Trapped ions within Paul traps have shown to be a promising architecture in the realisation of a quantum information processor together with the ability of providing quantum simulations. Linear Paul traps have demonstrated long coherence times with ions being well isolated from the environment, single and multi-qubit gates and the high fidelity detection of states. The scalability to large number of qubits, incorporating all the previous achievements requires an array of linear ion traps. Microfabrication techniques allow for fabrication and micron level accuracy of the trap electrode dimensions through photolithography techniques. The first part of this thesis presents the experiential setup and trapping of Yb+ ions needed to test large ion trap arrays. This include vacuum systems that can host advanced symmetric and asymmetric ion traps with up to 90 static voltage control electrodes. Demonstration of a single trapped Yb+ ion within a two-layer macroscopic ion trap is presented. with an ion-electrode distance of 310(10) µm. The anomalous heating rate and spectral noise density of the trap was measured, a main form of decoherence within ion traps. The second half of this thesis presents the design and fabrication of multi-layer asymmetric ion traps. This allows for isolated electrodes that cannot be accessed via surface pathways, allowing for higher density of electrodes as well as creating novel trap designs that allow for the potential of quantum simulations to be demonstrated. These include two-dimensional lattices and ring trap designs in which the isolated electrodes provide more control in the ion position. For the microfabrication of these traps I present a novel high-aspect ratio electroplated electrode design that provides shielding of the dielectric layer. This provides a means to mitigate stray electric field due to charge build up on the dielectric surfaces. Electrical testing of the trap structures was performed to test bulk breakdown and surface flashover of the ion trap architectures. Results showed sufficient isolation between electrodes for both radio frequency and static breakdown. Surface flashover voltage measurements over the dielectric layer showed an improvement of more than double over previous results using a new fabrication technique. This will allow for more powerful ion trap chips needed for the next generation of microfabricated ion trap arrays for scalable quantum technologies.
Trapped ions within Paul traps have shown to be a promising architecture in the realisation of a quantum information processor together with the ability of providing quantum simulations. Linear Paul traps have demonstrated long coherence times with ions being well isolated from the environment, single and multi-qubit gates and the high fidelity detection of states. The scalability to large number of qubits, incorporating all the previous achievements requires an array of linear ion traps. Microfabrication techniques allow for fabrication and micron level accuracy of the trap electrode dimensions through photolithography techniques. The first part of this thesis presents the experiential setup and trapping of Yb+ ions needed to test large ion trap arrays. This include vacuum systems that can host advanced symmetric and asymmetric ion traps with up to 90 static voltage control electrodes. Demonstration of a single trapped Yb+ ion within a two-layer macroscopic ion trap is presented. with an ion-electrode distance of 310(10) µm. The anomalous heating rate and spectral noise density of the trap was measured, a main form of decoherence within ion traps. The second half of this thesis presents the design and fabrication of multi-layer asymmetric ion traps. This allows for isolated electrodes that cannot be accessed via surface pathways, allowing for higher density of electrodes as well as creating novel trap designs that allow for the potential of quantum simulations to be demonstrated. These include two-dimensional lattices and ring trap designs in which the isolated electrodes provide more control in the ion position. For the microfabrication of these traps I present a novel high-aspect ratio electroplated electrode design that provides shielding of the dielectric layer. This provides a means to mitigate stray electric field due to charge build up on the dielectric surfaces. Electrical testing of the trap structures was performed to test bulk breakdown and surface flashover of the ion trap architectures. Results showed sufficient isolation between electrodes for both radio frequency and static breakdown. Surface flashover voltage measurements over the dielectric layer showed an improvement of more than double over previous results using a new fabrication technique. This will allow for more powerful ion trap chips needed for the next generation of microfabricated ion trap arrays for scalable quantum technologies.
