© 2026 Aqora Quantum S.A.S.

Terms Privacy Legal Notice

IEICE Transactions on Electronics

Superconductor Digital-RF Receiver Systems

Oleg A. Mukhanov, Dmitri E. Kirichenko, I. V. Vernik, Timur V. Filippov, Alex F. Kirichenko, R. WEBBER, Vladimir Valentinovich Dotsenko, Andrei Talalaevskii, Jia Tang, Anubhav Sahu, Pavel Shevchenko, Ronald Earle Miller, Steven B. Kaplan, Saad M. Sarwana, D. GUPTA

Published Mar 1, 2008• 130 citations

Abstract

Digital superconductor electronics has been experiencing rapid maturation with the emergence of smaller-scale, lower-cost communications applications which became the major technology drivers. These applications are primarily in the area of wireless communications, radar, and surveillance as well as in imaging and sensor systems. In these areas, the fundamental advantages of superconductivity translate into system benefits through novel Digital-RF architectures with direct digitization of wide band, high frequency radio frequency (RF) signals. At the same time the availability of relatively small 4K cryocoolers has lowered the foremost market barrier for cryogenically-cooled digital electronic systems. Recently, we have achieved a major breakthrough in the development, demonstration, and successful delivery of the cryocooled superconductor digital-RF receivers directly digitizing signals in a broad range from kilohertz to gigahertz. These essentially hybrid-technology systems combine a variety of superconductor and semiconductor technologies packaged with two-stage commercial cryocoolers: cryogenic Nb mixed-signal and digital circuits based on Rapid Single Flux Quantum (RSFQ) technology, room-temperature amplifiers, FPGA processing and control circuitry. The demonstrated cryocooled digital-RF systems are the world's first and fastest directly digitizing receivers operating with live satellite signals in X-band and performing signal acquisition in HF to L-band at ∼30GHz clock frequencies.

DOI: 10.1093/ietele/e91-c.3.306

Related papers

High Performance HF-VHF All Digital RF Receiver Tested at 20 GHz Clock Frequencies

Anna De Escobar, Richard Hitt, Oleg A. Mukhanov +1 more

Wireless applications would be less expensive, more flexible, and more robust if they had more digital and less analog circuitry. The problem is implementing digital signal processing at radio frequencies. Conventional data converters (ADCs and DACs) and digital circuits are simply not fast enough. However, superconductors can provide ultra fast mixed signal and digital circuits with the linearity and dynamic range required for true direct, digital-RF processing. These superconducting circuits are digital ICs based on Josephson junctions and "rapid-single-flux-quantum" logic (RSFQ), where switching speeds up to 750 GHz have been demonstrated enabling true digital-RF architecture at clock speeds eventually up to 160 GHz. This permits direct conversion between analog RF and digital baseband signals, replacing frequency and protocol-specific analog hardware with flexible digital processors. Data conversion in high frequency wireless applications at frequencies up to 50 GHz will soon become practical. Hypres recently delivered a HF-VHF all digital RF receiver (ADR) prototype to ONR. Testing of this ADR has demonstrated the superior performance of superconducting ICs in cryocooled systems. A US Navy laboratory is now evaluating the world's first complete prototype digital RF receiver capable of direct digitization from DC to 2 GHz

IEEE Military Communications Conference (MILCOM)•Oct 1, 2006•7 citations

OPERATION OF SUPERCONDUCTING DIGITAL RECEIVER CIRCUITS ON 2-STAGE GIFFORD-MCMAHON CRYOCOOLER

Robert J. Webber, Vladimir Valentinovich Dotsenko, Andrei Talalaevskii +23 more

We have demonstrated the full operation of digital RF receivers on a HYPRES-designed cryostat, which couples an Nb-based superconducting Rapid Single Flux Quantum (RSFQ) chip to a commercially available 100 mW 4 Kelvin Gifford-McMahon cryocooler. A field demonstration of digitization of a satellite-received signal at 7.7 GHz is described. The digital receiver chip is a 1 cm×1 cm chip comprising ∼11,000 Josephson junctions (JJ). The measured cryogenic thermal and magnetic environments of the chip are discussed and their impact on performance. Reception and direct digital conversion of real signals in the HF-, VHF-, and X-bands including signals from military satellite antennae shows the potential of this system to replace large and power-hungry multiple analog receivers.

AIP conference proceedings•Jan 1, 2008•10 citations

Superconductor analog-to-digital converters and their applications

Deepnarayan Gupta, Amol Inamdar, Dmitri E. Kirichenko +2 more

A wide variety of applications, ranging from radio-frequency (RF) receivers for broadband communications and signal detection, on earth and in space, would benefit from high-performance superconductor analog-to-digital converters (ADCs), based on magnetic flux quantization and fast switching Josephson junctions. Superconductor ADCs are capable of very high sample rates (100 GHz or more), very high linearity, and high sensitivity. Nyquist-rate ADCs use the high sample rate to digitize a wide instantaneous bandwidth (tens of GHz) and are useful for wideband spectrum monitoring as well as high-end scientific instrumentation. Delta and delta-sigma oversampling ADCs use the high linearity to achieve programmable trade-off between dynamic range and instantaneous bandwidth. These lowpass and bandpass ADCs have been used for direct digitization of narrower (tens to hundreds of MHz) RF bands in the 1-20 GHz range for a variety of communications, intelligence, electronic warfare, and radar applications. Another application area of these cryogenic ADCs is for outputs of cryogenic sensor arrays and terahertz mixers. Recent advances in various classes of ADCs for different applications are described.

