© 2026 Aqora Quantum S.A.S.

Terms Privacy Legal Notice

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE

Membrane-based quasi-optical superconducting HEB mixers at terahertz frequencies

G. Gay, R. Lefèvre, Y. Delorme, Frédéric Dauplay, A. Féret, T. Vacelet, L. Pelay, W. Miao, Michele . Batrung, Jean-Michel Krieg, L. Pagani

Published Sep 24, 2012• 0 citations

Abstract

Superconducting Hot Electron Bolometer mixers offer the highest sensitivity for heterodyne detections at frequencies above 1 THz. Important efforts have been made these recent years to further increase the HEB mixers' sensitivity and working frequency and also to design multi-pixel configuration. We present in this paper the developments of a non-standard quasi-optical membrane based HEB mixer where the commonly used focusing element, the silicon lens, is replaced by a micro-mirror and a membrane-based back-short. This configuration offers many advantages: easier processing for circuits at very high frequencies, better noise temperature brought by lower RF coupling loss and higher gain of the antenna. This design is also considered very attractive for multi-pixel receivers. The devices are made of phonon-cooled NbN HEB mixers processed on 1.4 μm thick stress-less Si3N4/Si02 membrane. Quasi-optical designs have been made for frequencies at 600 GHz and 2.5 THz. The design and the device fabrication process will be discussed and both DC and RF measurements at 600 GHz will be presented.

DOI: 10.1117/12.926892

Related papers

2.5 THz multipixel heterodyne receiver based on NbN HEB mixers

Serguei Cherednichenko, Vladimir Drakinskiy, Jean Baubert +8 more

A 16 pixel heterodyne receiver for 2.5 THz has been developed based on NbN superconducting hot-electron bolometer (HEB) mixers. The receiver uses a quasioptical RF coupling approach where HEB mixers are integrated into double dipole antennas on 1.5μm thick Si3N4/SiO2 membranes. Spherical mirrors (one per pixel) and backshort distance from the antenna have been used to design the output mixer beam profile. The camera design allows all 16 pixel IF readout in parallel. The gain bandwidth of the HEB mixers on Si3N4/SiO2 membranes was found to be 0.7÷0.9 GHz, which is much smaller than for similar devices on silicon. Application of buffer layers and use of alternative types of membranes (e.g. silicon-on-insulator) is under investigation.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jun 14, 2006•8 citations

Membrane-based HEB mixer for THz applications

Jean Baubert, Morvan C. Salez, Y. Delorme +4 more

We report in this paper a new concept for 2.7 THz superconducting Niobium nitride (NbN) Hot-Electron Bolometer mixer (HEB). The membrane process was developped for space telecommnunication applications a few years ago and the HEB mixer concept is now considered as the best choice for low-noise submillimeter-wave frequency heterodyne receivers. The idea is then to join these two technologies. The novel fabrication scheme is to fabricate a NbN HEB mixer on a 1 μm thick stress-less Si3N4/SiO2 membrane. This seems to present numerous improvements concerning : use at higher RF frequencies, power coupling efficiency, HEB mixer sensitivity, noise temperature, and space applications. This work is to be continued within the framework of an ESA TRP project, a 2.7 THz heterodyne camera with numerous applications including a SOFIA airborne receiver. This paper presents the whole fabrication process, the validation tests and preliminary results. Membrane-based HEB mixer theory is currently being investigated and further tests such as heterodyne and Fourier transform spectrometry measurement are planed shortly.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 25, 2003•2 citations

2.5 THz multipixel heterodyne receiver based on NbN HEB mixers

Serguei Cherednichenko, Vladimir Drakinskiy, Jean Baubert +8 more

A 16 pixel heterodyne receiver for 2.5 THz has been developed based on NbN superconducting hot-electron bolometer (HEB) mixers. The receiver uses a quasioptical RF coupling approach where HEB mixers are integrated into double dipole antennas on 1.5µm thick Si3N4/SiO2 membranes. Spherical mirrors (one per pixel) and backshort distance from the antenna have been used to design the output mixer beam profile. The camera design allows all 16 pixel IF readout in parallel. The gain bandwidth of the HEB mixers on Si3N4/SiO2 membranes was found to be 0.7÷0.9 GHz, which is much smaller than for similar devices on silicon. Application of buffer layers and use of alternative types of membrandes (e.g. silicon-on-insulator) is under investigation.

