Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconductor Science and Technology

Design and operation of a rapid single flux quantum demultiplexer

Masaaki Maezawa, Motohiro Suzuki, Akira Shoji

Published Nov 21, 2002• 3 citations
Publisher

Abstract

A demultiplexer (DMUX) is a key subsystem of rapid single flux quantum (RSFQ) circuits and systems in practical applications. High-speed data from RSFQ circuits should be converted into sufficiently low-speed ones for transmission to and processing by room temperature electronics. We designed, fabricated and successfully tested an RSFQ DMUX based on the synchronous shift-and-dump architecture whose advantages are modularity and compactness. A 1-to-8 DMUX was implemented using our standard cell library on 1.6 kA cm −2 Nb trilayer technology. Fully functional operation was confirmed by low speed testing. Experimental bias margins were as large as ±16%. Results of average voltage measurements implied that the DMUX was operated at data rates up to 25 Gb s −1 .

DOI
10.1088/0953-2048/15/12/324

Related papers

Operation of a superconductive demultiplexer using rapid single flux quantum (RSFQ) technology

Steven B. Kaplan, Oleg A. Mukhanov

A superconductive demultiplexer was designed, simulated, and tested as an interface between ultra-fast superconductive circuits and slower room-temperature electronics. The modular RSFQ shift-and-dump circuit was designed as a register of Non-Destructive Read-Out (NDRO) cells, which are timed by pulses from the system clock. Data is read out from a 1:N demultiplexer every N clock periods by applying a read-out pulse to the register's NDRO input. Circuit simulations and results for the successful experimental test of a 2-stage demultiplexer will be discussed.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•25 citations

Simulation and 18 Gb/s testing of a data-driven self-timed RSFQ demultiplexer

Nobuyuki Yoshikawa, Z.J. Deng, Stephen R. Whiteley +1 more

We have developed a data-driven self-timed (DDST) rapid-single-flux-quantum (RSFQ) demultiplexer (demux) for the interface between on-chip high-speed RSFQ circuits and off-chip low-speed circuits. In order to eliminate the timing issue in a synchronous clocking system we employed the DDST architecture, where a clock signal is localized within a 2-bit basic demux module and dual rail lines are used to transfer the timing information between the modules. A larger demux can be produced simply by connecting the 2-bit modules in a tree structure. The DDST demux was designed for 10 Gb/s operation with sufficient dc bias margin using HYPRES 1 kA/cm/sup 2/ Nb process. We have successfully tested operation of the 2-bit demux up to 18 GHz using the DDST on-chip high-speed test system which was developed in our group.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•9 citations

4-bit rapid single-flux-quantum decoder

Alex F. Kirichenko, Vasili K. Semenov, Ying Ki Kwong +1 more

We describe the design of a fast single-flux-quantum decoder which can be used, e.g., in fast RAMs, general-purpose microprocessors, and communication channel switches. The core of the circuit is a tree of the single-bit SFQ demultiplexer with toggle (rather than the reset-set) control. Three new RSFQ cells: the demultiplexer, D flip-flop with complementary outputs, and serial XOR with large parameter tolerances (dc bias margins of /spl plusmn/25%, /spl plusmn/26%, and /spl plusmn/27%, respectively) have been developed for the decoder project. We have designed the first 16-bit prototype of the decoder for 1-kA/cm/sup 2/ niobium-trilayer technology and tested it at low frequencies. The circuit was completely operable except for 3 (of 16) output SFQ/DC converters. Simulations show that the circuit should allow data rate in excess of 60 Gbit/s and channel switching time below 20 ps.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•28 citations

Asynchronous circuits and systems in superconducting RSFQ digital technology

Z.J. Deng, Nobuyuki Yoshikawa, J. Tierno +2 more

Superconductive Rapid Single Flux Quantum (RSFQ) logic and memory, in which ones and zeros are represented by the presence or absence within a timing window of quantized picosecond voltage pulse (/spl int/v(t)dt=h/2e=2.07 mV/spl middot/ps), corresponding to one SFQ, can be integrated into a digital computing system with an operating rate of several tens of GHz, based on the present Nb Josephson junction integrated circuit technology. It is the most promising technology beyond semiconductor transistors for low-power high-end computation. However, as the operating speed of circuits and systems increase, timing uncertainty from fabrication process variations makes global synchronization very hard. In this paper, we present a globally asynchronous, locally synchronous timing methodology for RSFQ digital design, which can solve the global synchronization problem. We also demonstrate the recent experimental results of some asynchronous circuits and systems implemented in RSFQ technology. Several key components such as a self-timed shift register, a self-timed demultiplexor, a Muller-C element, a completion detector, and a clock generator have been designed and tested. High speed operation has been confirmed up to 20 Gb/s for a prototype data buffer system, which consists two self-timed shift registers and an on-chip 5-38 GHz clock generator.

IEEE International Symposium on Asynchronous Circuits and Systems (ASYNC)•Nov 27, 2002•7 citations

An asynchronous rapid single-flux-quantum demultiplexer based on dual-rail information coding

Boyko Dimov, M. Khabipov, D Balashov +4 more

We present a novel asynchronous RSFQ demultiplexer based on dual-rail information coding. The electrical scheme of the circuit is designed and optimized to maximize the margins of its elements and to improve the fabrication yield. This optimized scheme has been fabricated with the 4 µm 1 kA cm−2 Nb/Al2O3–Al/Nb technology of PTB-Braunschweig. The demultiplexer has been tested with different samples of the low-speed incoming data stream and in all cases a correct circuit functionality has been observed.

