Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Optics

Analysis of optical switching in a Yb3+-doped fiber Bragg grating by using self-phase modulation and cross-phase modulation

Zhigang Zang, Yujun Zhang

Published May 30, 2012• 169 citations
Publisher

Abstract

The optical performances of the all-optical switching based on Yb3+-doped fiber Bragg grating (FBG) are investigated under the case of self-phase modulation (SPM) and cross-phase modulation (XPM). For the SPM case, the optical bistability of FBG under different parameters is investigated. It shows that the width of the hysteresis loop and threshold switching power are strongly dependent on the fiber grating length, fiber grating detuning, and coupling constant. For the XPM case, the expressions of the threshold switching power in the different detuning range are given. The influence of parameters about different detuning and coupling constant to the threshold switching power and extinction ratio are also studied. In comparison with the SPM case, the switching power of FBG under XPM case can be reduced to less than 20 mW by optimizing the parameters of FBG.

DOI
10.1364/ao.51.003424

Related papers

Bistability threshold inside hysteresis loop of nonlinear fiber Bragg gratings

Yosia Yosia, Shum Ping, Chao Lü

We show the Cross Phase Modulation (XPM) effect between CW probe that operates in bistability region and strong Gaussian pump in a Fiber Bragg Grating (FBG) by Implicit 4th Order Runge-Kutta Method. The XPM effect results in three unique nonlinear switching behaviors of the probe transmission depending on the pump peak intensity and its Full Width Half Maximum (FWHM) value. From this observation, we offer the FBG three potential nonlinear switching applications in all-optical signal processing domain as: a step-up all-optical switching, an all-optical inverter, and an all-optical limiter. The bistability threshold that determines the nonlinear switching behaviors of probe transmission after Gaussian pump injection is defined numerically and shown to be equivalent to the unstable state inside hysteresis loop.

Optics Express•Jan 1, 2005•23 citations

Bistability and Switching in a Phase Shifted PT-Symmetric Fiber Bragg Grating

S. Hari Ramakrishnan, S. Vignesh Raja, A. Govindarajan +1 more

Using implicit Rungee-Kutta 4thorder method, we numerically report the optical bistablity and switching exhibited by a π-phase shifted nonlinear FBG with balanced gain and loss. Every control parameter which accounts for the variation in the hysteresis curve exhibited by the system is examined in detail. We begin with assessing the role of device length on the optical bistability and find that our system can exhibit switching at very short length of the fiber. Subsequently, the influence of coupling constant, detuning parameter and the nonlinearity on the switching power is also studied. The device exhibits switching at extremely low input intensities. Also, the effect of including the PT-symmetry on the switching characteristics of the device is investigated in brief.

International Conference on Vision Towards Emerging Trends in Communication and Networking (ViTECoN)•Mar 1, 2019•0 citations

Bistability of ultrashort pulses in FBG under different nonlinearity profiles

Paulo Victor Ferreira Pinto, T. M. Pessoa, J. M. Jacinto +3 more

In this work, we studied the optical bistability of Fiber Bragg Grating (FBG) under nonlinear regime, considering three increasing and decreasing profiles of nonlinearity: linear, quadratic and exponential. We varied the nonlinearity range in each profile, and obtained different curves of bistability and reflectivity. We analyzed the powers [Formula: see text] and [Formula: see text], as well as the width of the photonic band gap ([Formula: see text] of each device under different nonlinearity profiles, and we observed the changes in reflectivity of the FBG. The power intensities [Formula: see text] and [Formula: see text] obtained for the bistability of decreasing profiles were lower than those obtained for the increasing profiles, and the values of [Formula: see text] were also lower in decreasing profiles, which is useful for optical switching applications.

Journal of Nonlinear Optical Physics & Materials•Jun 1, 2017•3 citations

Low-switching power (<45 mW) optical bistability based on optical nonlinearity of ytterbium-doped fiber with a fiber Bragg grating pair

Zhigang Zang, Yujun Zhang

We propose a new optical bistable device (OBD), which is constructed by connecting two symmetrical fiber Bragg gratings with a ytterbium-doped fiber to form a nonlinear Fabry–Perot cavity. The principle of this new OBD is described using the transfer-matrix method, and the two groups of transmitted and reflected optical bistability loops under different parameters are investigated symmetrically. Compared with single fiber Bragg grating switching, whose switching power is greater than 2 kW, this new device has evident merits in reducing the switching power to less than 45 mW.

