Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

A Low-Noise Superconductive Nb Hot-Electron Mixer at 2.5 THz

Boris S. Karasik, Michael C. Gaidis, William R. McGrath, B. Bumble, Henry George LeDuc

Published Jan 1, 1997• 5 citations
OpenAlex

Abstract

We report on the development of a quasioptical Nb hot-electron bolometer mixer for a2.5 THz heterodyne receiver. The devices are fabricated from a 12 nm thick Nb film, and have a0.30 gmx0.15 gm in-plane size, thus exploiting diffusion as the electron cooling mechanism. Therf coupling was provided by a tvvin-slot planar antenna on an elliptical Si lens. A speciallydesigned 2.5 THz system, using a CO

Related papers

A low-noise 2.5 THz superconductive Nb hot-electron mixer

Boris S. Karasik, Michael C. Gaidis, William R. McGrath +2 more

We report on the development of a quasioptical Nb hot-electron bolometer mixer for a 2.5 THz heterodyne receiver. The devices are fabricated from a 12 nm thick Nb film, and have a 0.30 /spl mu/m/spl times/0.15 /spl mu/m in-plane size, thus exploiting diffusion as the electron cooling mechanism. The rf coupling was provided by a twin-slot planar antenna on an elliptical Si lens. A specially designed 2.5 THz system, using a CO/sub 2/-pumped FIR laser as local oscillator (LO), with rf hot/cold loads enclosed in vacuum to avoid atmospheric absorption, was used in the experiment. The experimentally measured double sideband (DSB) noise temperature of the receiver was as low as /spl les/3000 K, with an estimated mixer noise temperature of /spl ap/750 K. These results demonstrate the operation of the diffusion-cooled bolometer mixer above 2 THz.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•32 citations

HEZ §uperconductive Nb t-Electron Mixer

Boris S. Karasik, B. Bumble

AbstracF-we report on the development of a quasioptical Nb hot-electron bolometer mixer for a 2.5 THz heterodyne receiver. The devices are fabricated from a 12 nm thick Nb film, and have a 0.30 ~mx0.15 pm in-plane size, thus exploiting diffusion as the electron cooling mechanism. The rf coupling was provided by a twin-slot planar antenna on an elliptical Si lens. A specially designed 2.5 THz system, using a laser as local oscillator (LO), with rf hotkold loads enclosed in vacuum to avoid atmospheric absorption, was used in the experiment. The experimentally measured double sideband (DSB) noise temperature of the receiver was as low as 53000 K, with an estimated mixer noise temperature of = 750 K. These results demonstrate the operation of the diffusion-cooled bolometer mixer above

•Jan 1, 1997•0 citations

Low noise in a diffusion-cooled hot-electron mixer at 2.5 THz

Boris S. Karasik, Michael C. Gaidis, William R. McGrath +2 more

The noise performance of a Nb hot-electron bolometer mixer at 2.5 THz has been investigated. The devices are fabricated from a 12-nm-thick Nb film, and have a 0.30 μm×0.15 μm in-plane size, thus exploiting diffusion as the electron cooling mechanism. The rf coupling was provided by a twin-slot planar antenna on an elliptical Si lens. The experimentally measured double sideband noise temperature of the receiver was as low as 2750±250 K with an estimated mixer noise temperature of ≈900 K. The mixer bandwidth derived from both noise bandwidth and IF impedance measurements was ≈1.4 GHz. These results demonstrate the low-noise operation of the diffusion-cooled bolometer mixer above 2 THz.

Applied Physics Letters•Sep 15, 1997•79 citations

Superconductive hot-electron mixers for terahertz heterodyne receiver applications

William R. McGrath, Anders J. Skalare, Boris S. Karasik +6 more

We report on the development of quasioptical Nb hot-electron bolometer mixers for heterodyne receivers operating at 1 THz 3 THz. The devices have submicron in-plane sizes, thus exploiting diffusion as the electron cooling mechanism. Quasioptical mixer circuits have been developed with planar double-dipole or twin-slot antennas. The measured (DSB) receiver noise temperatures are 1670 K at 1.1 THz, with an estimated mixer noise temperature of approximately equals 1060 K, and 2750 K at 2.5 THz, with an estimated mixer noise temperature of approximately equals 900 K. The IF bandwidth is found to scale as the length-squared, and bandwidths as high as 8 GHz have been measured. These results demonstrate the low-noise, broadband operation of the diffusion-cooled bolometer mixer over a wide range of far-infrared wavelengths.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jul 31, 1998•4 citations

