Superconducting radiation sensors are of particular interest for imaging applications in the sub-mm wavelength band because of their extraordinary sensitivity. The rising number of sensors integrated in one array entails the requirement of multiplexing techniques in order to reduce the number of wires leading into the cryogenic stage and thus reduce the thermal losses. One kind of promising code division multiplexing technique is based on a current steering switch (CSS), which is composed of two identical superconducting quantum interference devices (SQUIDs) in parallel current paths. One of them is switched from the superconducting into the normal state controlled by the applied magnetic flux. In this way the signal path can be altered and they can act as a polarity switch for analogue signals. We pursue this concept to use rapid single flux quantum (RSFQ) electronics for controlling these switches. As a first step, the SQUIDs of the CSS are inductively coupled to the storing loops of two delay flip flops (DFFs). Thus, one is able to toggle the polarity of the analogue switch by controlling the state of the DFF by RSFQ control signals. The results of simulations and measurements and also margin analyses are discussed.
Superconducting radiation sensors are of particular interest for imaging applications in the sub-mm wavelength band because of their extraordinary sensitivity. The rising number of sensors integrated in one array entails the requirement of multiplexing techniques in order to reduce the number of wires leading into the cryogenic stage and thus reduce the thermal losses. One kind of promising code division multiplexing technique is based on a current steering switch (CSS), which is composed of two identical superconducting quantum interference devices (SQUIDs) in parallel current paths. One of them is switched from the superconducting into the normal state controlled by the applied magnetic flux. In this way the signal path can be altered and they can act as a polarity switch for analogue signals. We pursue this concept to use rapid single flux quantum (RSFQ) electronics for controlling these switches. As a first step, the SQUIDs of the CSS are inductively coupled to the storing loops of two delay flip flops (DFFs). Thus, one is able to toggle the polarity of the analogue switch by controlling the state of the DFF by RSFQ control signals. The results of simulations and measurements and also margin analyses are discussed.
For spectroscopic and imaging applications in the submillimeter wavelength band, superconducting radiation sensors are widely used. Thereby, sensor arrays with a rising number of pixels require multiplexing techniques in order to reduce the number of wires leading to the cryogenic stage. A current steering switch (CSS) provides the basis for one kind of promising code division multiplexers. It is composed of two identical superconducting quantum interference devices (SQUIDs) in parallel current paths. Switching one of them from the superconducting into the normal state, which is controlled by the applied magnetic flux, alters the signal path; thus, they can act as a polarity switch for analog signals. In this paper, we describe a method that uses rapid single-flux quantum (RSFQ) electronics for controlling these switches. Therefore, their SQUIDs are inductively coupled each to the storing loop of an RSFQ delay flip-flop (DFF); hence, the state of the analog switch can be controlled by means of digital RSFQ signals. As a first step, we show the change in the critical current of the SQUIDs by the coupled operating digital circuit. For a wider operating range of the CSS, we developed a DFF, which is able to store a larger quantity of magnetic flux to make it possible to apply more flux to the coupled SQUID. For further improvements, we tested asymmetric SQUIDs to reduce the required magnetic flux. The results of the simulations and measurements are discussed.
Large arrays of superconducting radiation sensors require a multiplexed readout. One implementation of the promising code division multiplexing technique uses current steering switches (CSSs) based on superconducting quantum interference devices (SQUIDs). We pursue the concept of utilizing rapid single flux quantum (RSFQ) electronics to control these switches, where each SQUID of a CSS is inductively coupled to the storing loop of a delay flip-flop. The internal state of this digital logic element is represented by the presence of a magnetic flux quantum, which is destined to control the CSS.
We report on the development and test of an integrated system composed of a flux qubit and a rapid single-flux quantum (RSFQ) circuit that allows qubit manipulation. The goal is to demonstrate the feasibility of control electronics integrated on the same chip as the qubit, in view of the application in quantum computation with superconducting devices. RSFQ logic relies on the storage and transmission of magnetic flux quanta and can be profitably used with superconducting qubits because of the speed, scalability, compatibility with the qubit fabrication process and low temperature environment. While standard RSFQ circuitry is well assessed, the application to quantum computing requires a complete rescaling of parameter values, in order to preserve the qubit coherence and reduce the power dissipation. In the system presented in this paper, the qubit role is played by a superconducting loop interrupted by a small dc SQUID, usually called a double SQUID, which behaves as a tunable rf-SQUID. Its energy potential has the shape of a double well, with the barrier between the wells controlled by magnetic flux applied to the inner dc SQUID. Here for the first time we report measurements at a base temperature of 370 mK in which flux control pulses with desired characteristics were supplied by a RSFQ circuit fabricated using non-standard parameters in the same chip as the qubit.
Multiplexed superconducting quantum interference device (SQUID) amplifiers have recently enabled the deployment of kilopixel arrays of superconducting transition-edge sensor (TES) detectors on a variety of receivers for astrophysics. Existing multiplexing techniques for TES arrays, however, have constraints due to aliasing of SQUID noise, the size of the required filtering elements, or the complexity of the room-temperature electronics that make it difficult to scale to much larger arrays. We have developed a Walsh code-division SQUID multiplexer that has the potential to enable the multiplexing of larger arrays or pixels with faster thermal response times. The multiplexer uses superconducting switches to modulate the polarity of coupling between N individual TES detectors and a single output SQUID channel. The polarities of the detector signals are switched in the pattern of an N × N Walsh matrix, so a frame composed of N orthogonal samples can be used to reconstruct the detector signals without degradation. We present an analysis of the circuit architecture and preliminary results.
We report on a voltage-state logic family based on shunted Josephson junctions and on the Rapid Single Flux Quantum (RSFQ) concept. Storing information in a voltage-state form makes this Multi-Flux-Quantum Logic (MFQL) easier to match to complementary metal-oxide semiconductor (CMOS) circuits. The switching of MFQL element between the voltage and zero-voltage states takes a minimum of two SFQ pulses, and the switching time of this logic is comparable to that of RSFQ logic. The key logic element is an inverter in the form of an asymmetric interferometer, and the underlying idea is to use a separate superconducting wire to supply a standard dc output voltage for the elements. The asymmetric interferometer, directly coupled to the other elements, is actually a Josephson junction based three-terminal device or transistor. Elements such as NOT, OR, NOR, XOR, XNOR, a toggle flip-flop, and an RS trigger have been simulated, and show margins better than /spl plusmn/24%. The performance of this logic with current circuit fabrication technologies is also discussed.
Superconductive microwave rapid single-flux-quantum (RSFQ) digital circuits offer the possibility to digitally process signals in the frequency range of tens of GHz. An example of application to bring the advantages of this technology deals with digital SQUIDs, used for sensitive magnetometry with a broadband dynamics connected to a slew-rate in the GHz range. First recently obtained results of digital SQUID operation, based on Nb/Al-Al2O3/Nb shunted Josephson junctions, are presented in this article. In order to obtain the best performance of RSFQ circuits, and especially to push their speed at its limits, a precise diagnostic of such circuits is needed. We are developing a time-resolved diagnostic system based on sensitive photoconductive switches to sample the weak signals coming out of RSFQ circuits at cryogenic temperature. This system includes two different sorts of opto-RSFQ interfaces, based on superconducting and semiconducting materials, respectively. Some simulation results in the microwave range, along with measurements giving the potentialities of different photoswitches are presented.