although an attempt was made to improve the fabrication yield for the 10 V PJVS circuit, it was not sufficiently large to reproducibly fabricate a perfect chip without any defects. The redundant arrays were additionally integrated to increase the maximum output voltage, which contributed to an increase in the number of available chips under the limited fabrication yield. Fortunately, most of the defective arrays had a zeroth Shapiro step, while the first step was very small or zero. If the array was not dc biased, it did not generate any voltage, because it worked as a superconductive wiring. In this case, the maximum output voltage became smaller than that of a perfect chip, but it functioned as a 10 V PJVS, due to the back-up arrays.

DOI
10.1088/0953-2048/21/10/105007

Related papers

Improved Fabrication Yield for 10-V Programmable Josephson Voltage Standard Circuit Including 524288 NbN/TiN/NbN Josephson Junctions

Hirotake Yamamori, Takahiro Yamada, Hitoshi Sasaki +1 more

A 10-V programmable Josephson voltage standard (PJVS) circuit including 524 288 vertically stacked NbN/TiN/NbN Josephson junctions was successfully fabricated without any defects. The chip was cooled with a compact cryocooler at a temperature of 9.8 K and generated an output voltage of 17.3 V with the first Shapiro step height of 1.0 mA under microwave irradiation at 16 GHz. Furthermore, the circuit design having the high output voltage increased the number of available chips for the 10-V PJVS. The fabrication yield for the chip, which generates greater than 10 V, was 36%, which is ten times greater than that for a perfect chip without any defects. This method was not effective for the chip that had serious defects, such as a disconnection across the array or short between the array and ground; thus, efforts to reduce such defects, e.g., frequent maintenance inside vacuum chambers for film preparation and etching, were found to be essential.

IEEE Transactions on Applied Superconductivity•Mar 26, 2010•15 citations

Programmable Josephson Voltage Standard Circuits Using Arrays of NbN/TiN/NbN/TiN/NbN Double-Junction Stacks Operated at 10 K

Mayumi Ishizaki, Hirotake Yamamori, Alexandre Shoji +2 more

Programmable Josephson voltage standard (PJVS) circuits using arrays of NbN/TiN/NbN/TiN/NbN double-junction stacks were fabricated and operated at a temperature of 10 K. Four arrays each with 32 768 junctions produced expected voltage outputs when driven at (10, 15, 17, and 20) GHz with an operating current range of 0.2-1.0 mA. Another circuit showed constant-voltage steps at /spl plusmn/6 V when driven with an 11 GHz microwave bias, indicating that over 260 000 junctions were operating properly. This circuit did not show constant-voltage steps when driven with a 19 GHz microwave bias, which was the design frequency to achieve /spl plusmn/10 V output voltage.

IEEE Transactions on Instrumentation and Measurement•Mar 21, 2005•11 citations

10 Volt Programmable Josephson Voltage Standard Circuits Using NbSi-Barrier Junctions

Paul D. Dresselhaus, Michael M. Elsbury, David I. Olaya +2 more

Programmable Josephson voltage standard (PJVS) circuits were developed that operate at 16 GHz to 20 GHz with operating margins larger than 1 mA. Two circuit designs were demonstrated, each having a total of ~ 300,000 junctions, which were divided into either 16 or 32 sub-arrays. Triple-stacked junctions were used in order to fit the ~300,000 junctions on each circuit. The amorphous NbxSi1-x-barrier junction technology provided a high degree of uniformity of the barrier and junction electrical properties, which was necessary to achieve the 1 mA operating margin. Although the margins on both the 16-array and 32-array circuits were much greater than 1 mA, the circuit yield for the 16-array design was lower because the longer arrays are more sensitive to defects. The use of lumped-element microwave splitters and tapered arrays significantly reduced the microwave input power and increased the operating margins of these designs. In addition, the broadband microwave response of the designs allowed the PJVS output voltage to be continuously adjusted by using the microwave frequency while remaining on margins.

