Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE

Physics Of Low Energy Optical Switching

M. Dagenais, Wayne F. Sharfin

Published Sep 22, 1987• 1 citation
Publisher

Abstract

The physics of low-energy optical switching in both ideal and experimental devices is discussed. Guided-wave optical bistable devices are predicted to have the lowest switching energy per unit gain of any optical switching devices. So far, the bistable diode laser amplifier is the only optical device which can switch with the same switching efficiency as the best electronic device.

DOI
10.1117/12.941201

Related papers

Extremely Low Switching Energy Optical Bistable Devices

M. Dagenais, Wayne F. Sharfin

An all-optical bistable device and an electro-optical bistable device, with performances approaching the fundamental statistical limits, are described. In the all-optical approach, the giant nonlinearities associated with bound excitons in CdS are exploited to demonstrate the lowest-switching-energy (< 4 pJ) all-optical bistable device. The device switches in less than 1 ns and fully recovers in less than 2 ns. These times are detector limited. A switching energy of less than 1 fJ is theoretically predicted for an optimized geometry. In the electro-optical approach, an InGaAsP/InP diode laser amplifier is used to demonstrate bistability with less than 6000 photons (< 8 X 10-16 J) incident on the device. The device switches in less than 1 ns and is cascadable since it has a gain of 100. It operates at room temperature and is compatible with diode laser sources.

Optical Engineering•Feb 1, 1986•13 citations

Low-switching energy optical bistable devices

M. Dagenais, Wayne F. Sharfin

We describe two approaches to low-energy switching and optical bistability. In one approach, which is a more fundamental approach, we use the nonlinearity associated with bound excitons in CdS to demonstrate the lowest total switching energy (4 pJ) of any optical device exhibiting two stable output states for the same input intensity.1 Bound excitons were chosen because they are known to have a very large oscillator strength (f = 7), a fast radiative decay (tspont = 500 ps), and they do not diffuse in the crystal, thus permitting a sharp focusing geometry. Furthermore, they are a good approximation to quantum dots. In a different experiment we have operated a standard diode laser structure below threshold and have demonstrated an efficient optical switch that can be used in thresholding and decision-making applications. The device switches with <400 aJ (4 × 10−16 J or <3000 photons) of optical energy incident on the device.2 During the switching operation, only 10 pJ of electrical power is dissipated. The switch operates at room temperature, is compatible with optical communication systems, and has a gain of the order of 15 dB, leading to the important properties of cascadability and large fan-out. The operation of a high contrast (5:1) AND gate was demonstrated.

Annual Meeting Optical Society of America•Jan 1, 1986•0 citations

Optical Bistability And Switching By Non Inear Waveguiding In Semiconductor Lasers And Laser Amplifiers

John Gerard McInerney, Yuan Li, Theodore C. Salvi +1 more

Bistable optical devices (BODs) are interesting for optical switching, limiting, memory, signal conditioning and logic [1]. Semiconductor-based BODs are especially promising because their large nonlinearities should permit development of compact, rugged and efficient systems. Here we concentrate on active semiconductor BODs and switches, that is those which have internal gain, such as injection lasers and amplifiers.

Digest on Nonlinear Optics: Materials, Phenomena and Devices•Jan 1, 1990•1 citation

Demonstration Of Cascadability And Spectral Bistability In Bistable Diode Laser Amplifiers

Zeqi Pan, T. N. Ding, M. Dagenais

We report the demonstration of cascadability in bistable diode laser amplifiers operated below threshold. A schematic of the experimental set-up is shown in Figure 1. There it is shown that the optical input to the first bistable diode laser amplifier is modulated by a mechanical chopper at frequency Ω1. The output from the first bistable diode laser amplifier is then modulated at Ω2= 2Ω1using a second mechanical chopper. The light is thereafter used as the input to the second bistable device. When the input intensity to the second device is higher than a certain threshold, the output switches. These results are shown in Figure 2. For these experiments, each of the bistable diode laser amplifiers were carefully studied. Detailed bistability measurements at different bias currents and different cavity detuning's were performed. It was found that both the bistability loop and the switching power gets larger as the detuning increases. The size of the hysteresis loop also increased as the laser was operated closer to threshold. In a two beam experiment, it was found that the switching power in the data beam can be as small as 25 nW. Gains larger than 1000 have been demonstrated, indicating the large fan-out capability of these devices. The turn-on and turn-off times in these bistable diode laser amplifiers was measured to be faster than 1 ns and detector limited. These bistable diode laser amplifiers are the most efficient optical devices that have yet been demonstrated and will find applications in photonic switching networks.