Trapped ions in Paul traps (radio frequency ion traps) are a promising candidate for the realization of a quantum computer. To date, experimental demonstrations of quantum computing and information processing with trapped ions have been limited to small numbers of quantum bits (qubits). The most prominent challenge to realise ion-trap quantum computation is to scale the system and control a large number of trapped ions coherently. Surface-electrode ion trap designs which are amenable to various microfabrication techniques offer a path to achieve this. In this work, design, fabrication and key operations of two types of surface-electrode ion traps, i.e. a Y-junction trap and a two-dimensional (2D) hexagonal lattice trap developed towards scaling ion-trap architectures, are presented. The steps involved in the fabrication of the ion-trap devices included photolithography, wet etch (hydrofluoric acid etch) and dry etch (deep reactive ion and inductively coupled plasma etching), and metal evaporation. The devices were fabricated on SOI substrates with different buried oxide thicknesses (i.e. 5 µm and 10 µm) and different metals for the trap electrodes (i.e. gold and aluminium). An extremely high-breakdown voltage up to 1 kV was measured in vacuum for the SOI-built test devices with a 10 µm-thick buried oxide formed by oxide film-to-oxide film bonding process. This is attributed to the deep V-shaped undercut profile of the buried oxide layer which resulted in a large breakdown path length, and so mitigating surface breakdown effects. Owing to the V-shaped undercut profile, the surface breakdown voltage was improved by 15% for the devices fabricated on SOI substrates with a 10 µm-thick buried oxide. In the first experiment, the demonstration of ytterbium (174Yb+) ion trapping in the 2D hexagonal lattice trap is achieved with a relatively long lifetime of a laser-cooled ion up to 90 minutes and ≤ 5 minutes without cooling in ultra-high vacuum system. The 2D lattice trap design allows for reliable trapping of 2D ion lattices, rudimentary shuttling between lattice sites and deterministic introducing of defects into the ion lattice. Based on all these abilities, such a 2D lattice trap with the predicted reduction of lattice spacing down to 32 µm can be configured as a versatile architecture for 2D quantum simulations with trapped ions. In the second experiment, microparticle trapping in the 2D lattice trap, performed in air, is achieved with the longest trapping lifetime of 60 minutes. Both gold and aluminium-coated electrodes also lead to comparable trapping performances. Furthermore, the in situ levitation of microparticles is successfully demonstrated at the maximum levitation height of 30 µm. This ability provides additional control on the trapping height which increases the overall functionality of the 2D lattice trap.
Trapped ions in linear Paul traps are largely isolated from interaction with the environment. This property of trapped ions make them a primary choice for quantum technology. \nOver the last decade, trapped atomic ions in linear radio frequency Paul traps have shown to be an important tool to implement quantum algorithms. The scalability of linear ion \ntraps is required to handle large numbers of qubits, in order to implement useful quantum computation. Advance micro-fabrication technology allows the realisation of scalable ion traps. Further developments of micro-trap designs, for the purpose of scalable quantum technology, requires inter-disciplinary investigations of ion traps. Micro-scale ion trap designs typically require a versatile experimental setup. The first part of this thesis describes such an experimental setup including a chip bracket that can host macroscopic ion traps as well as advanced symmetric and asymmetric ion trap chips with up to 90 control electrodes. The system provides versatile optical access for both type of traps and the vacuum chamber is designed in a way so the ion traps can be replaced within a short amount of time. To test the working of the setup, a macroscopic ion trap with an ion-electrode distance of 310±10 μm is used to trap ytterbium ions (Yb+). The trap is characterised by measuring the heating rate, (n•), and spectral noise density SE(ω). A \nphotoionisation technique is used to ionise the different isotopes of Yb in our trap. Isotope selective photoionisation requires exact measurements of 1So↔1P1 transition for the different Yb isotopes. A technique to measure these resonant frequencies is described. \nThis technique works by observing and aligning fluorescence spots and by using this technique, the 1So↔1P1 transition frequencies for stable isotopes of Yb were measured with an accuracy of 60 MHz. These new measured transition frequencies for stable Yb isotopes differ from previously published work by 660 MHz. Furthermore, this technique can also be used to obtain the transition frequencies at different laser-atomic beam angles, typical for non-perpendicular laser-atomic beam angles. The second part of this thesis discusses the optimisation of surface trap geometries as they are being used to implement scalable ion trap designs which consist of a large number of trapping zones. The trap depth in surface traps is low compared to symmetric traps of similar dimensions. How to optimise the trap geometry to achieve maximum trap depth for a given ion height above the trap electrodes, is discussed. Fast and adiabatic ion shuttling operations in one dimension as well as ion separation and recombination processes are important for many quantum information implementations. The maximum speed of separation of trapped ions for adiabatic shuttling operations depends on the secular frequencies, the trapped ion experiences in the process. It will be shown how such ion trap structures have to be designed for fast ion separation process and linear shuttling. Numerical results of adiabatic shuttling operations for trapped ions in such trap structures are also presented.