IEEE Transactions on Applied Superconductivity•Nov 9, 2010•59 citations

NbN-Based Overdamped Josephson Junctions for Quantum Voltage Standards

Hirotake Yamamori, Takahiro Yamada, Hitoshi SASAKI +1 more

524,288 NbN-based Josephson junctions were integrated to produce a programmable Josephson voltage standard (PJVS) on a die of 15mm × 15mm, and the PJVS circuit was cooled to 10K using a cryocooler and operated with a current margin of about 1.0mA. Although an output voltage of 10V was required for a voltage standard, the circuit was designed to generate the maximum output voltage of 17V because it was difficult to avoid a reduction of the output voltage due to defects. Although a perfect chip without any defect was rarely fabricated, the high voltage chip that generated at least 10V was fabricated with the fabrication yield of larger than 30%. The fabrication yield was also improved by optimizing the film growth conditions to reduce the film stress and the number of particles. Applications for a secondary voltage standard and an ac Josephson voltage standard are also described.

IEICE Transactions on Electronics•Jan 1, 2012•24 citations

Improved 10 V SINIS Series Arrays for Applications in AC Voltage Metrology

F.. Mueller, Ralf Behr, L. Palafox +3 more

Recent metrological activities with programmable Josephson voltage standards (PJVS) are focused on extending the quantum accuracy to AC voltages, e.g. for the step-wise approximation of sine waves. Stimulated by the progress in this field, new requirements for the quality and availability of 1 V and 10 V circuits have been established. Based on the experience with programmable 1 V SINIS circuits fabricated at PTB and used at present by 13 National Metrological Institutes worldwide, the fabrication process and the microwave design were improved. The experience gained hereby enabled us to improve the properties of programmable 10 V SINIS arrays which were realized by us for the first time in 2000. The new 10 V circuits have 17 bit resolution and develop under 70 GHz microwave irradiation flat Shapiro steps at the 10 V level which are more than 600 muA wide. A direct comparison of the output voltage with a conventional 10 V SIS Josephson voltage standard confirmed the suitability for metrological applications. Incorporating 10 V-PJVS into existing AC metrology setups is expected to reduce their uncertainty budgets by about one order of magnitude.

IEEE Transactions on Applied Superconductivity•Jun 1, 2007•58 citations

Design of a turn-key 10 V Programmable Josephson Voltage Standard system

Paul D. Dresselhaus, Michael M. Elsbury, Charles J. Burroughs +5 more

NIST is designing a 10 V Programmable Josephson Voltage Standard (PJVS) system with an improved microwave design and arrays of stacked NbxSi1-x-barrier Josephson junctions. For this new design a "ground-up" approach was used that takes into account all system issues in order to produce a robust 10 V system. By improving the uniformity of the microwave drive along the length of each array, constant-voltage steps with a larger current range are generated allowing the use of smaller critical current junctions. Smaller critical currents are important for lowering the total overall power dissipated on chip. Reducing power dissipation also increases the operating margins. Thus, all aspects of the design are interrelated and important for an optimized system.

