Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Wiley eBooks

Micro‐Fabricated Chip Traps for Ions

Jason Amini, J. Britton, Dietrich G. Leibfried, David J. Wineland

Published Feb 9, 2011• 28 citations
Publisher

Abstract

This chapter discusses the trapping of atomic ions. Microfabrication holds the promise of forming large arrays of traps that would allow the scaling of current quantum information processing capabilities to the level needed to implement useful algorithms. The chapter provides an introduction to the dynamics of ions confined in Paul traps based on the pseudopotential approximation. It includes numeric and analytic models for various Paul trap geometries, a list of considerations for practical trap design, and provides an overview of micro-fabricated trapping structures. The chapter discusses the equations of motion of a charged particle in a spatially inhomogeneous RF field based on the pseudopotential approximation model. It presents examples of suitable electrode geometries. Amethod to measure ion motional heating with a single low-power laser beam is outlined. Controlled Vocabulary Terms atoms; electron traps; heating elements; optical information processing; particle traps

DOI
10.1002/9783527633357.ch13

Related papers

The development of microfabricated ion traps towards quantum information and simulation

Marcus Hughes

Trapped ions within Paul traps have shown to be a promising architecture in the realisation of a quantum information processor together with the ability of providing quantum simulations. Linear Paul traps have demonstrated long coherence times with ions being well isolated from the environment, single and multi-qubit gates and the high fidelity detection of states. The scalability to large number of qubits, incorporating all the previous achievements requires an array of linear ion traps. Microfabrication techniques allow for fabrication and micron level accuracy of the trap electrode dimensions through photolithography techniques. The first part of this thesis presents the experiential setup and trapping of Yb+ ions needed to test large ion trap arrays. This include vacuum systems that can host advanced symmetric and asymmetric ion traps with up to 90 static voltage control electrodes. Demonstration of a single trapped Yb+ ion within a two-layer macroscopic ion trap is presented. with an ion-electrode distance of 310(10) µm. The anomalous heating rate and spectral noise density of the trap was measured, a main form of decoherence within ion traps. The second half of this thesis presents the design and fabrication of multi-layer asymmetric ion traps. This allows for isolated electrodes that cannot be accessed via surface pathways, allowing for higher density of electrodes as well as creating novel trap designs that allow for the potential of quantum simulations to be demonstrated. These include two-dimensional lattices and ring trap designs in which the isolated electrodes provide more control in the ion position. For the microfabrication of these traps I present a novel high-aspect ratio electroplated electrode design that provides shielding of the dielectric layer. This provides a means to mitigate stray electric field due to charge build up on the dielectric surfaces. Electrical testing of the trap structures was performed to test bulk breakdown and surface flashover of the ion trap architectures. Results showed sufficient isolation between electrodes for both radio frequency and static breakdown. Surface flashover voltage measurements over the dielectric layer showed an improvement of more than double over previous results using a new fabrication technique. This will allow for more powerful ion trap chips needed for the next generation of microfabricated ion trap arrays for scalable quantum technologies.

•Jun 16, 2013•0 citations

Microfabricated ion traps

Marcus D. Hughes, Bjoern Lekitsch, Jiddu A. Broersma +1 more

Ion traps offer the opportunity to study fundamental quantum systems with a high level of accuracy highly decoupled from the environment. Individual atomic ions can be controlled and manipulated with electric fields, cooled to the ground state of motion with laser cooling and coherently manipulated using optical and microwave radiation. Microfabricated ion traps hold the advantage of allowing for smaller trap dimensions and better scalability towards large ion trap arrays also making them a vital ingredient for next generation quantum technologies. Here we provide an introduction into the principles and operation of microfabricated ion traps. We show an overview of material and electrical considerations which are vital for the design of such trap structures. We provide guidance on how to choose the appropriate fabrication design, consider different methods for the fabrication of microfabricated ion traps and discuss previously realised structures. We also discuss the phenomenon of anomalous heating of ions within ion traps, which becomes an important factor in the miniaturisation of ion traps.