Digest on Nonlinear Optics: Materials, Phenomena and Devices•Jan 1, 1990•0 citations

Diode laser based optical logic devices

M. Dagenais

Dispersive optical bistability is reviewed with particular emphasis on trans- mission characteristics, time dependence, cascadability and fan-out capability of bistable diode laser amplifiers. Bistability in inhomogeneously excited diode lasers, gain quenching and polarization bistability are also discussed. Different applica- tions of bistable lasers are then reviewed, including all-optical regeneration, time- division switching, colored optical interconnects, optical crossbar switches and optical look-up tables.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jan 16, 1990•2 citations

Optical Bistability in Semiconductor Laser Amplifiers

M.J. Adams

It has recently become clear that OB in semiconductor laser amplifiers has many potential advantages for applications in optical logic and signal processing. Foremost among these advantages may be listed (i) ready availability (compared with other bistable devices [1]), (ii) wavelength compatibility with optical communications systems, (iii) inherent optical gain (for serial processing), and (iv) a combination of microwatt switching powers and nanosecond switching times leading to femtoule optical switching energies [2,3]. In support of item (ii) on this list, it is worth noting that amplifier OB has been reported at 0.8 μm [4], 1.3 μm [5], and 1.5 μm [6], all of which are wavelengths employed for optical communications systems.

Topical Meeting on Optical Bistability (OB)•Jan 1, 1988•0 citations
The physics of low-energy optical switching in both ideal and experimental devices is discussed. Guided-wave optical bistable devices are predicted to have the lowest switching energy per unit gain of any optical switching devices. So far, the bistable diode laser amplifier is the only optical device which can switch with the same switching efficiency as the best electronic device.
An all-optical bistable device and an electro-optical bistable device, with performances approaching the fundamental statistical limits, are described. In the all-optical approach, the giant nonlinearities associated with bound excitons in CdS are exploited to demonstrate the lowest-switching-energy (< 4 pJ) all-optical bistable device. The device switches in less than 1 ns and fully recovers in less than 2 ns. These times are detector limited. A switching energy of less than 1 fJ is theoretically predicted for an optimized geometry. In the electro-optical approach, an InGaAsP/InP diode laser amplifier is used to demonstrate bistability with less than 6000 photons (< 8 X 10-16 J) incident on the device. The device switches in less than 1 ns and is cascadable since it has a gain of 100. It operates at room temperature and is compatible with diode laser sources.
We describe two approaches to low-energy switching and optical bistability. In one approach, which is a more fundamental approach, we use the nonlinearity associated with bound excitons in CdS to demonstrate the lowest total switching energy (4 pJ) of any optical device exhibiting two stable output states for the same input intensity.1 Bound excitons were chosen because they are known to have a very large oscillator strength (f = 7), a fast radiative decay (tspont = 500 ps), and they do not diffuse in the crystal, thus permitting a sharp focusing geometry. Furthermore, they are a good approximation to quantum dots. In a different experiment we have operated a standard diode laser structure below threshold and have demonstrated an efficient optical switch that can be used in thresholding and decision-making applications. The device switches with <400 aJ (4 × 10−16 J or <3000 photons) of optical energy incident on the device.2 During the switching operation, only 10 pJ of electrical power is dissipated. The switch operates at room temperature, is compatible with optical communication systems, and has a gain of the order of 15 dB, leading to the important properties of cascadability and large fan-out. The operation of a high contrast (5:1) AND gate was demonstrated.
We report the demonstration of cascadability in bistable diode laser amplifiers operated below threshold. A schematic of the experimental set-up is shown in Figure 1. There it is shown that the optical input to the first bistable diode laser amplifier is modulated by a mechanical chopper at frequency Ω1. The output from the first bistable diode laser amplifier is then modulated at Ω2= 2Ω1using a second mechanical chopper. The light is thereafter used as the input to the second bistable device. When the input intensity to the second device is higher than a certain threshold, the output switches. These results are shown in Figure 2. For these experiments, each of the bistable diode laser amplifiers were carefully studied. Detailed bistability measurements at different bias currents and different cavity detuning's were performed. It was found that both the bistability loop and the switching power gets larger as the detuning increases. The size of the hysteresis loop also increased as the laser was operated closer to threshold. In a two beam experiment, it was found that the switching power in the data beam can be as small as 25 nW. Gains larger than 1000 have been demonstrated, indicating the large fan-out capability of these devices. The turn-on and turn-off times in these bistable diode laser amplifiers was measured to be faster than 1 ns and detector limited. These bistable diode laser amplifiers are the most efficient optical devices that have yet been demonstrated and will find applications in photonic switching networks.
Dispersive optical bistability is reviewed with particular emphasis on trans- mission characteristics, time dependence, cascadability and fan-out capability of bistable diode laser amplifiers. Bistability in inhomogeneously excited diode lasers, gain quenching and polarization bistability are also discussed. Different applica- tions of bistable lasers are then reviewed, including all-optical regeneration, time- division switching, colored optical interconnects, optical crossbar switches and optical look-up tables.
It has recently become clear that OB in semiconductor laser amplifiers has many potential advantages for applications in optical logic and signal processing. Foremost among these advantages may be listed (i) ready availability (compared with other bistable devices [1]), (ii) wavelength compatibility with optical communications systems, (iii) inherent optical gain (for serial processing), and (iv) a combination of microwatt switching powers and nanosecond switching times leading to femtoule optical switching energies [2,3]. In support of item (ii) on this list, it is worth noting that amplifier OB has been reported at 0.8 μm [4], 1.3 μm [5], and 1.5 μm [6], all of which are wavelengths employed for optical communications systems.