•May 31, 2006•11 citations

16 Pixel HEB Heterodyne Receiver for 2.5 THz

Serguei Cherednichenko, Vladimir Drakinskiy, Jean Baubert +8 more

A 16 pixel heterodyne receiver for 2.5 THz has been developed based on NbN superconducting hot-electron bolometer (HEB) mixers. The receiver uses a quasioptical RF coupling approach where HEB mixers are integrated into double dipole antennas on 1.5m thick Si3N4/ SiO2 membranes. Spherical mirrors (one per pixel) and backshort distance from the antenna have been used to design the output mixer beam profile. We present here the results of the antenna simulations using HFSS and ADS, as well as the beam calculations after the collimating mirror.

Softwaretechnik-Trends•May 1, 2006•0 citations

16 Pixel HEB Heterodyne Mixer Array for 2.5 THz

Vladimir Drakinskiy, Serguei Cherednichenko, Terese Berg +5 more

A 16 pixel heterodyne receiver for 2.5 THz has been developed based on NbN superconducting hot-electron bolometer (HEB) mixers. The receiver uses a quasioptical RF coupling approach where HEB mixers are integrated into double dipole antennas on 1.5 mum thick Si3N4/ SiO2 membranes. Spherical mirrors (one per pixel) and backshort distance from the antenna have been used to design the output mixer beam profile. We present here the results of the antenna simulations using HFSS and ADS, as well as the beam calculations after the collimating mirror.

•Oct 1, 2007•0 citations

NbN Hot Electron Bolometric Mixers for a Quasi--Optical THz Receiver

M. Kroug

Experimental work on the development of a quasi-optical heterodyne receiver for the THz frequency range is reported. The mixing device is a superconducting hot electron bolometer (HEB) made from ultrathin, d = 3 - 5 nm, niobium nitride (NbN) films. Work described in this thesis comprises: The design of a prototype receiver using quasi-optical coupling. Device fabrication involving reactive magnetron sputtering of NbN films and lithographic definition of the antenna integrated mixer. An investigation of the receiver performance at frequencies between 0.6 THz and 2.5 THz. The best performance is obtained with HEB mixers made from NbN films with a thickness d = 3-3.5 nm and a critical temperature T c = 9 - 9.5 K. Double-side band receiver noise temperatures are 530 K at 0.6 THz, 650 K at 1.6 THz and 1100 K at 2.5 THz. Corrected for losses in the receiver input optics, these values amount to only 10 times the theoretical quantum limit. MgO as the substrate material has been shown to provide improved acoustic coupling between NbN film and the substrate compared to other materials such as Si or sapphire. A maximum IF gain bandwidth of 4.5 GHz has been measured under the same operating conditions which yield lowest noise temperature. The local oscilltor power requirement is ~250 nW absorbed in the bolometer. Quasi-optically coupled HEB mixers have become the device-of-choice for radio astronomical applications in the frequency regime at and above 1 THz.

•Jan 1, 2001•4 citations

Superconducting Hot Electron Bolometer mixers offer the highest sensitivity for heterodyne detections at frequencies above 1 THz. Important efforts have been made these recent years to further increase the HEB mixers' sensitivity and working frequency and also to design multi-pixel configuration. We present in this paper the developments of a non-standard quasi-optical membrane based HEB mixer where the commonly used focusing element, the silicon lens, is replaced by a micro-mirror and a membrane-based back-short. This configuration offers many advantages: easier processing for circuits at very high frequencies, better noise temperature brought by lower RF coupling loss and higher gain of the antenna. This design is also considered very attractive for multi-pixel receivers. The devices are made of phonon-cooled NbN HEB mixers processed on 1.4 μm thick stress-less Si3N4/Si02 membrane. Quasi-optical designs have been made for frequencies at 600 GHz and 2.5 THz. The design and the device fabrication process will be discussed and both DC and RF measurements at 600 GHz will be presented.

A 16 pixel heterodyne receiver for 2.5 THz has been developed based on NbN superconducting hot-electron bolometer (HEB) mixers. The receiver uses a quasioptical RF coupling approach where HEB mixers are integrated into double dipole antennas on 1.5μm thick Si3N4/SiO2 membranes. Spherical mirrors (one per pixel) and backshort distance from the antenna have been used to design the output mixer beam profile. The camera design allows all 16 pixel IF readout in parallel. The gain bandwidth of the HEB mixers on Si3N4/SiO2 membranes was found to be 0.7÷0.9 GHz, which is much smaller than for similar devices on silicon. Application of buffer layers and use of alternative types of membranes (e.g. silicon-on-insulator) is under investigation.