arXiv:1101.3207•Contemporary Physics•Sep 16, 2011•81 citations

Microfabricated Surface-Electrode Ion Trap for Scalable Quantum Information Processing

Signe Louise Seidelin, John Chiaverini, R. Reichle +13 more

Individual laser-cooled 24Mg+ ions are confined in a linear Paul trap with a novel geometry where gold electrodes are located in a single plane and the ions are trapped 40 microm above this plane. The relatively simple trap design and fabrication procedure are important for large-scale quantum information processing (QIP) using ions. Measured ion motional frequencies are compared to simulations. Measurements of ion recooling after cooling is temporarily suspended yield a heating rate of approximately 5 motional quanta per millisecond for a trap frequency of 2.83 MHz, sufficiently low to be useful for QIP.

arXiv:quant-ph/0601173•Physical Review Letters•Jun 30, 2006•457 citations

Atom Chip Fabrication

R. Folman, Philipp Treutlein, Jörg Schmiedmayer

This chapter overviews atom chip fabrication by discussing the challenges to be faced when starting to conceive and fabricate chips for the manipulation of atoms. It describes the various ingredients and the corresponding fabrication methods. The chapter focuses not only on the currently most active and successful areas - current carrying wires and integrated photonics, but also focuses on more visionary approaches, examples being superconducting chips or the manipulation of atoms with real nanostructures such as carbon nanotubes. It discusses the material engineering and fabrication of atom chips for the manipulation of neutral atoms, but the same concept of robustness and versatility through miniaturization and integration can also be applied to manipulate molecules, ions, or trapped electrons. Metallic wires, electrodes, or permanent magnets are the most commonly used structures on an atom chip. In lithography, a pattern is transferred into a layer of resist on the chip surface. Controlled Vocabulary Terms electron beam lithography; metallic thin films; microfabrication

Wiley eBooks•Feb 9, 2011•10 citations

Fabrication and Characterization of Semiconductor Ion Traps for Quantum Information Processing.

Daniel Stick

The electromagnetic manipulation of isolated ions has led to many advances in atomic physics, from laser cooling to precision metrology and quantum control. As technical capability in this area has grown, so has interest in building miniature electromagnetic traps for the development of large-scale quantum information processors. This thesis will primarily focus on using microfabrication techniques to build arrays of miniature ion traps, similar to techniques used in fabricating high component density microprocessors. A specific focus will be on research using a gallium arsenide/aluminum gallium arsenide heterostructure as a trap architecture, as well as the recent testing of different ion traps fabricated at outside foundries. The construction and characterization of a conventional ceramic trap capable of shuttling an ion through a junction will also be detailed, and reveal the need for moving towards lithographically fabricated traps. Combined, these serve as a set of proof-of-principle experiments pointing to methods for designing and building large scale arrays of ion traps capable of constituting a quantum information processor. As traps become smaller, electrical potentials on the electrodes have greater influence on the ion. This not only pertains to intentionally applied voltages, but also to deleterious noise sources, such as thermal Johnson noise and the more significant ``patch potential" noise, which both cause motional heating of the ion. These problematic noise sources dovetail with my thesis research into trap miniaturization since their effects become more pronounced and impossible to ignore for small trap sizes. Therefore characterizing them and investigating ways to suppress them have become an important component of my research. I will describe an experiment using a pair of movable needle electrodes to measure the ion heating rate corresponding to the harmonic frequency of the trap, the ion-electrode distance, and the electrode temperature. This information is used for characterizing the fluctuating potentials and exploring the possibility of suppressing motional heating by cooling the trap electrodes. This source of noise is also observed in other systems, and its characterization could potentially improve other precision experiments, such as those measuring deviations in the gravitational inverse square law with proximate masses.

