Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

Low noise in a diffusion-cooled hot-electron mixer at 2.5 THz

Boris S. Karasik, Michael C. Gaidis, William R. McGrath, B. Bumble, Henry George LeDuc

Published Sep 15, 1997• 79 citations
Publisher

Abstract

The noise performance of a Nb hot-electron bolometer mixer at 2.5 THz has been investigated. The devices are fabricated from a 12-nm-thick Nb film, and have a 0.30 μm×0.15 μm in-plane size, thus exploiting diffusion as the electron cooling mechanism. The rf coupling was provided by a twin-slot planar antenna on an elliptical Si lens. The experimentally measured double sideband noise temperature of the receiver was as low as 2750±250 K with an estimated mixer noise temperature of ≈900 K. The mixer bandwidth derived from both noise bandwidth and IF impedance measurements was ≈1.4 GHz. These results demonstrate the low-noise operation of the diffusion-cooled bolometer mixer above 2 THz.

DOI
10.1063/1.119967

Related papers

A low-noise 2.5 THz superconductive Nb hot-electron mixer

Boris S. Karasik, Michael C. Gaidis, William R. McGrath +2 more

We report on the development of a quasioptical Nb hot-electron bolometer mixer for a 2.5 THz heterodyne receiver. The devices are fabricated from a 12 nm thick Nb film, and have a 0.30 /spl mu/m/spl times/0.15 /spl mu/m in-plane size, thus exploiting diffusion as the electron cooling mechanism. The rf coupling was provided by a twin-slot planar antenna on an elliptical Si lens. A specially designed 2.5 THz system, using a CO/sub 2/-pumped FIR laser as local oscillator (LO), with rf hot/cold loads enclosed in vacuum to avoid atmospheric absorption, was used in the experiment. The experimentally measured double sideband (DSB) noise temperature of the receiver was as low as /spl les/3000 K, with an estimated mixer noise temperature of /spl ap/750 K. These results demonstrate the operation of the diffusion-cooled bolometer mixer above 2 THz.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•32 citations

HEZ §uperconductive Nb t-Electron Mixer

Boris S. Karasik, B. Bumble

AbstracF-we report on the development of a quasioptical Nb hot-electron bolometer mixer for a 2.5 THz heterodyne receiver. The devices are fabricated from a 12 nm thick Nb film, and have a 0.30 ~mx0.15 pm in-plane size, thus exploiting diffusion as the electron cooling mechanism. The rf coupling was provided by a twin-slot planar antenna on an elliptical Si lens. A specially designed 2.5 THz system, using a laser as local oscillator (LO), with rf hotkold loads enclosed in vacuum to avoid atmospheric absorption, was used in the experiment. The experimentally measured double sideband (DSB) noise temperature of the receiver was as low as 53000 K, with an estimated mixer noise temperature of = 750 K. These results demonstrate the operation of the diffusion-cooled bolometer mixer above

•Jan 1, 1997•0 citations

Noise and Bandwidth Measurements of Diffusion-Cooled Nb Hot-Electron Bolometer Mixers at Frequencies Above the Superconductive Energy Gap

Rolf A. Wyss, Boris S. Karasik, William R. McGrath +2 more

Diffusion-cooled Nb hot-electron bolometer (HEB) mixers have the potential to simultaneously achieve high intermediate frequency (IF) bandwidths and low mixer noise temperatures for operation at THz frequencies (above the superconductive gap energy). We have measured the IF signal bandwidth at 630 GHz of Nb devices with lengths L = 0.3, 0.2, and 0.1 micrometer in a quasioptical mixer configuration employing twin-slot antennas. The 3-dB EF bandwidth increased from 1.2 GHz for the 0.3 gm long device to 9.2 GHz for the 0.1 gm long device. These results demonstrate the expected 1/L squared dependence of the IF bandwidth at submillimeter wave frequencies for the first time, as well as the largest EF bandwidth obtained to date. For the 0.1 gm device, which had the largest bandwidth, the double sideband (DSB) noise temperature of the receiver was 320-470 K at 630 GHz with an absorbed LO power of 35 nW, estimated using the isothermal method. A version of this mixer with the antenna length scaled for operation at 2.5 THz has also been tested. A DSB receiver noise temperature of 1800 plus or minus 100 K was achieved, which is about 1,000 K lower than our previously reported results. These results demonstrate that large EF bandwidth and low-noise operation of a diffusion-cooled HEB mixer is possible at THz frequencies with the same device geometry.