Journal of Modern Optics•Oct 14, 2011•127 citations

Graphene-controlled fiber Bragg grating and enabled optical bistability

Xuetao Gan, Yadong Wang, Fanlu Zhang +7 more

We report a graphene-assisted all-optical control of a fiber Bragg grating (FBG), which enables in-fiber optical bistability and switching. With an optical pump, a micro-FBG wrapped by graphene evolves into chirped and phase-shifted FBGs, whose characteristic wavelengths and bandwidths could be controlled by the pump power. Optical bistability and multistability are achieved in the controlled FBG based on a shifted Bragg reflection or Fabry-Perot-type resonance, which allow the implementation of optical switching with an extinction ratio exceeding 20 dB and a response time in tens of milliseconds.

Optics Letters•Jan 28, 2016•38 citations

Optimization of Optical Bistability in Chalcogenide Nonlinear Fiber Bragg Gratings

Elham Yousefi, Mohsen Hatami

In this paper, we study the bistability characteristics of chalcogenide nonlinear FBGs. The effect of length and third order nonlinearity on On-Off switching ratio and intensity distribution in FBG are investigated numerically. We obtained that there exist an optimum FBG length, that on-off switching ratio is maximized and is independent of the third order nonlinearity.

انجمن اپتیک و فوتونیک ایران•Feb 15, 2014•0 citations
The optical performances of the all-optical switching based on Yb3+-doped fiber Bragg grating (FBG) are investigated under the case of self-phase modulation (SPM) and cross-phase modulation (XPM). For the SPM case, the optical bistability of FBG under different parameters is investigated. It shows that the width of the hysteresis loop and threshold switching power are strongly dependent on the fiber grating length, fiber grating detuning, and coupling constant. For the XPM case, the expressions of the threshold switching power in the different detuning range are given. The influence of parameters about different detuning and coupling constant to the threshold switching power and extinction ratio are also studied. In comparison with the SPM case, the switching power of FBG under XPM case can be reduced to less than 20 mW by optimizing the parameters of FBG.
We show the Cross Phase Modulation (XPM) effect between CW probe that operates in bistability region and strong Gaussian pump in a Fiber Bragg Grating (FBG) by Implicit 4th Order Runge-Kutta Method. The XPM effect results in three unique nonlinear switching behaviors of the probe transmission depending on the pump peak intensity and its Full Width Half Maximum (FWHM) value. From this observation, we offer the FBG three potential nonlinear switching applications in all-optical signal processing domain as: a step-up all-optical switching, an all-optical inverter, and an all-optical limiter. The bistability threshold that determines the nonlinear switching behaviors of probe transmission after Gaussian pump injection is defined numerically and shown to be equivalent to the unstable state inside hysteresis loop.
Using implicit Rungee-Kutta 4thorder method, we numerically report the optical bistablity and switching exhibited by a π-phase shifted nonlinear FBG with balanced gain and loss. Every control parameter which accounts for the variation in the hysteresis curve exhibited by the system is examined in detail. We begin with assessing the role of device length on the optical bistability and find that our system can exhibit switching at very short length of the fiber. Subsequently, the influence of coupling constant, detuning parameter and the nonlinearity on the switching power is also studied. The device exhibits switching at extremely low input intensities. Also, the effect of including the PT-symmetry on the switching characteristics of the device is investigated in brief.
In this work, we studied the optical bistability of Fiber Bragg Grating (FBG) under nonlinear regime, considering three increasing and decreasing profiles of nonlinearity: linear, quadratic and exponential. We varied the nonlinearity range in each profile, and obtained different curves of bistability and reflectivity. We analyzed the powers [Formula: see text] and [Formula: see text], as well as the width of the photonic band gap ([Formula: see text] of each device under different nonlinearity profiles, and we observed the changes in reflectivity of the FBG. The power intensities [Formula: see text] and [Formula: see text] obtained for the bistability of decreasing profiles were lower than those obtained for the increasing profiles, and the values of [Formula: see text] were also lower in decreasing profiles, which is useful for optical switching applications.
We propose a new optical bistable device (OBD), which is constructed by connecting two symmetrical fiber Bragg gratings with a ytterbium-doped fiber to form a nonlinear Fabry–Perot cavity. The principle of this new OBD is described using the transfer-matrix method, and the two groups of transmitted and reflected optical bistability loops under different parameters are investigated symmetrically. Compared with single fiber Bragg grating switching, whose switching power is greater than 2 kW, this new device has evident merits in reducing the switching power to less than 45 mW.
We report a graphene-assisted all-optical control of a fiber Bragg grating (FBG), which enables in-fiber optical bistability and switching. With an optical pump, a micro-FBG wrapped by graphene evolves into chirped and phase-shifted FBGs, whose characteristic wavelengths and bandwidths could be controlled by the pump power. Optical bistability and multistability are achieved in the controlled FBG based on a shifted Bragg reflection or Fabry-Perot-type resonance, which allow the implementation of optical switching with an extinction ratio exceeding 20 dB and a response time in tens of milliseconds.