Superconductor Science and Technology•Apr 5, 2005•1 citation

Logic operation at 5 gb/s of an output interface for single-flux-quantum systems

N. Harada, Nobuyuki Yoshikawa, K. Yoda +2 more

High-speed logic operation of an output interface circuit for a single-flux-quantum (SFQ) system was demonstrated at a data rate of 5 Gb/s. Using NEC's 2.5-kA/cm/sup 2/ Nb junction process, we designed, fabricated, and tested the interface circuit consisting of a 2-b SFQ demultiplexer and two Josephson latching drivers. We verified the proper operation of the demultiplexer. The interface can convert 5-Gb/s SFQ-pulse data into two-channel 2.5-Gb/s return-to-zero data with an amplitude of approximately 6 mV.

IEEE Transactions on Applied Superconductivity•Sep 1, 2003•3 citations
A demultiplexer (DMUX) is a key subsystem of rapid single flux quantum (RSFQ) circuits and systems in practical applications. High-speed data from RSFQ circuits should be converted into sufficiently low-speed ones for transmission to and processing by room temperature electronics. We designed, fabricated and successfully tested an RSFQ DMUX based on the synchronous shift-and-dump architecture whose advantages are modularity and compactness. A 1-to-8 DMUX was implemented using our standard cell library on 1.6 kA cm −2 Nb trilayer technology. Fully functional operation was confirmed by low speed testing. Experimental bias margins were as large as ±16%. Results of average voltage measurements implied that the DMUX was operated at data rates up to 25 Gb s −1 .
A superconductive demultiplexer was designed, simulated, and tested as an interface between ultra-fast superconductive circuits and slower room-temperature electronics. The modular RSFQ shift-and-dump circuit was designed as a register of Non-Destructive Read-Out (NDRO) cells, which are timed by pulses from the system clock. Data is read out from a 1:N demultiplexer every N clock periods by applying a read-out pulse to the register's NDRO input. Circuit simulations and results for the successful experimental test of a 2-stage demultiplexer will be discussed.>
We have developed a data-driven self-timed (DDST) rapid-single-flux-quantum (RSFQ) demultiplexer (demux) for the interface between on-chip high-speed RSFQ circuits and off-chip low-speed circuits. In order to eliminate the timing issue in a synchronous clocking system we employed the DDST architecture, where a clock signal is localized within a 2-bit basic demux module and dual rail lines are used to transfer the timing information between the modules. A larger demux can be produced simply by connecting the 2-bit modules in a tree structure. The DDST demux was designed for 10 Gb/s operation with sufficient dc bias margin using HYPRES 1 kA/cm/sup 2/ Nb process. We have successfully tested operation of the 2-bit demux up to 18 GHz using the DDST on-chip high-speed test system which was developed in our group.
We describe the design of a fast single-flux-quantum decoder which can be used, e.g., in fast RAMs, general-purpose microprocessors, and communication channel switches. The core of the circuit is a tree of the single-bit SFQ demultiplexer with toggle (rather than the reset-set) control. Three new RSFQ cells: the demultiplexer, D flip-flop with complementary outputs, and serial XOR with large parameter tolerances (dc bias margins of /spl plusmn/25%, /spl plusmn/26%, and /spl plusmn/27%, respectively) have been developed for the decoder project. We have designed the first 16-bit prototype of the decoder for 1-kA/cm/sup 2/ niobium-trilayer technology and tested it at low frequencies. The circuit was completely operable except for 3 (of 16) output SFQ/DC converters. Simulations show that the circuit should allow data rate in excess of 60 Gbit/s and channel switching time below 20 ps.>
Superconductive Rapid Single Flux Quantum (RSFQ) logic and memory, in which ones and zeros are represented by the presence or absence within a timing window of quantized picosecond voltage pulse (/spl int/v(t)dt=h/2e=2.07 mV/spl middot/ps), corresponding to one SFQ, can be integrated into a digital computing system with an operating rate of several tens of GHz, based on the present Nb Josephson junction integrated circuit technology. It is the most promising technology beyond semiconductor transistors for low-power high-end computation. However, as the operating speed of circuits and systems increase, timing uncertainty from fabrication process variations makes global synchronization very hard. In this paper, we present a globally asynchronous, locally synchronous timing methodology for RSFQ digital design, which can solve the global synchronization problem. We also demonstrate the recent experimental results of some asynchronous circuits and systems implemented in RSFQ technology. Several key components such as a self-timed shift register, a self-timed demultiplexor, a Muller-C element, a completion detector, and a clock generator have been designed and tested. High speed operation has been confirmed up to 20 Gb/s for a prototype data buffer system, which consists two self-timed shift registers and an on-chip 5-38 GHz clock generator.
We present a novel asynchronous RSFQ demultiplexer based on dual-rail information coding. The electrical scheme of the circuit is designed and optimized to maximize the margins of its elements and to improve the fabrication yield. This optimized scheme has been fabricated with the 4 µm 1 kA cm−2 Nb/Al2O3–Al/Nb technology of PTB-Braunschweig. The demultiplexer has been tested with different samples of the low-speed incoming data stream and in all cases a correct circuit functionality has been observed.
High-speed logic operation of an output interface circuit for a single-flux-quantum (SFQ) system was demonstrated at a data rate of 5 Gb/s. Using NEC's 2.5-kA/cm/sup 2/ Nb junction process, we designed, fabricated, and tested the interface circuit consisting of a 2-b SFQ demultiplexer and two Josephson latching drivers. We verified the proper operation of the demultiplexer. The interface can convert 5-Gb/s SFQ-pulse data into two-channel 2.5-Gb/s return-to-zero data with an amplitude of approximately 6 mV.