IEEE MTT-S International Microwave Symposium digest•Jun 1, 2011•21 citations

Superconductor Digital-RF Transceiver Components

Oleg A. Mukhanov, Deepnarayan Gupta, Alan M. Kadin +3 more

Superconductive technology offers unparalleled digital and mixed-signal circuit performance, advancing digital processing from baseband to RF stages. This allows elimination of analog filters and mixers with generally poorly controlled phase performance, causing intersymbol interference limiting an overall communication system performance. HYPRES has been developing superconducting circuit components for application to digital RF communication transceivers. The components include low-pass and band-pass analog-to-digital converters, digital decimation and correlation-based filters, digital up/down-converters, and low-time-jitter clock sources. All of these are based on ultra-fast Rapid Single Flux Quantum (RSFQ) digital circuits, with clock rates up to 20 GHz demonstrated with 3-micron technology, and being scaled to 40 GHz and above. In this paper, we will discuss design and performance of some of these components. 1.

•Jan 1, 2006•7 citations

Superconductor digital RF development for software radio

DARREN K. BROCK, Oleg A. Mukhanov, José M. de la Rosa

We review a new "direct digitization" approach for "digital RF" architectures for software radio. Although direct digitization usually implies the simultaneous digitization of all channels in a particular band at a downconverted IF, we use this term to refer exclusively to the direct digitization of all bands, from near DC to RF. Furthermore, we present results on band selection and digitization of RF signals directly at the carrier frequency with high resolution. These novel approaches are enabled by a superconductor analog-to-digital converter technology using an ultra-fast IC logic known as Rapid Single Flux Quantum (RSFQ) logic, with performance capable of enabling envisioned software radios.

IEEE Communications Magazine•Jan 1, 2001•45 citations

High Performance, All Digital RF Receiver Tested at 7.5 GigaHertz

Jack Wong, Rick Dunnegan, Deepnarayan Gupta +6 more

Wireless applications would be less expensive, more flexible, and more robust if they had more digital and less analog circuitry. The problem is implementing digital signal processing at radio frequencies. Conventional data converters (ADCs and DACs) and digital circuits are simply not fast enough, especially at SATCOM frequencies. However, superconductors can provide ultra fast mixed signal and digital circuits with the linearity and dynamic range required for true direct, digital-RF processing. These superconducting circuits are digital ICs based on Josephson junctions and "rapid-single-flux-quantum" logic (RSFQ), where simple circuit switching speeds up to 750 GHz have been demonstrated. This permits direct conversion between analog RF and digital baseband signals, replacing frequency and protocol-specific analog hardware with flexible digital processors. HYPRES recently developed and delivered an X-band All Digital RF Receiver (XADR) prototype system for the US Army CERDEC and PM DCATS. The concept of this ADR is to replace the entire analog RF receive chain between the antenna and the baseband demodulator with a high performance digital RF equivalent. The first XADR prototype system has been successfully demonstrated at the Joint SATCOM engineering Center (JSEC). End to end link testing, over the satellite has been successfully completed using an existing AN/GSC-39 X-band earth terminal, an XTAR satellite, the X-band ADR and a SATCOM modem.

IEEE Military Communications Conference (MILCOM)•Oct 1, 2007•15 citations

Digital superconductor electronics has been experiencing rapid maturation with the emergence of smaller-scale, lower-cost communications applications which became the major technology drivers. These applications are primarily in the area of wireless communications, radar, and surveillance as well as in imaging and sensor systems. In these areas, the fundamental advantages of superconductivity translate into system benefits through novel Digital-RF architectures with direct digitization of wide band, high frequency radio frequency (RF) signals. At the same time the availability of relatively small 4K cryocoolers has lowered the foremost market barrier for cryogenically-cooled digital electronic systems. Recently, we have achieved a major breakthrough in the development, demonstration, and successful delivery of the cryocooled superconductor digital-RF receivers directly digitizing signals in a broad range from kilohertz to gigahertz. These essentially hybrid-technology systems combine a variety of superconductor and semiconductor technologies packaged with two-stage commercial cryocoolers: cryogenic Nb mixed-signal and digital circuits based on Rapid Single Flux Quantum (RSFQ) technology, room-temperature amplifiers, FPGA processing and control circuitry. The demonstrated cryocooled digital-RF systems are the world's first and fastest directly digitizing receivers operating with live satellite signals in X-band and performing signal acquisition in HF to L-band at ∼30GHz clock frequencies.