Softwaretechnik-Trends•Jan 1, 1999•20 citations

A Low-Noise Superconductive Nb Hot-Electron Mixer at 2.5 THz

Boris S. Karasik, Michael C. Gaidis, William R. McGrath +2 more

We report on the development of a quasioptical Nb hot-electron bolometer mixer for a2.5 THz heterodyne receiver. The devices are fabricated from a 12 nm thick Nb film, and have a0.30 gmx0.15 gm in-plane size, thus exploiting diffusion as the electron cooling mechanism. Therf coupling was provided by a tvvin-slot planar antenna on an elliptical Si lens. A speciallydesigned 2.5 THz system, using a CO

•Jan 1, 1997•5 citations

Superconductive hot-electron mixers for terahertz heterodyne receiver applications

William R. McGrath, Anders J. Skalare, Boris S. Karasik +6 more

We report on the development of quasioptical Nb hot-electron bolometer mixers for heterodyne receivers operating at 1 THz 3 THz. The devices have submicron in-plane sizes, thus exploiting diffusion as the electron cooling mechanism. Quasioptical mixer circuits have been developed with planar double-dipole or twin-slot antennas. The measured (DSB) receiver noise temperatures are 1670 K at 1.1 THz, with an estimated mixer noise temperature of approximately equals 1060 K, and 2750 K at 2.5 THz, with an estimated mixer noise temperature of approximately equals 900 K. The IF bandwidth is found to scale as the length-squared, and bandwidths as high as 8 GHz have been measured. These results demonstrate the low-noise, broadband operation of the diffusion-cooled bolometer mixer over a wide range of far-infrared wavelengths.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jul 31, 1998•4 citations

