Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2610.21435

Accurate gap control of 3D-integrated superconducting quantum circuits using asymmetric indium architecture and multi-angle flip-chip bonding

L. Richard, N. Bruckmoser, J. Feigl, D. Bunch, A. Bhattacharjee, L. Koch, I. Tsitsilin, V. P. Bader, H. Hu, L. Södergren, S. Filipp

quant-phSubmitted Oct 15, 2026• Announced Oct 16, 2026• 0 citations
v1 · Oct 15, 2026v2 · Oct 16, 2026
arXivHTMLPDF

Abstract

Flip-chip 3D integration is a key enabling technology for overcoming the routing and layout constraints of planar superconducting quantum processors, but it requires accurate and uniform control of the inter-chip spacing while preserving qubit coherence. In conventional processes, thick indium bumps are deposited symmetrically on both chips, while dedicated spacers are introduced to limit the residual tilt. Here, we present a flip-chip bonding process based on an asymmetric indium architecture, combining $20\,μ\mathrm{m}$ thick indium bumps on the control chip with $200\,\mathrm{nm}$ thin indium pads on the qubit chip. Using electrical and microwave measurements, we demonstrate low resistance and low loss indium interconnects, and show that transmon qubits integrated with this process reach relaxation and coherence times of $T_1=(159\pm14)\,μ\mathrm{s}$ and $T_{\mathrm{2,echo}}=(294\pm42)\,μ\mathrm{s}$, respectively, comparable to planar devices. Combined with a multi angle compression procedure that suppresses systematic tilt, this approach reduces the average post bonding tilt to $(20\pm12)\,μ\mathrm{rad}$. These results establish an asymmetric indium architecture combined with multi angle compression as a robust, coherence preserving route toward 3D integrated superconducting quantum processors.

Comments
14 pages, 4 main figures, 5 appendix figures

Related papers

Flip-chip integrated superconducting qubits using electroplated bump bonds

Yen-An Shih, Rebecca Gharibaan, Barka Khan +9 more

Flip-chip integration offers a promising route toward scalable superconducting quantum processors and hybrid semiconductor-superconductor quantum devices. We develop a three-dimensional transmon architecture using electroplated indium in which the qubit electric field is shared nearly equally between two bump-bonded substrates while maintaining low participation at the indium-bump interface. The resulting geometry is well suited for future hybrid qubits, enabling the integration of distinct material platforms while minimizing sensitivity to bump-interface loss. Using this platform, we evaluate electroplated indium interconnects for superconducting quantum circuits. Flip-chip transmons incorporating electroplated indium bumps exhibit qubit quality factors around $10^6$. In addition, a systematic study of coplanar-waveguide resonators is used to identify losses associated with the electroplating process. In particular, we find that surface losses associated with the gold-layer, used to enable good electric contact with the indium, is likely the primary contributor to the qubit decay rate. These results demonstrate the compatibility of electroplated indium technology with high-coherence superconducting circuits and establish a promising platform for three-dimensional hybrid quantum integration.

quant-pharXiv:2608.07306•Aug 10, 2026•0 citations

Silicon Hard-Stop Spacers for 3D Integration of Superconducting Qubits

Bethany M. Niedzielski, David K. Kim, Mollie E. Schwartz +9 more

As designs for superconducting qubits become more complex, 3D integration of two or more vertically bonded chips will become necessary to enable increased density and connectivity. Precise control of the spacing between these chips is required for accurate prediction of circuit performance. In this paper, we demonstrate an improvement in the planarity of bonded superconducting qubit chips while retaining device performance by utilizing hard-stop silicon spacer posts. These silicon spacers are defined by etching several microns into a silicon substrate and are compatible with 3D-integrated qubit fabrication. This includes fabrication of Josephson junctions, superconducting air-bridge crossovers, underbump metallization and indium bumps. To qualify the integrated process, we demonstrate high-quality factor resonators on the etched surface and measure qubit coherence (T1, T2,echo> 40 μs) in the presence of silicon posts as near as 350 μm to the qubit.

arXiv:1907.12882•Technical digest - International Electron Devices Meeting/Technical digest•Dec 1, 2019•1 citation