Wireless applications would be less expensive, more flexible, and more robust if they had more digital and less analog circuitry. The problem is implementing digital signal processing at radio frequencies. Conventional data converters (ADCs and DACs) and digital circuits are simply not fast enough. However, superconductors can provide ultra fast mixed signal and digital circuits with the linearity and dynamic range required for true direct, digital-RF processing. These superconducting circuits are digital ICs based on Josephson junctions and "rapid-single-flux-quantum" logic (RSFQ), where switching speeds up to 750 GHz have been demonstrated enabling true digital-RF architecture at clock speeds eventually up to 160 GHz. This permits direct conversion between analog RF and digital baseband signals, replacing frequency and protocol-specific analog hardware with flexible digital processors. Data conversion in high frequency wireless applications at frequencies up to 50 GHz will soon become practical. Hypres recently delivered a HF-VHF all digital RF receiver (ADR) prototype to ONR. Testing of this ADR has demonstrated the superior performance of superconducting ICs in cryocooled systems. A US Navy laboratory is now evaluating the world's first complete prototype digital RF receiver capable of direct digitization from DC to 2 GHz

We have demonstrated the full operation of digital RF receivers on a HYPRES-designed cryostat, which couples an Nb-based superconducting Rapid Single Flux Quantum (RSFQ) chip to a commercially available 100 mW 4 Kelvin Gifford-McMahon cryocooler. A field demonstration of digitization of a satellite-received signal at 7.7 GHz is described. The digital receiver chip is a 1 cm×1 cm chip comprising ∼11,000 Josephson junctions (JJ). The measured cryogenic thermal and magnetic environments of the chip are discussed and their impact on performance. Reception and direct digital conversion of real signals in the HF-, VHF-, and X-bands including signals from military satellite antennae shows the potential of this system to replace large and power-hungry multiple analog receivers.

A wide variety of applications, ranging from radio-frequency (RF) receivers for broadband communications and signal detection, on earth and in space, would benefit from high-performance superconductor analog-to-digital converters (ADCs), based on magnetic flux quantization and fast switching Josephson junctions. Superconductor ADCs are capable of very high sample rates (100 GHz or more), very high linearity, and high sensitivity. Nyquist-rate ADCs use the high sample rate to digitize a wide instantaneous bandwidth (tens of GHz) and are useful for wideband spectrum monitoring as well as high-end scientific instrumentation. Delta and delta-sigma oversampling ADCs use the high linearity to achieve programmable trade-off between dynamic range and instantaneous bandwidth. These lowpass and bandpass ADCs have been used for direct digitization of narrower (tens to hundreds of MHz) RF bands in the 1-20 GHz range for a variety of communications, intelligence, electronic warfare, and radar applications. Another application area of these cryogenic ADCs is for outputs of cryogenic sensor arrays and terahertz mixers. Recent advances in various classes of ADCs for different applications are described.

Superconductive technology offers unparalleled digital and mixed-signal circuit performance, advancing digital processing from baseband to RF stages. This allows elimination of analog filters and mixers with generally poorly controlled phase performance, causing intersymbol interference limiting an overall communication system performance. HYPRES has been developing superconducting circuit components for application to digital RF communication transceivers. The components include low-pass and band-pass analog-to-digital converters, digital decimation and correlation-based filters, digital up/down-converters, and low-time-jitter clock sources. All of these are based on ultra-fast Rapid Single Flux Quantum (RSFQ) digital circuits, with clock rates up to 20 GHz demonstrated with 3-micron technology, and being scaled to 40 GHz and above. In this paper, we will discuss design and performance of some of these components. 1.

We review a new "direct digitization" approach for "digital RF" architectures for software radio. Although direct digitization usually implies the simultaneous digitization of all channels in a particular band at a downconverted IF, we use this term to refer exclusively to the direct digitization of all bands, from near DC to RF. Furthermore, we present results on band selection and digitization of RF signals directly at the carrier frequency with high resolution. These novel approaches are enabled by a superconductor analog-to-digital converter technology using an ultra-fast IC logic known as Rapid Single Flux Quantum (RSFQ) logic, with performance capable of enabling envisioned software radios.

Wireless applications would be less expensive, more flexible, and more robust if they had more digital and less analog circuitry. The problem is implementing digital signal processing at radio frequencies. Conventional data converters (ADCs and DACs) and digital circuits are simply not fast enough, especially at SATCOM frequencies. However, superconductors can provide ultra fast mixed signal and digital circuits with the linearity and dynamic range required for true direct, digital-RF processing. These superconducting circuits are digital ICs based on Josephson junctions and "rapid-single-flux-quantum" logic (RSFQ), where simple circuit switching speeds up to 750 GHz have been demonstrated. This permits direct conversion between analog RF and digital baseband signals, replacing frequency and protocol-specific analog hardware with flexible digital processors. HYPRES recently developed and delivered an X-band All Digital RF Receiver (XADR) prototype system for the US Army CERDEC and PM DCATS. The concept of this ADR is to replace the entire analog RF receive chain between the antenna and the baseband demodulator with a high performance digital RF equivalent. The first XADR prototype system has been successfully demonstrated at the Joint SATCOM engineering Center (JSEC). End to end link testing, over the satellite has been successfully completed using an existing AN/GSC-39 X-band earth terminal, an XTAR satellite, the X-band ADR and a SATCOM modem.