Heterodyne measurements of a NbN superconducting hot electron mixer at terahertz frequencies

Pavel A. Yagoubov, M. Kroug, H. Merkel +6 more

The performance of a NbN based phonon-cooled Hot Electron Bolometric (HEB) quasioptical mixer is investigated in the 0.65-3.12 THz frequency range. The device is made from a 3 nm thick NbN film on high resistivity Si and integrated with a planar spiral antenna on the same substrate. The in-plane dimensions of the bolometer strip are 0.2/spl times/2 /spl mu/m. The best results of the DSB noise temperature at 1.5 GHz IF frequency obtained with one device are: 1300 K at 650 GHz, 4700 K at 2.5 THz and 10000 K at 3.12 THz. The measurements were performed at 4.5 K ambient temperature. The amount of local oscillator (LO) power absorbed in the bolometer is about 100 nW. The mixer is linear to within 1 dB compression up to the signal level 10 dB below that of the LO. The intrinsic single sideband conversion gain measured at 650 GHz is -9 dB, the total conversion gain is -14 dB.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•6 citations

NbN Hot Electron Bolometric Mixers for a Quasi--Optical THz Receiver

M. Kroug

Experimental work on the development of a quasi-optical heterodyne receiver for the THz frequency range is reported. The mixing device is a superconducting hot electron bolometer (HEB) made from ultrathin, d = 3 - 5 nm, niobium nitride (NbN) films. Work described in this thesis comprises: The design of a prototype receiver using quasi-optical coupling. Device fabrication involving reactive magnetron sputtering of NbN films and lithographic definition of the antenna integrated mixer. An investigation of the receiver performance at frequencies between 0.6 THz and 2.5 THz. The best performance is obtained with HEB mixers made from NbN films with a thickness d = 3-3.5 nm and a critical temperature T c = 9 - 9.5 K. Double-side band receiver noise temperatures are 530 K at 0.6 THz, 650 K at 1.6 THz and 1100 K at 2.5 THz. Corrected for losses in the receiver input optics, these values amount to only 10 times the theoretical quantum limit. MgO as the substrate material has been shown to provide improved acoustic coupling between NbN film and the substrate compared to other materials such as Si or sapphire. A maximum IF gain bandwidth of 4.5 GHz has been measured under the same operating conditions which yield lowest noise temperature. The local oscilltor power requirement is ~250 nW absorbed in the bolometer. Quasi-optically coupled HEB mixers have become the device-of-choice for radio astronomical applications in the frequency regime at and above 1 THz.

