Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE MTT-S International Microwave Symposium digest

Microwave stabilization of HEB mixer by a microchip controller

Alexander S. Shurakov, Edward Tong, R. Blundell, Gregory N Gol'tsman

Published Jun 1, 2012• 3 citations
Publisher

Abstract

The stability of a Hot Electron Bolometer (HEB) mixer can be improved by the use of microwave injection. In this article we report a refinement of this approach. We introduce a microchip controller to facilitate the implementation of the stabilization scheme, and demonstrate that the feedback loop effectively suppresses drifts in the HEB bias current, leading to an improvement in the receiver stability. The measured Allan time of the mixer's IF output power is increased to > 10 s.

DOI
10.1109/mwsym.2012.6259628

Related papers

Stabilization Scheme for Hot-Electron Bolometer Receivers Using Microwave Radiation

Рябчун Сергей Александрович, Edward Tong, R. Blundell +1 more

We present the results of a stabilization scheme for terahertz receivers based on NbN hot-electron bolometer (HEB) mixers that uses microwave radiation with a frequency much lower than the gap frequency of NbN to compensate for mixer current fluctuations. A feedback control loop, which actively controls the power level of the injected microwave radiation, has successfully been implemented to stabilize the operating point of the HEB mixer. This allows us to increase the receiver Allan time to 10 s and also improve the temperature resolution of the receiver by about 30% in the total power mode of operation.

IEEE Transactions on Applied Superconductivity•Dec 18, 2008•12 citations

Microwave Stabilization of a HEB Mixer in a Pulse-Tube Cryocooler

Alexander S. Shurakov, Edward Tong, R. Blundell +3 more

We report the results of our study of the stability of an 800 GHz hot electron bolometer (HEB) mixer cooled with a pulse-tube cryocooler. Pulse-tube cryocoolers introduce temperature fluctuations as well as mechanical vibrations at a frequency of$\sim$1 Hz, both of which can cause receiver gain fluctuations at that frequency. In our system, the motor of the cryocooler was separated from the cryostat to minimize mechanical vibrations, leaving thermal effects as the dominant source of the receiver gain fluctuations. We measured root mean square temperature variations of the 4 K stage of$\sim$7 mK. The HEB mixer was pumped by a solid state local oscillator at 810 GHz. The root mean square current fluctuations at the low noise operating point (1.50 mV, 56.5$\mu\hbox{A}$) were$\sim 0.12\ \mu\hbox{A}$, and were predominantly due to thermal fluctuations. To stabilize the bias current, microwave radiation was injected to the HEB mixer. The injected power level was set by a proportional-integral-derivative controller, which completely compensates for the bias current oscillations induced by the pulse-tube cryocooler. Significant improvement in the Allan variance of the receiver output power was obtained, and an Allan time of 5 s was measured.

IEEE Transactions on Applied Superconductivity•Jan 21, 2013•4 citations

Stabilisation of a Terahertz Hot-Electron Bolometer mixer with microwave feedback control

Рябчун Сергей Александрович, Edward Tong, R. Blundell +2 more

We report on implementation of microwave feedback control loop to stabilise the performance of an HEB mixer receiver. It is shown that the receiver sensitivity increases by a factor of 4 over a 16-minute scan, and the corresponding Allan time increases up to 10 seconds, as opposed to an open loop value of 1 second. Our experiments also demonstrate that the receiver sensitivity is limited by the intermediate frequency chain.

•Jan 1, 2007•3 citations

Probing the Stability of HEB Mixers With Microwave Injection

Andrey Trifonov, Edward Tong, R. Blundell +2 more

Using a microwave probe as a tool, we have performed experiments aimed at understanding the origin of the output-power fluctuations in hot-electron-bolometer (HEB) mixers. We use a probe frequency of 1.5 GHz. The microwave probe picks up impedance changes of the HEB, which are examined upon demodulation of the reflected wave outside the cryostat. This study shows that the HEB mixer operates in two different regimes under a terahertz pump. At a low pumping level, strong pulse modulation is observed, as the device switches between the superconducting state and the normal state at a rate of a few megahertz. When pumped much harder, to approximate the low-noise mixer operating point, residual modulation can still be observed, showing that the HEB mixer is intrinsically unstable even in the resistive state. Based on these observations, we introduced a low-frequency termination to the HEB mixer. By terminating the device in a 50-Ω resistor in the megahertz frequency range, we have been able to improve the output-power Allan time of our HEB receiver by a factor of four to about 10 s for a detection bandwidth of 15 MHz, with a corresponding gain fluctuation of about 0.035%.

IEEE Transactions on Applied Superconductivity•Nov 25, 2014•4 citations

The bias II feedback system: Understanding and improving stability in NbN HEB Terahertz receivers

Ric Zannoni, K. S. Yngvesson

Terahertz NbN heterodyne hot electron bolometer (HEB) mixer receivers currently provide the lowest receiver noise temperatures from about 1.2 THz to 5 THz. However, it has been well documented that these receivers are less stable, as quantified by the Allan variance, than other THz receivers (SIS and Schottky barrier diode mixers). In this paper we directly address the intermediate frequency (IF) stability of (HEB) receivers by designing and implementing a feedback system to stabilize the bias of the HEB device. We report a continuum Allan time of at least 20 seconds for a THz NbN HEB receiver.

