Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Improved Operating Range of RSFQ-Controlled Current Steering Switches

Oliver Brandel, J. Kunert, Torsten May, Thomas Ortlepp, Hannes Toepfer, Hans‐Georg Meyer

Published Apr 17, 2014• 3 citations
Publisher

Abstract

For spectroscopic and imaging applications in the submillimeter wavelength band, superconducting radiation sensors are widely used. Thereby, sensor arrays with a rising number of pixels require multiplexing techniques in order to reduce the number of wires leading to the cryogenic stage. A current steering switch (CSS) provides the basis for one kind of promising code division multiplexers. It is composed of two identical superconducting quantum interference devices (SQUIDs) in parallel current paths. Switching one of them from the superconducting into the normal state, which is controlled by the applied magnetic flux, alters the signal path; thus, they can act as a polarity switch for analog signals. In this paper, we describe a method that uses rapid single-flux quantum (RSFQ) electronics for controlling these switches. Therefore, their SQUIDs are inductively coupled each to the storing loop of an RSFQ delay flip-flop (DFF); hence, the state of the analog switch can be controlled by means of digital RSFQ signals. As a first step, we show the change in the critical current of the SQUIDs by the coupled operating digital circuit. For a wider operating range of the CSS, we developed a DFF, which is able to store a larger quantity of magnetic flux to make it possible to apply more flux to the coupled SQUID. For further improvements, we tested asymmetric SQUIDs to reduce the required magnetic flux. The results of the simulations and measurements are discussed.

DOI
10.1109/tasc.2014.2318292

Related papers

RSFQ electronics for controlling superconducting polarity switches

Oliver Brandel, Olaf Wetzstein, T. May +3 more

Superconducting radiation sensors are of particular interest for imaging applications in the sub-mm wavelength band because of their extraordinary sensitivity. The rising number of sensors integrated in one array entails the requirement of multiplexing techniques in order to reduce the number of wires leading into the cryogenic stage and thus reduce the thermal losses. One kind of promising code division multiplexing technique is based on a current steering switch (CSS), which is composed of two identical superconducting quantum interference devices (SQUIDs) in parallel current paths. One of them is switched from the superconducting into the normal state controlled by the applied magnetic flux. In this way the signal path can be altered and they can act as a polarity switch for analogue signals. We pursue this concept to use rapid single flux quantum (RSFQ) electronics for controlling these switches. As a first step, the SQUIDs of the CSS are inductively coupled to the storing loops of two delay flip flops (DFFs). Thus, one is able to toggle the polarity of the analogue switch by controlling the state of the DFF by RSFQ control signals. The results of simulations and measurements and also margin analyses are discussed.

Superconductor Science and Technology•Oct 25, 2012•12 citations

Digital controlling of superconducting current steering switches

Oliver Brandel, J. Kunert, Torsten May +3 more

Large arrays of superconducting radiation sensors require a multiplexed readout. One implementation of the promising code division multiplexing technique uses current steering switches (CSSs) based on superconducting quantum interference devices (SQUIDs). We pursue the concept of utilizing rapid single flux quantum (RSFQ) electronics to control these switches, where each SQUID of a CSS is inductively coupled to the storing loop of a delay flip-flop. The internal state of this digital logic element is represented by the presence of a magnetic flux quantum, which is destined to control the CSS.

IEEE Workshop on Low Temperature Electronics (WOLTE)•Jul 1, 2014•0 citations

Code-division multiplexing of superconducting transition-edge sensor arrays

K. D. Irwin, Michael D. Niemack, Joern Beyer +7 more

Multiplexed superconducting quantum interference device (SQUID) amplifiers have recently enabled the deployment of kilopixel arrays of superconducting transition-edge sensor (TES) detectors on a variety of receivers for astrophysics. Existing multiplexing techniques for TES arrays, however, have constraints due to aliasing of SQUID noise, the size of the required filtering elements, or the complexity of the room-temperature electronics that make it difficult to scale to much larger arrays. We have developed a Walsh code-division SQUID multiplexer that has the potential to enable the multiplexing of larger arrays or pixels with faster thermal response times. The multiplexer uses superconducting switches to modulate the polarity of coupling between N individual TES detectors and a single output SQUID channel. The polarities of the detector signals are switched in the pattern of an N × N Walsh matrix, so a frame composed of N orthogonal samples can be used to reconstruct the detector signals without degradation. We present an analysis of the circuit architecture and preliminary results.