Building blocks of a flip-chip integrated superconducting quantum processor

Sandoko Kosen, Hang-Xi Li, Marcus Rommel +24 more

Abstract We have integrated single and coupled superconducting transmon qubits into flip-chip modules. Each module consists of two chips—one quantum chip and one control chip—that are bump-bonded together. We demonstrate time-averaged coherence times exceeding 90 μs, single-qubit gate fidelities exceeding 99.9%, and two-qubit gate fidelities above 98.6%. We also present device design methods and discuss the sensitivity of device parameters to variation in interchip spacing. Notably, the additional flip-chip fabrication steps do not degrade the qubit performance compared to our baseline state-of-the-art in single-chip, planar circuits. This integration technique can be extended to the realisation of quantum processors accommodating hundreds of qubits in one module as it offers adequate input/output wiring access to all qubits and couplers.

arXiv:2112.02717•Quantum Science and Technology•May 25, 2022•88 citations

Microelectronic Packaging Challenges for Stacked Superconducting Qubit Chips Using Indium Bump Bonding

Andreas W. Schneider, Aswathi Koorikkat, Pawala Ariyathilaka +6 more

In recent years the interest in building quantum computers with superconducting qubits has steadily increased. Indium is one of the chosen interconnect materials for bonding qubit microchips with Josephson junctions to microelectronic resonators because indium is superconducting and ductile. Indium bump bonding is a common technique for hybridizing pixel radiation sensors to readout chips for some time; however, such detectors operate usually at room temperature. The challenge is to transfer this bonding technique to the fabrication of devices that can operate and withstand very low mKtemperatures. This paper summarizes the current challenges for implementing indium bump bonding to stacked superconducting qubit chips with a particular focus on chip parallelism and superconductivity of the interconnects. A high precision of parallelism between bonded qubit and resonator microchips is essential for minimizing signal loss, and superconducting materials such as indium are required for signal transfer. Photolithography or shadow masking techniques are commonly used to deposit several$\mu$m-thick indium bumps on microchips. This paper outlines initial experiments to verify and optimize the indium bump deposition and flip-chip bonding for superconducting qubit chips. Stacked chip parallelism is evaluated after flip-chip bonding, the tolerance of the parallelism between stacked chips will be determined with an optical scanner, microscope and Scanning Electron Microscopy (SEM). For the superconductivity of interconnects, daisy chain chips are designed, built and flip-chip bonded. The common Under-Bump Metallization (UBM) for the adhesion of indium bumps to pixel pads requires modification with superconductive material and is investigated with resistance measurements that are taken at room temperature with a probe tester and at mK-temperature in a helium dilution refrigerator.

European Microelectronics and Packaging Conference•Sep 15, 2025•0 citations

Cryogenic Qubit Integration for Quantum Computing

Rabindra Nath Das, William D. Oliver, Jonilyn Yoder +7 more

We have demonstrated superconducting interconnect technologies that enable a variety of flip-chip 3D integrated structures and packages compatible with high-coherence superconducting qubits. Superconducting indium micro-bumps and underbump metal (UBM) were used to join superconducting qubit chips to superconducting readout and control modules while maintaining high qubit coherence (T1, T2,echo> 20 μs) in the presence of capacitive and inductive coupling between the chips. Scanning electron microscope, X-ray, infrared and confocal microscopy were used to investigate the micro-structure, alignment accuracy, and parallelism of flip-chip qubits. The superconducting readout and control modules can accommodate both niobium and aluminum-based circuit and amplifier fabrication processes, including shadow-evaporated aluminum or Nb/Al-AlOx/Nb trilayer Josephson junctions (JJs). We present results for up to 16 active superconducting chips having trilayer junctions bonded to a passive superconducting module. The I-V characteristics and switching behavior were measured for flip-chip-connected JJ arrays with 40-20,000 JJs. Our approach maintained chip-level junction critical current and qubit coherence, demonstrating it to be a viable approach to building larger quantum computing systems. This paper also discusses packaging approaches to developing a quantum-to-classical interface in a cryogenic environment with multiple temperature stages.