International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz)•Sep 1, 2008•1 citation

Effect of microwave radiation on the stability of terahertz hot-electron bolometer mixers

Рябчун Сергей Александрович, Edward Tong, R. Blundell +2 more

We report our studies of the effect of microwave radiation, with a frequency much lower than that corresponding to the energy gap of the superconductor, on the performance of the NbN hot-electron bolometer (HEB) mixer incorporated into a THz heterodyne receiver. It is shown that exposing the HEB mixer to microwave radiation does not result in a significant rise of the receiver noise temperature and degradation of the mixer conversion gain so long as the level of microwave power is small compared to the local oscillator drive. Hence the injection of a small, but controlled amount of microwave radiation enables active compensation of local oscillator power and coupling fluctuations which can significantly degrade the stability of HEB mixer receivers.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Oct 18, 2006•2 citations
The stability of a Hot Electron Bolometer (HEB) mixer can be improved by the use of microwave injection. In this article we report a refinement of this approach. We introduce a microchip controller to facilitate the implementation of the stabilization scheme, and demonstrate that the feedback loop effectively suppresses drifts in the HEB bias current, leading to an improvement in the receiver stability. The measured Allan time of the mixer's IF output power is increased to > 10 s.
We present the results of a stabilization scheme for terahertz receivers based on NbN hot-electron bolometer (HEB) mixers that uses microwave radiation with a frequency much lower than the gap frequency of NbN to compensate for mixer current fluctuations. A feedback control loop, which actively controls the power level of the injected microwave radiation, has successfully been implemented to stabilize the operating point of the HEB mixer. This allows us to increase the receiver Allan time to 10 s and also improve the temperature resolution of the receiver by about 30% in the total power mode of operation.
We report the results of our study of the stability of an 800 GHz hot electron bolometer (HEB) mixer cooled with a pulse-tube cryocooler. Pulse-tube cryocoolers introduce temperature fluctuations as well as mechanical vibrations at a frequency of$\sim1Hz,bothofwhichcancausereceivergainfluctuationsatthatfrequency.Inoursystem,themotorofthecryocoolerwasseparatedfromthecryostattominimizemechanicalvibrations,leavingthermaleffectsasthedominantsourceofthereceivergainfluctuations.Wemeasuredrootmeansquaretemperaturevariationsofthe4Kstageof1 Hz, both of which can cause receiver gain fluctuations at that frequency. In our system, the motor of the cryocooler was separated from the cryostat to minimize mechanical vibrations, leaving thermal effects as the dominant source of the receiver gain fluctuations. We measured root mean square temperature variations of the 4 K stage of1Hz,bothofwhichcancausereceivergainfluctuationsatthatfrequency.Inoursystem,themotorofthecryocoolerwasseparatedfromthecryostattominimizemechanicalvibrations,leavingthermaleffectsasthedominantsourceofthereceivergainfluctuations.Wemeasuredrootmeansquaretemperaturevariationsofthe4Kstageof\sim7mK.TheHEBmixerwaspumpedbyasolidstatelocaloscillatorat810GHz.Therootmeansquarecurrentfluctuationsatthelownoiseoperatingpoint(1.50mV,56.57 mK. The HEB mixer was pumped by a solid state local oscillator at 810 GHz. The root mean square current fluctuations at the low noise operating point (1.50 mV, 56.57mK.TheHEBmixerwaspumpedbyasolidstatelocaloscillatorat810GHz.Therootmeansquarecurrentfluctuationsatthelownoiseoperatingpoint(1.50mV,56.5\mu\hbox{A})were) were)were\sim 0.12\ \mu\hbox{A}$, and were predominantly due to thermal fluctuations. To stabilize the bias current, microwave radiation was injected to the HEB mixer. The injected power level was set by a proportional-integral-derivative controller, which completely compensates for the bias current oscillations induced by the pulse-tube cryocooler. Significant improvement in the Allan variance of the receiver output power was obtained, and an Allan time of 5 s was measured.
Using a microwave probe as a tool, we have performed experiments aimed at understanding the origin of the output-power fluctuations in hot-electron-bolometer (HEB) mixers. We use a probe frequency of 1.5 GHz. The microwave probe picks up impedance changes of the HEB, which are examined upon demodulation of the reflected wave outside the cryostat. This study shows that the HEB mixer operates in two different regimes under a terahertz pump. At a low pumping level, strong pulse modulation is observed, as the device switches between the superconducting state and the normal state at a rate of a few megahertz. When pumped much harder, to approximate the low-noise mixer operating point, residual modulation can still be observed, showing that the HEB mixer is intrinsically unstable even in the resistive state. Based on these observations, we introduced a low-frequency termination to the HEB mixer. By terminating the device in a 50-Ω resistor in the megahertz frequency range, we have been able to improve the output-power Allan time of our HEB receiver by a factor of four to about 10 s for a detection bandwidth of 15 MHz, with a corresponding gain fluctuation of about 0.035%.
Terahertz NbN heterodyne hot electron bolometer (HEB) mixer receivers currently provide the lowest receiver noise temperatures from about 1.2 THz to 5 THz. However, it has been well documented that these receivers are less stable, as quantified by the Allan variance, than other THz receivers (SIS and Schottky barrier diode mixers). In this paper we directly address the intermediate frequency (IF) stability of (HEB) receivers by designing and implementing a feedback system to stabilize the bias of the HEB device. We report a continuum Allan time of at least 20 seconds for a THz NbN HEB receiver.
We report our studies of the effect of microwave radiation, with a frequency much lower than that corresponding to the energy gap of the superconductor, on the performance of the NbN hot-electron bolometer (HEB) mixer incorporated into a THz heterodyne receiver. It is shown that exposing the HEB mixer to microwave radiation does not result in a significant rise of the receiver noise temperature and degradation of the mixer conversion gain so long as the level of microwave power is small compared to the local oscillator drive. Hence the injection of a small, but controlled amount of microwave radiation enables active compensation of local oscillator power and coupling fluctuations which can significantly degrade the stability of HEB mixer receivers.