Conference on Precision Electromagnetic Measurements•Jun 1, 2008•4 citations
A 10 V programmable Josephson voltage standard (PJVS) circuit with a maximum output voltage of 20 V and a microwave bias of 18.5 GHz was designed and fabricated. Although an attempt was made to improve the fabrication yield for the 10 V PJVS circuit, it was not sufficiently large to reproducibly fabricate a perfect chip without any defects. The redundant arrays were additionally integrated to increase the maximum output voltage, which contributed to an increase in the number of available chips under the limited fabrication yield. Fortunately, most of the defective arrays had a zeroth Shapiro step, while the first step was very small or zero. If the array was not dc biased, it did not generate any voltage, because it worked as a superconductive wiring. In this case, the maximum output voltage became smaller than that of a perfect chip, but it functioned as a 10 V PJVS, due to the back-up arrays.
A 10-V programmable Josephson voltage standard (PJVS) circuit including 524 288 vertically stacked NbN/TiN/NbN Josephson junctions was successfully fabricated without any defects. The chip was cooled with a compact cryocooler at a temperature of 9.8 K and generated an output voltage of 17.3 V with the first Shapiro step height of 1.0 mA under microwave irradiation at 16 GHz. Furthermore, the circuit design having the high output voltage increased the number of available chips for the 10-V PJVS. The fabrication yield for the chip, which generates greater than 10 V, was 36%, which is ten times greater than that for a perfect chip without any defects. This method was not effective for the chip that had serious defects, such as a disconnection across the array or short between the array and ground; thus, efforts to reduce such defects, e.g., frequent maintenance inside vacuum chambers for film preparation and etching, were found to be essential.
Programmable Josephson voltage standard (PJVS) circuits using arrays of NbN/TiN/NbN/TiN/NbN double-junction stacks were fabricated and operated at a temperature of 10 K. Four arrays each with 32 768 junctions produced expected voltage outputs when driven at (10, 15, 17, and 20) GHz with an operating current range of 0.2-1.0 mA. Another circuit showed constant-voltage steps at /spl plusmn/6 V when driven with an 11 GHz microwave bias, indicating that over 260 000 junctions were operating properly. This circuit did not show constant-voltage steps when driven with a 19 GHz microwave bias, which was the design frequency to achieve /spl plusmn/10 V output voltage.
Programmable Josephson voltage standard (PJVS) circuits were developed that operate at 16 GHz to 20 GHz with operating margins larger than 1 mA. Two circuit designs were demonstrated, each having a total of ~ 300,000 junctions, which were divided into either 16 or 32 sub-arrays. Triple-stacked junctions were used in order to fit the ~300,000 junctions on each circuit. The amorphous NbxSi1-x-barrier junction technology provided a high degree of uniformity of the barrier and junction electrical properties, which was necessary to achieve the 1 mA operating margin. Although the margins on both the 16-array and 32-array circuits were much greater than 1 mA, the circuit yield for the 16-array design was lower because the longer arrays are more sensitive to defects. The use of lumped-element microwave splitters and tapered arrays significantly reduced the microwave input power and increased the operating margins of these designs. In addition, the broadband microwave response of the designs allowed the PJVS output voltage to be continuously adjusted by using the microwave frequency while remaining on margins.
524,288 NbN-based Josephson junctions were integrated to produce a programmable Josephson voltage standard (PJVS) on a die of 15mm × 15mm, and the PJVS circuit was cooled to 10K using a cryocooler and operated with a current margin of about 1.0mA. Although an output voltage of 10V was required for a voltage standard, the circuit was designed to generate the maximum output voltage of 17V because it was difficult to avoid a reduction of the output voltage due to defects. Although a perfect chip without any defect was rarely fabricated, the high voltage chip that generated at least 10V was fabricated with the fabrication yield of larger than 30%. The fabrication yield was also improved by optimizing the film growth conditions to reduce the film stress and the number of particles. Applications for a secondary voltage standard and an ac Josephson voltage standard are also described.
Recent metrological activities with programmable Josephson voltage standards (PJVS) are focused on extending the quantum accuracy to AC voltages, e.g. for the step-wise approximation of sine waves. Stimulated by the progress in this field, new requirements for the quality and availability of 1 V and 10 V circuits have been established. Based on the experience with programmable 1 V SINIS circuits fabricated at PTB and used at present by 13 National Metrological Institutes worldwide, the fabrication process and the microwave design were improved. The experience gained hereby enabled us to improve the properties of programmable 10 V SINIS arrays which were realized by us for the first time in 2000. The new 10 V circuits have 17 bit resolution and develop under 70 GHz microwave irradiation flat Shapiro steps at the 10 V level which are more than 600 muA wide. A direct comparison of the output voltage with a conventional 10 V SIS Josephson voltage standard confirmed the suitability for metrological applications. Incorporating 10 V-PJVS into existing AC metrology setups is expected to reduce their uncertainty budgets by about one order of magnitude.
NIST is designing a 10 V Programmable Josephson Voltage Standard (PJVS) system with an improved microwave design and arrays of stacked NbxSi1-x-barrier Josephson junctions. For this new design a "ground-up" approach was used that takes into account all system issues in order to produce a robust 10 V system. By improving the uniformity of the microwave drive along the length of each array, constant-voltage steps with a larger current range are generated allowing the use of smaller critical current junctions. Smaller critical currents are important for lowering the total overall power dissipated on chip. Reducing power dissipation also increases the operating margins. Thus, all aspects of the design are interrelated and important for an optimized system.