IEEE Electronic Components and Technology Conference (ECTC)•May 1, 2018•47 citations

Silicon Hard-Stop Spacers for 3D Integration of Superconducting Qubits

© 2019 IEEE. As designs for superconducting qubits become more complex, 3D integration of two or more vertically bonded chips will become necessary to enable increased density and connectivity. Precise control of the spacing between these chips is required for accurate prediction of circuit performance. In this paper, we demonstrate an improvement in the planarity of bonded superconducting qubit chips while retaining device performance by utilizing hard-stop silicon spacer posts. These silicon spacers are defined by etching several microns into a silicon substrate and are compatible with 3D-integrated qubit fabrication. This includes fabrication of Josephson junctions, superconducting air-bridge crossovers, underbump metallization and indium bumps. To qualify the integrated process, we demonstrate high-quality factor resonators on the etched surface and measure qubit coherence (T1, T2,echo > 40 μs) in the presence of silicon posts as near as 350 μm to the qubit.

•Dec 1, 2019•8 citations
Flip-chip 3D integration is a key enabling technology for overcoming the routing and layout constraints of planar superconducting quantum processors, but it requires accurate and uniform control of the inter-chip spacing while preserving qubit coherence. In conventional processes, thick indium bumps are deposited symmetrically on both chips, while dedicated spacers are introduced to limit the residual tilt. Here, we present a flip-chip bonding process based on an asymmetric indium architecture, combining 20 μm20\,μ\mathrm{m}20μm thick indium bumps on the control chip with 200 nm200\,\mathrm{nm}200nm thin indium pads on the qubit chip. Using electrical and microwave measurements, we demonstrate low resistance and low loss indium interconnects, and show that transmon qubits integrated with this process reach relaxation and coherence times of T1=(159±14) μsT_1=(159\pm14)\,μ\mathrm{s}T1​=(159±14)μs and T2,echo=(294±42) μsT_{\mathrm{2,echo}}=(294\pm42)\,μ\mathrm{s}T2,echo​=(294±42)μs, respectively, comparable to planar devices. Combined with a multi angle compression procedure that suppresses systematic tilt, this approach reduces the average post bonding tilt to (20±12) μrad(20\pm12)\,μ\mathrm{rad}(20±12)μrad. These results establish an asymmetric indium architecture combined with multi angle compression as a robust, coherence preserving route toward 3D integrated superconducting quantum processors.
Flip-chip integration offers a promising route toward scalable superconducting quantum processors and hybrid semiconductor-superconductor quantum devices. We develop a three-dimensional transmon architecture using electroplated indium in which the qubit electric field is shared nearly equally between two bump-bonded substrates while maintaining low participation at the indium-bump interface. The resulting geometry is well suited for future hybrid qubits, enabling the integration of distinct material platforms while minimizing sensitivity to bump-interface loss. Using this platform, we evaluate electroplated indium interconnects for superconducting quantum circuits. Flip-chip transmons incorporating electroplated indium bumps exhibit qubit quality factors around 10610^6106. In addition, a systematic study of coplanar-waveguide resonators is used to identify losses associated with the electroplating process. In particular, we find that surface losses associated with the gold-layer, used to enable good electric contact with the indium, is likely the primary contributor to the qubit decay rate. These results demonstrate the compatibility of electroplated indium technology with high-coherence superconducting circuits and establish a promising platform for three-dimensional hybrid quantum integration.
As designs for superconducting qubits become more complex, 3D integration of two or more vertically bonded chips will become necessary to enable increased density and connectivity. Precise control of the spacing between these chips is required for accurate prediction of circuit performance. In this paper, we demonstrate an improvement in the planarity of bonded superconducting qubit chips while retaining device performance by utilizing hard-stop silicon spacer posts. These silicon spacers are defined by etching several microns into a silicon substrate and are compatible with 3D-integrated qubit fabrication. This includes fabrication of Josephson junctions, superconducting air-bridge crossovers, underbump metallization and indium bumps. To qualify the integrated process, we demonstrate high-quality factor resonators on the etched surface and measure qubit coherence (T1, T2,echo> 40 μs) in the presence of silicon posts as near as 350 μm to the qubit.