•Jan 1, 2007•4 citations

A microfabricated surface-electrode ion trap in silicon

J. Britton, Dietrich G. Leibfried, James A. Beall +13 more

The prospect of building a quantum information processor underlies many recent advances ion trap fabrication techniques. Potentially, a quantum computer could be constructed from a large array of interconnected ion traps. We report on a micrometer-scale ion trap, fabricated from bulk silicon using micro-electromechanical systems (MEMS) techniques. The trap geometry is relatively simple in that the electrodes lie in a single plane beneath the ions. In such a trap we confine laser-cooled 24Mg+ ions approximately 40 microns above the surface. The fabrication technique and planar electrode geometry together make this approach amenable to scaling up to large trap arrays. In addition we observe that little laser cooling light is scattered by the electrodes.

arXiv:quant-ph/0605170•May 19, 2006•39 citations
This chapter discusses the trapping of atomic ions. Microfabrication holds the promise of forming large arrays of traps that would allow the scaling of current quantum information processing capabilities to the level needed to implement useful algorithms. The chapter provides an introduction to the dynamics of ions confined in Paul traps based on the pseudopotential approximation. It includes numeric and analytic models for various Paul trap geometries, a list of considerations for practical trap design, and provides an overview of micro-fabricated trapping structures. The chapter discusses the equations of motion of a charged particle in a spatially inhomogeneous RF field based on the pseudopotential approximation model. It presents examples of suitable electrode geometries. Amethod to measure ion motional heating with a single low-power laser beam is outlined. Controlled Vocabulary Terms atoms; electron traps; heating elements; optical information processing; particle traps
Trapped ions within Paul traps have shown to be a promising architecture in the realisation of a quantum information processor together with the ability of providing quantum simulations. Linear Paul traps have demonstrated long coherence times with ions being well isolated from the environment, single and multi-qubit gates and the high fidelity detection of states. The scalability to large number of qubits, incorporating all the previous achievements requires an array of linear ion traps. Microfabrication techniques allow for fabrication and micron level accuracy of the trap electrode dimensions through photolithography techniques. The first part of this thesis presents the experiential setup and trapping of Yb+ ions needed to test large ion trap arrays. This include vacuum systems that can host advanced symmetric and asymmetric ion traps with up to 90 static voltage control electrodes. Demonstration of a single trapped Yb+ ion within a two-layer macroscopic ion trap is presented. with an ion-electrode distance of 310(10) µm. The anomalous heating rate and spectral noise density of the trap was measured, a main form of decoherence within ion traps. The second half of this thesis presents the design and fabrication of multi-layer asymmetric ion traps. This allows for isolated electrodes that cannot be accessed via surface pathways, allowing for higher density of electrodes as well as creating novel trap designs that allow for the potential of quantum simulations to be demonstrated. These include two-dimensional lattices and ring trap designs in which the isolated electrodes provide more control in the ion position. For the microfabrication of these traps I present a novel high-aspect ratio electroplated electrode design that provides shielding of the dielectric layer. This provides a means to mitigate stray electric field due to charge build up on the dielectric surfaces. Electrical testing of the trap structures was performed to test bulk breakdown and surface flashover of the ion trap architectures. Results showed sufficient isolation between electrodes for both radio frequency and static breakdown. Surface flashover voltage measurements over the dielectric layer showed an improvement of more than double over previous results using a new fabrication technique. This will allow for more powerful ion trap chips needed for the next generation of microfabricated ion trap arrays for scalable quantum technologies.
Ion traps offer the opportunity to study fundamental quantum systems with a high level of accuracy highly decoupled from the environment. Individual atomic ions can be controlled and manipulated with electric fields, cooled to the ground state of motion with laser cooling and coherently manipulated using optical and microwave radiation. Microfabricated ion traps hold the advantage of allowing for smaller trap dimensions and better scalability towards large ion trap arrays also making them a vital ingredient for next generation quantum technologies. Here we provide an introduction into the principles and operation of microfabricated ion traps. We show an overview of material and electrical considerations which are vital for the design of such trap structures. We provide guidance on how to choose the appropriate fabrication design, consider different methods for the fabrication of microfabricated ion traps and discuss previously realised structures. We also discuss the phenomenon of anomalous heating of ions within ion traps, which becomes an important factor in the miniaturisation of ion traps.