Ions trapped in Paul traps provide a system which has been shown to exhibit most of the properties required to implement quantum information processing. In particular, a two-dimensional array of ions has been shown to be a candidate for the implementation of quantum simulations. Microfabricated surface geometries provide a widely used technology with which to create structures capable of trapping the required two-dimensional array of ions. To provide a system which can utilise the properties of trapped ions a greater understanding of the surface geometries which can trap ions in two-dimensional arrays would be advantageous, and allow quantum simulators to be fabricated and tested. In this thesis I will present the design, set-up and implementation of an experimental apparatus which can be used to trap ions in a variety of different traps. Particular focus will be put on the ability to apply radio-frequency voltages to these traps via helical resonators with high quality factors. A detailed design guide will be presented for the construction and operation of such a device at a desired resonant frequency whilst maximising the quality factor for a set of experimental constraints. Devices of this nature will provide greater filtering of noise on the rf voltages used to create the electric field which traps the ions which could lead to reduced heating in trapped ions. The ability to apply higher voltages with these devices could also provide deeper traps, longer ion lifetimes and more efficient cooling of trapped ions. In order to efficiently cool trapped ions certain transitions must be known to a required accuracy. In this thesis the 2S1/2 ? 2P1/2 Doppler cooling and 2D3/2 ? 2D[3/2]1/2 repumping transition wavelengths are presented with a greater accuracy then previous work. These transitions are given for the 170, 171, 172, 174 and 176 isotopes of Yb+. Two-dimensional arrays of ions trapped above a microfabricated surface geometry provide a technology which could enable quantum simulations to be performed allowing solutions to problems currently unobtainable with classical simulation. However, the spin-spin interactions used in the simulations between neighbouring ions are required to occur on a faster time-scale than any decoherence in the system. The time-scales of both the ion-ion interactions and decoherence are determined by the properties of the electric field formed by the surface geometry. This thesis will show how geometry variables can be used to optimise the ratio between the decoherence time and the interaction time whilst simultaneously maximising the homogeneity of the array properties. In particular, it will be shown how the edges of the geometry can be varied to provide the maximum homogeneity in the array and how the radii and separation of polygons comprising the surface geometry vary as a function of array size for optimised arrays. Estimates of the power dissipation in these geometries will be given based on a simple microfabrication.
Over the past 15 years ion traps have demonstrated all the building blocks required of a quantum computer. Despite this success, trapping ions remains a challenging task, with the requirement for extensive laser systems and vacuum systems to perform operations on only a handful of qubits. To scale these proof of principle experiments into something that can outperform a classical computer requires an advancement in the trap technologies that will allow multiple trapping zones, junctions and utilize scalable fabrication technologies. I will discuss the construction of an ion trapping experiment, focussing on my work towards the laser stabilization and ion trap design but also covering the experimental setup as a whole. The vacuum system that I designed allows the mounting and testing of a variety of ion trap chips, with versatile optical access and a fast turn around time. I will also present the design and fabrication of a microfabricated Y junction and a 2- dimensional ion trap lattice. I achieve a suppression of barrier height and small variation of secular frequency through the Y junction, aiding to the junctions applicability to adiabatic shuttling operations. I also report the design and fabrication of a 2-D ion trap lattice. Such structures have been proposed as a means to implement quantum simulators and to my knowledge is the first microfabricated lattice trap. Electrical testing of the trap structures was undertaken to investigate the breakdown voltage of microfabricated structures with both static and radio frequency voltages. The results from these tests negate the concern over reduced rf voltage breakdown and in fact demonstrates breakdown voltages significantly above that typically required for ion trapping. This may allow ion traps to be designed to operate with higher voltages and greater ion-electrode separations, reducing anomalous heating. Lastly I present my work towards the implementation of magnetic fields gradients and microwaves on chip. This may allow coupling of the ions internal state to its motion using microwaves, thus reducing the requirements for the use of laser systems.