We report in this paper a new concept for 2.7 THz superconducting Niobium nitride (NbN) Hot-Electron Bolometer mixer (HEB). The membrane process was developped for space telecommnunication applications a few years ago and the HEB mixer concept is now considered as the best choice for low-noise submillimeter-wave frequency heterodyne receivers. The idea is then to join these two technologies. The novel fabrication scheme is to fabricate a NbN HEB mixer on a 1 μm thick stress-less Si3N4/SiO2 membrane. This seems to present numerous improvements concerning : use at higher RF frequencies, power coupling efficiency, HEB mixer sensitivity, noise temperature, and space applications. This work is to be continued within the framework of an ESA TRP project, a 2.7 THz heterodyne camera with numerous applications including a SOFIA airborne receiver. This paper presents the whole fabrication process, the validation tests and preliminary results. Membrane-based HEB mixer theory is currently being investigated and further tests such as heterodyne and Fourier transform spectrometry measurement are planed shortly.

A 16 pixel heterodyne receiver for 2.5 THz has been developed based on NbN superconducting hot-electron bolometer (HEB) mixers. The receiver uses a quasioptical RF coupling approach where HEB mixers are integrated into double dipole antennas on 1.5µm thick Si3N4/SiO2 membranes. Spherical mirrors (one per pixel) and backshort distance from the antenna have been used to design the output mixer beam profile. The camera design allows all 16 pixel IF readout in parallel. The gain bandwidth of the HEB mixers on Si3N4/SiO2 membranes was found to be 0.7÷0.9 GHz, which is much smaller than for similar devices on silicon. Application of buffer layers and use of alternative types of membrandes (e.g. silicon-on-insulator) is under investigation.

A 16 pixel heterodyne receiver for 2.5 THz has been developed based on NbN superconducting hot-electron bolometer (HEB) mixers. The receiver uses a quasioptical RF coupling approach where HEB mixers are integrated into double dipole antennas on 1.5m thick Si3N4/ SiO2 membranes. Spherical mirrors (one per pixel) and backshort distance from the antenna have been used to design the output mixer beam profile. We present here the results of the antenna simulations using HFSS and ADS, as well as the beam calculations after the collimating mirror.

A 16 pixel heterodyne receiver for 2.5 THz has been developed based on NbN superconducting hot-electron bolometer (HEB) mixers. The receiver uses a quasioptical RF coupling approach where HEB mixers are integrated into double dipole antennas on 1.5 mum thick Si3N4/ SiO2 membranes. Spherical mirrors (one per pixel) and backshort distance from the antenna have been used to design the output mixer beam profile. We present here the results of the antenna simulations using HFSS and ADS, as well as the beam calculations after the collimating mirror.

Experimental work on the development of a quasi-optical heterodyne receiver for the THz frequency range is reported. The mixing device is a superconducting hot electron bolometer (HEB) made from ultrathin, d = 3 - 5 nm, niobium nitride (NbN) films. Work described in this thesis comprises: The design of a prototype receiver using quasi-optical coupling. Device fabrication involving reactive magnetron sputtering of NbN films and lithographic definition of the antenna integrated mixer. An investigation of the receiver performance at frequencies between 0.6 THz and 2.5 THz. The best performance is obtained with HEB mixers made from NbN films with a thickness d = 3-3.5 nm and a critical temperature T c = 9 - 9.5 K. Double-side band receiver noise temperatures are 530 K at 0.6 THz, 650 K at 1.6 THz and 1100 K at 2.5 THz. Corrected for losses in the receiver input optics, these values amount to only 10 times the theoretical quantum limit. MgO as the substrate material has been shown to provide improved acoustic coupling between NbN film and the substrate compared to other materials such as Si or sapphire. A maximum IF gain bandwidth of 4.5 GHz has been measured under the same operating conditions which yield lowest noise temperature. The local oscilltor power requirement is ~250 nW absorbed in the bolometer. Quasi-optically coupled HEB mixers have become the device-of-choice for radio astronomical applications in the frequency regime at and above 1 THz.