Individual laser-cooled 24Mg+ ions are confined in a linear Paul trap with a novel geometry where gold electrodes are located in a single plane and the ions are trapped 40 microm above this plane. The relatively simple trap design and fabrication procedure are important for large-scale quantum information processing (QIP) using ions. Measured ion motional frequencies are compared to simulations. Measurements of ion recooling after cooling is temporarily suspended yield a heating rate of approximately 5 motional quanta per millisecond for a trap frequency of 2.83 MHz, sufficiently low to be useful for QIP.
This chapter overviews atom chip fabrication by discussing the challenges to be faced when starting to conceive and fabricate chips for the manipulation of atoms. It describes the various ingredients and the corresponding fabrication methods. The chapter focuses not only on the currently most active and successful areas - current carrying wires and integrated photonics, but also focuses on more visionary approaches, examples being superconducting chips or the manipulation of atoms with real nanostructures such as carbon nanotubes. It discusses the material engineering and fabrication of atom chips for the manipulation of neutral atoms, but the same concept of robustness and versatility through miniaturization and integration can also be applied to manipulate molecules, ions, or trapped electrons. Metallic wires, electrodes, or permanent magnets are the most commonly used structures on an atom chip. In lithography, a pattern is transferred into a layer of resist on the chip surface. Controlled Vocabulary Terms electron beam lithography; metallic thin films; microfabrication
The electromagnetic manipulation of isolated ions has led to many advances in atomic physics, from laser cooling to precision metrology and quantum control. As technical capability in this area has grown, so has interest in building miniature electromagnetic traps for the development of large-scale quantum information processors. This thesis will primarily focus on using microfabrication techniques to build arrays of miniature ion traps, similar to techniques used in fabricating high component density microprocessors. A specific focus will be on research using a gallium arsenide/aluminum gallium arsenide heterostructure as a trap architecture, as well as the recent testing of different ion traps fabricated at outside foundries. The construction and characterization of a conventional ceramic trap capable of shuttling an ion through a junction will also be detailed, and reveal the need for moving towards lithographically fabricated traps. Combined, these serve as a set of proof-of-principle experiments pointing to methods for designing and building large scale arrays of ion traps capable of constituting a quantum information processor. As traps become smaller, electrical potentials on the electrodes have greater influence on the ion. This not only pertains to intentionally applied voltages, but also to deleterious noise sources, such as thermal Johnson noise and the more significant ``patch potential" noise, which both cause motional heating of the ion. These problematic noise sources dovetail with my thesis research into trap miniaturization since their effects become more pronounced and impossible to ignore for small trap sizes. Therefore characterizing them and investigating ways to suppress them have become an important component of my research. I will describe an experiment using a pair of movable needle electrodes to measure the ion heating rate corresponding to the harmonic frequency of the trap, the ion-electrode distance, and the electrode temperature. This information is used for characterizing the fluctuating potentials and exploring the possibility of suppressing motional heating by cooling the trap electrodes. This source of noise is also observed in other systems, and its characterization could potentially improve other precision experiments, such as those measuring deviations in the gravitational inverse square law with proximate masses.
The prospect of building a quantum information processor underlies many recent advances ion trap fabrication techniques. Potentially, a quantum computer could be constructed from a large array of interconnected ion traps. We report on a micrometer-scale ion trap, fabricated from bulk silicon using micro-electromechanical systems (MEMS) techniques. The trap geometry is relatively simple in that the electrodes lie in a single plane beneath the ions. In such a trap we confine laser-cooled 24Mg+ ions approximately 40 microns above the surface. The fabrication technique and planar electrode geometry together make this approach amenable to scaling up to large trap arrays. In addition we observe that little laser cooling light is scattered by the electrodes.