Superconductor Science and Technology•Feb 22, 2010•60 citations

Superconductive Microwave Single-Flux-Quantum Digital Circuits and Corresponding Opto-Electronic Interfaces: On-Going Studies and First Experimental Results

Pascal Febvre, Siham Badi, Torsten Reich +2 more

Superconductive microwave rapid single-flux-quantum (RSFQ) digital circuits offer the possibility to digitally process signals in the frequency range of tens of GHz. An example of application to bring the advantages of this technology deals with digital SQUIDs, used for sensitive magnetometry with a broadband dynamics connected to a slew-rate in the GHz range. First recently obtained results of digital SQUID operation, based on Nb/Al-Al2O3/Nb shunted Josephson junctions, are presented in this article. In order to obtain the best performance of RSFQ circuits, and especially to push their speed at its limits, a precise diagnostic of such circuits is needed. We are developing a time-resolved diagnostic system based on sensitive photoconductive switches to sample the weak signals coming out of RSFQ circuits at cryogenic temperature. This system includes two different sorts of opto-RSFQ interfaces, based on superconducting and semiconducting materials, respectively. Some simulation results in the microwave range, along with measurements giving the potentialities of different photoswitches are presented.

•Jul 13, 2005•0 citations

Rapid single-flux quantum control of the energy potential in a double SQUID qubit circuit

Maria Gabriella Castellano, F. Chiarello, Roberto Leoni +6 more

We report on the development and test of an integrated system composed of a flux qubit and a rapid single-flux quantum (RSFQ) circuit that allows qubit manipulation. The goal is to demonstrate the feasibility of control electronics integrated on the same chip as the qubit, in view of the application in quantum computation with superconducting devices. RSFQ logic relies on the storage and transmission of magnetic flux quanta and can be profitably used with superconducting qubits because of the speed, scalability, compatibility with the qubit fabrication process and low temperature environment. While standard RSFQ circuitry is well assessed, the application to quantum computing requires a complete rescaling of parameter values, in order to preserve the qubit coherence and reduce the power dissipation. In the system presented in this paper, the qubit role is played by a superconducting loop interrupted by a small dc SQUID, usually called a double SQUID, which behaves as a tunable rf-SQUID. Its energy potential has the shape of a double well, with the barrier between the wells controlled by magnetic flux applied to the inner dc SQUID. Here for the first time we report measurements at a base temperature of 370 mK in which flux control pulses with desired characteristics were supplied by a RSFQ circuit fabricated using non-standard parameters in the same chip as the qubit.

Superconductor Science and Technology•May 3, 2007•16 citations

RSFQ based microwave controller for qubit

Raihan Rafique, Thomas Ohki, Henrik Engseth +1 more

We present a Rapid Single Flux Quantum (RSFQ) microwave controller for superconducting qubits. Applying microwaves from room temperature sources is the conventional approach to excite quantum state transitions. Finding a method to apply short microwave bursts with a narrow linewidth is a challenge for on-chip Josephson based oscillators. We present a scheme containing an RSFQ pulse generator, ultra narrowband filter, SQUID based resonator and coupler. The operating frequency of the designed controller is 3-6 GHz. The unique feature of this design is a SQUID based resonator. By varying magnetic field in the SQUID, the\nresonance length can be varied between λ/4 and λ/2. The\nresonator is added as a shunt between the filter and coupler. Transmission of microwave signals from the filter to the output is determined by the shunt resonance. RSFQ T flip-flop circuit is designed to control the magnetic field applied to the SQUID in the resonator. Miniaturization of the coupler of 2-10 GHz has been done using a quasi-lumped element designed. We present the simulations results for the frequency response of\ndifferent resonance lengths of the modulator.