Noise bandwidth of diffusion-cooled hot-electron bolometers

R. J. Schoelkopf, Peter John Burke, D. E. Prober +6 more

We present studies of the input and output noise of diffusion cooled hot-electron bolometer mixers. By simultaneously measuring the gain and noise (with a 14 GHz LO) as a function of intermediate frequency for a 0.16 /spl mu/m diffusion cooled Nb device, we show that the noise bandwidth (4 GHz) is larger than the gain bandwidth (2.4 GHz). The output noise is 55 K, and the mixer noise is very low, 340 K DSB. This shows that diffusion cooled devices have low noise over a broad enough intermediate frequency band for practical applications in THz receivers.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•6 citations
The noise performance of a Nb hot-electron bolometer mixer at 2.5 THz has been investigated. The devices are fabricated from a 12-nm-thick Nb film, and have a 0.30 μm×0.15 μm in-plane size, thus exploiting diffusion as the electron cooling mechanism. The rf coupling was provided by a twin-slot planar antenna on an elliptical Si lens. The experimentally measured double sideband noise temperature of the receiver was as low as 2750±250 K with an estimated mixer noise temperature of ≈900 K. The mixer bandwidth derived from both noise bandwidth and IF impedance measurements was ≈1.4 GHz. These results demonstrate the low-noise operation of the diffusion-cooled bolometer mixer above 2 THz.
We report on the development of a quasioptical Nb hot-electron bolometer mixer for a 2.5 THz heterodyne receiver. The devices are fabricated from a 12 nm thick Nb film, and have a 0.30 /spl mu/m/spl times/0.15 /spl mu/m in-plane size, thus exploiting diffusion as the electron cooling mechanism. The rf coupling was provided by a twin-slot planar antenna on an elliptical Si lens. A specially designed 2.5 THz system, using a CO/sub 2/-pumped FIR laser as local oscillator (LO), with rf hot/cold loads enclosed in vacuum to avoid atmospheric absorption, was used in the experiment. The experimentally measured double sideband (DSB) noise temperature of the receiver was as low as /spl les/3000 K, with an estimated mixer noise temperature of /spl ap/750 K. These results demonstrate the operation of the diffusion-cooled bolometer mixer above 2 THz.
AbstracF-we report on the development of a quasioptical Nb hot-electron bolometer mixer for a 2.5 THz heterodyne receiver. The devices are fabricated from a 12 nm thick Nb film, and have a 0.30 ~mx0.15 pm in-plane size, thus exploiting diffusion as the electron cooling mechanism. The rf coupling was provided by a twin-slot planar antenna on an elliptical Si lens. A specially designed 2.5 THz system, using a laser as local oscillator (LO), with rf hotkold loads enclosed in vacuum to avoid atmospheric absorption, was used in the experiment. The experimentally measured double sideband (DSB) noise temperature of the receiver was as low as 53000 K, with an estimated mixer noise temperature of = 750 K. These results demonstrate the operation of the diffusion-cooled bolometer mixer above
Diffusion-cooled Nb hot-electron bolometer (HEB) mixers have the potential to simultaneously achieve high intermediate frequency (IF) bandwidths and low mixer noise temperatures for operation at THz frequencies (above the superconductive gap energy). We have measured the IF signal bandwidth at 630 GHz of Nb devices with lengths L = 0.3, 0.2, and 0.1 micrometer in a quasioptical mixer configuration employing twin-slot antennas. The 3-dB EF bandwidth increased from 1.2 GHz for the 0.3 gm long device to 9.2 GHz for the 0.1 gm long device. These results demonstrate the expected 1/L squared dependence of the IF bandwidth at submillimeter wave frequencies for the first time, as well as the largest EF bandwidth obtained to date. For the 0.1 gm device, which had the largest bandwidth, the double sideband (DSB) noise temperature of the receiver was 320-470 K at 630 GHz with an absorbed LO power of 35 nW, estimated using the isothermal method. A version of this mixer with the antenna length scaled for operation at 2.5 THz has also been tested. A DSB receiver noise temperature of 1800 plus or minus 100 K was achieved, which is about 1,000 K lower than our previously reported results. These results demonstrate that large EF bandwidth and low-noise operation of a diffusion-cooled HEB mixer is possible at THz frequencies with the same device geometry.
We report on the development of quasioptical Nb hot-electron bolometer mixers for heterodyne receivers operating at 1 THz 3 THz. The devices have submicron in-plane sizes, thus exploiting diffusion as the electron cooling mechanism. Quasioptical mixer circuits have been developed with planar double-dipole or twin-slot antennas. The measured (DSB) receiver noise temperatures are 1670 K at 1.1 THz, with an estimated mixer noise temperature of approximately equals 1060 K, and 2750 K at 2.5 THz, with an estimated mixer noise temperature of approximately equals 900 K. The IF bandwidth is found to scale as the length-squared, and bandwidths as high as 8 GHz have been measured. These results demonstrate the low-noise, broadband operation of the diffusion-cooled bolometer mixer over a wide range of far-infrared wavelengths.
We present studies of the input and output noise of diffusion cooled hot-electron bolometer mixers. By simultaneously measuring the gain and noise (with a 14 GHz LO) as a function of intermediate frequency for a 0.16 /spl mu/m diffusion cooled Nb device, we show that the noise bandwidth (4 GHz) is larger than the gain bandwidth (2.4 GHz). The output noise is 55 K, and the mixer noise is very low, 340 K DSB. This shows that diffusion cooled devices have low noise over a broad enough intermediate frequency band for practical applications in THz receivers.