Abstract We have integrated single and coupled superconducting transmon qubits into flip-chip modules. Each module consists of two chips—one quantum chip and one control chip—that are bump-bonded together. We demonstrate time-averaged coherence times exceeding 90 μs, single-qubit gate fidelities exceeding 99.9%, and two-qubit gate fidelities above 98.6%. We also present device design methods and discuss the sensitivity of device parameters to variation in interchip spacing. Notably, the additional flip-chip fabrication steps do not degrade the qubit performance compared to our baseline state-of-the-art in single-chip, planar circuits. This integration technique can be extended to the realisation of quantum processors accommodating hundreds of qubits in one module as it offers adequate input/output wiring access to all qubits and couplers.
In recent years the interest in building quantum computers with superconducting qubits has steadily increased. Indium is one of the chosen interconnect materials for bonding qubit microchips with Josephson junctions to microelectronic resonators because indium is superconducting and ductile. Indium bump bonding is a common technique for hybridizing pixel radiation sensors to readout chips for some time; however, such detectors operate usually at room temperature. The challenge is to transfer this bonding technique to the fabrication of devices that can operate and withstand very low mKtemperatures. This paper summarizes the current challenges for implementing indium bump bonding to stacked superconducting qubit chips with a particular focus on chip parallelism and superconductivity of the interconnects. A high precision of parallelism between bonded qubit and resonator microchips is essential for minimizing signal loss, and superconducting materials such as indium are required for signal transfer. Photolithography or shadow masking techniques are commonly used to deposit severalμ\muμm-thick indium bumps on microchips. This paper outlines initial experiments to verify and optimize the indium bump deposition and flip-chip bonding for superconducting qubit chips. Stacked chip parallelism is evaluated after flip-chip bonding, the tolerance of the parallelism between stacked chips will be determined with an optical scanner, microscope and Scanning Electron Microscopy (SEM). For the superconductivity of interconnects, daisy chain chips are designed, built and flip-chip bonded. The common Under-Bump Metallization (UBM) for the adhesion of indium bumps to pixel pads requires modification with superconductive material and is investigated with resistance measurements that are taken at room temperature with a probe tester and at mK-temperature in a helium dilution refrigerator.
We have demonstrated superconducting interconnect technologies that enable a variety of flip-chip 3D integrated structures and packages compatible with high-coherence superconducting qubits. Superconducting indium micro-bumps and underbump metal (UBM) were used to join superconducting qubit chips to superconducting readout and control modules while maintaining high qubit coherence (T1, T2,echo> 20 μs) in the presence of capacitive and inductive coupling between the chips. Scanning electron microscope, X-ray, infrared and confocal microscopy were used to investigate the micro-structure, alignment accuracy, and parallelism of flip-chip qubits. The superconducting readout and control modules can accommodate both niobium and aluminum-based circuit and amplifier fabrication processes, including shadow-evaporated aluminum or Nb/Al-AlOx/Nb trilayer Josephson junctions (JJs). We present results for up to 16 active superconducting chips having trilayer junctions bonded to a passive superconducting module. The I-V characteristics and switching behavior were measured for flip-chip-connected JJ arrays with 40-20,000 JJs. Our approach maintained chip-level junction critical current and qubit coherence, demonstrating it to be a viable approach to building larger quantum computing systems. This paper also discusses packaging approaches to developing a quantum-to-classical interface in a cryogenic environment with multiple temperature stages.
© 2019 IEEE. As designs for superconducting qubits become more complex, 3D integration of two or more vertically bonded chips will become necessary to enable increased density and connectivity. Precise control of the spacing between these chips is required for accurate prediction of circuit performance. In this paper, we demonstrate an improvement in the planarity of bonded superconducting qubit chips while retaining device performance by utilizing hard-stop silicon spacer posts. These silicon spacers are defined by etching several microns into a silicon substrate and are compatible with 3D-integrated qubit fabrication. This includes fabrication of Josephson junctions, superconducting air-bridge crossovers, underbump metallization and indium bumps. To qualify the integrated process, we demonstrate high-quality factor resonators on the etched surface and measure qubit coherence (T1, T2,echo > 40 μs) in the presence of silicon posts as near as 350 μm to the qubit.