•Jan 1, 2007•1 citation
For spectroscopic and imaging applications in the submillimeter wavelength band, superconducting radiation sensors are widely used. Thereby, sensor arrays with a rising number of pixels require multiplexing techniques in order to reduce the number of wires leading to the cryogenic stage. A current steering switch (CSS) provides the basis for one kind of promising code division multiplexers. It is composed of two identical superconducting quantum interference devices (SQUIDs) in parallel current paths. Switching one of them from the superconducting into the normal state, which is controlled by the applied magnetic flux, alters the signal path; thus, they can act as a polarity switch for analog signals. In this paper, we describe a method that uses rapid single-flux quantum (RSFQ) electronics for controlling these switches. Therefore, their SQUIDs are inductively coupled each to the storing loop of an RSFQ delay flip-flop (DFF); hence, the state of the analog switch can be controlled by means of digital RSFQ signals. As a first step, we show the change in the critical current of the SQUIDs by the coupled operating digital circuit. For a wider operating range of the CSS, we developed a DFF, which is able to store a larger quantity of magnetic flux to make it possible to apply more flux to the coupled SQUID. For further improvements, we tested asymmetric SQUIDs to reduce the required magnetic flux. The results of the simulations and measurements are discussed.
Superconducting radiation sensors are of particular interest for imaging applications in the sub-mm wavelength band because of their extraordinary sensitivity. The rising number of sensors integrated in one array entails the requirement of multiplexing techniques in order to reduce the number of wires leading into the cryogenic stage and thus reduce the thermal losses. One kind of promising code division multiplexing technique is based on a current steering switch (CSS), which is composed of two identical superconducting quantum interference devices (SQUIDs) in parallel current paths. One of them is switched from the superconducting into the normal state controlled by the applied magnetic flux. In this way the signal path can be altered and they can act as a polarity switch for analogue signals. We pursue this concept to use rapid single flux quantum (RSFQ) electronics for controlling these switches. As a first step, the SQUIDs of the CSS are inductively coupled to the storing loops of two delay flip flops (DFFs). Thus, one is able to toggle the polarity of the analogue switch by controlling the state of the DFF by RSFQ control signals. The results of simulations and measurements and also margin analyses are discussed.
Large arrays of superconducting radiation sensors require a multiplexed readout. One implementation of the promising code division multiplexing technique uses current steering switches (CSSs) based on superconducting quantum interference devices (SQUIDs). We pursue the concept of utilizing rapid single flux quantum (RSFQ) electronics to control these switches, where each SQUID of a CSS is inductively coupled to the storing loop of a delay flip-flop. The internal state of this digital logic element is represented by the presence of a magnetic flux quantum, which is destined to control the CSS.
Multiplexed superconducting quantum interference device (SQUID) amplifiers have recently enabled the deployment of kilopixel arrays of superconducting transition-edge sensor (TES) detectors on a variety of receivers for astrophysics. Existing multiplexing techniques for TES arrays, however, have constraints due to aliasing of SQUID noise, the size of the required filtering elements, or the complexity of the room-temperature electronics that make it difficult to scale to much larger arrays. We have developed a Walsh code-division SQUID multiplexer that has the potential to enable the multiplexing of larger arrays or pixels with faster thermal response times. The multiplexer uses superconducting switches to modulate the polarity of coupling between N individual TES detectors and a single output SQUID channel. The polarities of the detector signals are switched in the pattern of an N × N Walsh matrix, so a frame composed of N orthogonal samples can be used to reconstruct the detector signals without degradation. We present an analysis of the circuit architecture and preliminary results.
Superconductive microwave rapid single-flux-quantum (RSFQ) digital circuits offer the possibility to digitally process signals in the frequency range of tens of GHz. An example of application to bring the advantages of this technology deals with digital SQUIDs, used for sensitive magnetometry with a broadband dynamics connected to a slew-rate in the GHz range. First recently obtained results of digital SQUID operation, based on Nb/Al-Al2O3/Nb shunted Josephson junctions, are presented in this article. In order to obtain the best performance of RSFQ circuits, and especially to push their speed at its limits, a precise diagnostic of such circuits is needed. We are developing a time-resolved diagnostic system based on sensitive photoconductive switches to sample the weak signals coming out of RSFQ circuits at cryogenic temperature. This system includes two different sorts of opto-RSFQ interfaces, based on superconducting and semiconducting materials, respectively. Some simulation results in the microwave range, along with measurements giving the potentialities of different photoswitches are presented.
We report on the development and test of an integrated system composed of a flux qubit and a rapid single-flux quantum (RSFQ) circuit that allows qubit manipulation. The goal is to demonstrate the feasibility of control electronics integrated on the same chip as the qubit, in view of the application in quantum computation with superconducting devices. RSFQ logic relies on the storage and transmission of magnetic flux quanta and can be profitably used with superconducting qubits because of the speed, scalability, compatibility with the qubit fabrication process and low temperature environment. While standard RSFQ circuitry is well assessed, the application to quantum computing requires a complete rescaling of parameter values, in order to preserve the qubit coherence and reduce the power dissipation. In the system presented in this paper, the qubit role is played by a superconducting loop interrupted by a small dc SQUID, usually called a double SQUID, which behaves as a tunable rf-SQUID. Its energy potential has the shape of a double well, with the barrier between the wells controlled by magnetic flux applied to the inner dc SQUID. Here for the first time we report measurements at a base temperature of 370 mK in which flux control pulses with desired characteristics were supplied by a RSFQ circuit fabricated using non-standard parameters in the same chip as the qubit.
We present a Rapid Single Flux Quantum (RSFQ) microwave controller for superconducting qubits. Applying microwaves from room temperature sources is the conventional approach to excite quantum state transitions. Finding a method to apply short microwave bursts with a narrow linewidth is a challenge for on-chip Josephson based oscillators. We present a scheme containing an RSFQ pulse generator, ultra narrowband filter, SQUID based resonator and coupler. The operating frequency of the designed controller is 3-6 GHz. The unique feature of this design is a SQUID based resonator. By varying magnetic field in the SQUID, the\nresonance length can be varied between λ/4 and λ/2. The\nresonator is added as a shunt between the filter and coupler. Transmission of microwave signals from the filter to the output is determined by the shunt resonance. RSFQ T flip-flop circuit is designed to control the magnetic field applied to the SQUID in the resonator. Miniaturization of the coupler of 2-10 GHz has been done using a quasi-lumped element designed. We present the simulations results for the frequency response of\ndifferent resonance lengths of the modulator.