•Jan 1, 2001•4 citations
We report on the development of a quasioptical Nb hot-electron bolometer mixer for a2.5 THz heterodyne receiver. The devices are fabricated from a 12 nm thick Nb film, and have a0.30 gmx0.15 gm in-plane size, thus exploiting diffusion as the electron cooling mechanism. Therf coupling was provided by a tvvin-slot planar antenna on an elliptical Si lens. A speciallydesigned 2.5 THz system, using a CO
We report on the development of a quasioptical Nb hot-electron bolometer mixer for a 2.5 THz heterodyne receiver. The devices are fabricated from a 12 nm thick Nb film, and have a 0.30 /spl mu/m/spl times/0.15 /spl mu/m in-plane size, thus exploiting diffusion as the electron cooling mechanism. The rf coupling was provided by a twin-slot planar antenna on an elliptical Si lens. A specially designed 2.5 THz system, using a CO/sub 2/-pumped FIR laser as local oscillator (LO), with rf hot/cold loads enclosed in vacuum to avoid atmospheric absorption, was used in the experiment. The experimentally measured double sideband (DSB) noise temperature of the receiver was as low as /spl les/3000 K, with an estimated mixer noise temperature of /spl ap/750 K. These results demonstrate the operation of the diffusion-cooled bolometer mixer above 2 THz.
AbstracF-we report on the development of a quasioptical Nb hot-electron bolometer mixer for a 2.5 THz heterodyne receiver. The devices are fabricated from a 12 nm thick Nb film, and have a 0.30 ~mx0.15 pm in-plane size, thus exploiting diffusion as the electron cooling mechanism. The rf coupling was provided by a twin-slot planar antenna on an elliptical Si lens. A specially designed 2.5 THz system, using a laser as local oscillator (LO), with rf hotkold loads enclosed in vacuum to avoid atmospheric absorption, was used in the experiment. The experimentally measured double sideband (DSB) noise temperature of the receiver was as low as 53000 K, with an estimated mixer noise temperature of = 750 K. These results demonstrate the operation of the diffusion-cooled bolometer mixer above
The noise performance of a Nb hot-electron bolometer mixer at 2.5 THz has been investigated. The devices are fabricated from a 12-nm-thick Nb film, and have a 0.30 μm×0.15 μm in-plane size, thus exploiting diffusion as the electron cooling mechanism. The rf coupling was provided by a twin-slot planar antenna on an elliptical Si lens. The experimentally measured double sideband noise temperature of the receiver was as low as 2750±250 K with an estimated mixer noise temperature of ≈900 K. The mixer bandwidth derived from both noise bandwidth and IF impedance measurements was ≈1.4 GHz. These results demonstrate the low-noise operation of the diffusion-cooled bolometer mixer above 2 THz.
We report on the development of quasioptical Nb hot-electron bolometer mixers for heterodyne receivers operating at 1 THz 3 THz. The devices have submicron in-plane sizes, thus exploiting diffusion as the electron cooling mechanism. Quasioptical mixer circuits have been developed with planar double-dipole or twin-slot antennas. The measured (DSB) receiver noise temperatures are 1670 K at 1.1 THz, with an estimated mixer noise temperature of approximately equals 1060 K, and 2750 K at 2.5 THz, with an estimated mixer noise temperature of approximately equals 900 K. The IF bandwidth is found to scale as the length-squared, and bandwidths as high as 8 GHz have been measured. These results demonstrate the low-noise, broadband operation of the diffusion-cooled bolometer mixer over a wide range of far-infrared wavelengths.
The performance of a NbN based phonon-cooled Hot Electron Bolometric (HEB) quasioptical mixer is investigated in the 0.65-3.12 THz frequency range. The device is made from a 3 nm thick NbN film on high resistivity Si and integrated with a planar spiral antenna on the same substrate. The in-plane dimensions of the bolometer strip are 0.2/spl times/2 /spl mu/m. The best results of the DSB noise temperature at 1.5 GHz IF frequency obtained with one device are: 1300 K at 650 GHz, 4700 K at 2.5 THz and 10000 K at 3.12 THz. The measurements were performed at 4.5 K ambient temperature. The amount of local oscillator (LO) power absorbed in the bolometer is about 100 nW. The mixer is linear to within 1 dB compression up to the signal level 10 dB below that of the LO. The intrinsic single sideband conversion gain measured at 650 GHz is -9 dB, the total conversion gain is -14 dB.
Experimental work on the development of a quasi-optical heterodyne receiver for the THz frequency range is reported. The mixing device is a superconducting hot electron bolometer (HEB) made from ultrathin, d = 3 - 5 nm, niobium nitride (NbN) films. Work described in this thesis comprises: The design of a prototype receiver using quasi-optical coupling. Device fabrication involving reactive magnetron sputtering of NbN films and lithographic definition of the antenna integrated mixer. An investigation of the receiver performance at frequencies between 0.6 THz and 2.5 THz. The best performance is obtained with HEB mixers made from NbN films with a thickness d = 3-3.5 nm and a critical temperature T c = 9 - 9.5 K. Double-side band receiver noise temperatures are 530 K at 0.6 THz, 650 K at 1.6 THz and 1100 K at 2.5 THz. Corrected for losses in the receiver input optics, these values amount to only 10 times the theoretical quantum limit. MgO as the substrate material has been shown to provide improved acoustic coupling between NbN film and the substrate compared to other materials such as Si or sapphire. A maximum IF gain bandwidth of 4.5 GHz has been measured under the same operating conditions which yield lowest noise temperature. The local oscilltor power requirement is ~250 nW absorbed in the bolometer. Quasi-optically coupled HEB mixers have become the device-of-choice for radio astronomical applications in the frequency regime at and above 1 THz.