Microfabricated ion traps are an important tool in the development of scalable quantum systems. Tremendous advancements towards an ion quantum computer were made in the past decade and most requirements for a quantum computer have been fulfilled in individual experiments. Incorporating all essential capabilities in a fully scalable system will require the further advancement of established quantum information technologies and development of new trap fabrication techniques. In my thesis I will discuss the theoretical background and experimental setup required for the operation of ion traps. Measurement of the important ion trap heating rate was performed in the setup and I will discuss the results in more detail. I will give a review of microfabrication processes used for the fabrication of traps, outlining advantages, disadvantages and issues inherent to the processes. Following the review I will present my work on a concept for a scalable ion trap quantum system based on microwave quantum gates and shuttling through X-junctions. Many of the required building blocks, including ion trap structures with current-carrying wires intended to create strong magnetic field gradients for microwave gates were investigated further. A novel fabrication process was developed to combine current-carrying wires with advanced multilayered ion trap structures. Several trap designs intended for proof of principle experiments of high fidelity microwave gates, advanced detection techniques and shuttling between electrically disconnected ion traps will be presented. Also the electrode geometry of an optimized X-junction design with strongly suppressed rf barrier height will be presented. Further, I developed several modifications for the experimental setup to extend the existing capabilities. A plasma source capable of performing in-situ cleans of the trap electrode surfaces, which has been demonstrated to dramatically reduce the heating rate in ion traps, was incorporated. I will also present a vacuum system modification designed to cool ion traps with current-carrying wires and transport the generated heat out of the vacuum system. In addition a novel low-noise, high-speed, multichannel voltage control system was developed by me. The device can be used in future experiments to precisely shuttle ions from one trapping zone to another and also to shuttle ions through ion trap junctions. Lastly I will outline the process optimization and microfabrication of my ion trap designs. A novel fabrication process which makes use of the extremely high thermal conductivity of diamond substrates and combines it with thick copper tracks embedded in the substrate was developed. Large currents will be passed through the wires creating a strong and controllable magnetic field gradient. Ion trap designs with isolated electrodes connected via buried wires can be placed on top of the current-carrying wires, allowing the most advanced electrode designs to be fabricated with current-carrying wires.
The major challenges in trapped-ion quantum computation are to scale up few-ion experiments to many qubits and to improve control techniques so that quantum logic gates can be carried out with higher fidelities. This thesis reports experimental progress in both of these areas. In the early part of the thesis we describe the fabrication of a surface-electrode ion trap, the development of the apparatus and techniques required to operate it and the successful trapping of 40Ca+ ions. Notably we developed methods to control the orientation of the principal axes and to minimise ion micromotion. We propose a repumping scheme that simplifies heating rate measurements for ions with low-lying D levels, and use it to characterise the electric field noise in the trap. Surface-electrode traps are important because they offer a route to dense integration of electronic and optical control elements using existing microfabrication technology. We explore this scaling route by testing a series of three traps that were microfabricated at Sandia National Laboratories. Investigations of micromotion and charging of the surface by laser beams were carried out and improvements to future traps are suggested. Using one of these traps we also investigated anomalous electrical noise from the electrode surfaces and discovered that it can be reduced by cleaning with a pulsed laser. A factor of two decrease was observed; this represents the first in situ removal of this noise source, an important step towards higher gate fidelities. In the second half of the thesis we describe the design and construction of an experiment for the purpose of replacing laser-driven multi-qubit quantum logic gates with microwave-driven ones. We investigate magnetic-field-independent hyperfine qubits in 40Ca+ as suitable qubits for this scheme. We make a design study of how best to integrate an ion trap with the microwave conductors required to implement the gate and propose a novel integrated resonant structure. The trap was fabricated and ions were successfully loaded. Single-qubit experiments show that the microwave fields above the trap are in excellent agreement with software simulations. There are good prospects for demonstrating a multi-qubit gate in the near future. We conclude by discussing the possibilities for larger-scale quantum computation by combining microfabricated traps and microwave control.