Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2605.28808

Device-Agnostic Microwave Noise Metrology for Nonlinear Cryogenic Quantum Devices

Andrea Celotto, Alessandro Alocco, Bernardo Galvano, Luca Fasolo, Emanuele Palumbo, Luca Callegaro, Luca Oberto, Patrizia Livreri, Emanuele Enrico

quant-phSubmitted May 27, 2026• Announced May 28, 2026• 0 citations• Revised Jul 30, 2026 (v2)
v1 · May 27, 2026v2 · Jul 30, 2026v3 · Aug 26, 2026
arXivHTMLPDF

Abstract

Microwave devices capable of near-quantum-limited signal processing are essential components in the toolbox of solid-state quantum technologies. The manipulation and readout of single-photon microwave signals through amplifiers, mixers, isolators, etc. must fulfill strict requirements in terms of signal integrity to ensure reliable operation. These active microwave quantum devices operate in complex cryo-electronic setups. This poses challenges to their characterization, since all relevant figures of merit must be expressed at the reference planes of their ports. Even though cryogenic S-parameter calibration is non-trivial, metrological approaches are converging toward rigorous methods. Furthermore, preserving signal integrity must be quantified via absolute noise levels at the ports of the Device Under Test (DUT), requiring an absolute power reference. In this work, we present an in situ noise metrology protocol based on substituting a controllable noise source for the DUT. We motivate this choice by showing that placing the noise source at the DUT input impacts the separability of the calibration from the DUT characteristics. Our proposed architecture combines Planck spectroscopy using a Variable Temperature Stage with Short-Open-Load-Reciprocal scattering-parameter calibration, so that noise and scattering quantities are referred to the same cryogenic reference planes. In this configuration, the readout-chain calibration is separated from the internal dynamics of the DUT. As a demanding use case, we apply the protocol to a Josephson Traveling Wave Parametric Amplifier and extract its gain and input-referred added noise under pump conditions activating multimode nonlinear behavior. This illustrates how our device-agnostic protocol supports portable noise characterization of nonlinear cryogenic microwave devices.

Comments
12 pages, 13 figures

Related papers

In situ calibration of microwave attenuation and gain using a cryogenic on-chip attenuator

Thomas Descamps, Linus Andersson, Vittorio Buccheri +3 more

Accurate in situ calibration of microwave attenuation and amplification-chain noise is essential for superconducting quantum circuits. We demonstrate a compact, self-calibrating cryogenic noise source based on an on-chip chromium attenuator that can be resistively heated with nanowatt-level power and directly integrated into a coaxial microwave line at the mixing-chamber stage. By comparing Johnson-Nyquist noise generated by Joule and microwave heating, measured through the amplification chain, the attenuation of the input line, and hence the gain of the chain, is determined without requiring knowledge of the attenuator temperature. The device exhibits millisecond-scale response times and negligible heating of the cryostat base plate. Using this approach, we determine the gain and added noise of a cryogenic amplification chain over the 4-8 GHz band. Our results provide a simple and accurate method to characterize near-quantum-limited parametric amplifiers used in superconducting-qubit readout.

quant-pharXiv:2602.16889•Feb 20, 2026•0 citations

Cryogenic Characterization of a Superconductor Quantum-Based Microwave Reference Source for Communications and Quantum Information

Alírio Boaventura, Justus A. Brevik, Dylan Forrest Williams +6 more

We are developing a new instrument, the RF Josephson arbitrary waveform synthesizer (RF-JAWS), for communications metrology and quantum information applications. An important aspect of the RF-JAWS design is the accurate and traceable characterization of its superconducting devices. In this article, we present a procedure for characterizing microwave superconducting devices in a cryogenic RF probe station via a vector network analyzer (VNA) calibrated with a custom cryogenic calibration kit colocated with the superconducting device under test (DUT) in the cryogenic environment. By de-embedding lossy and dispersive RF interconnects linking the superconducting DUT to the measurement apparatus at room temperature, we characterize the DUT exactly at the cryogenic on-wafer reference plane. More importantly, we operate our VNA with an external modulated source and our procedure features metrology-grade multiline thru-reflect-line calibration and absolute power and phase corrections, as opposed to the more common relative scattering-parameter correction. In addition, we apply anX-parameter model to account for impedance mismatch in cryogenic Josephson microwave sources. Our techniques are also suitable for cryogenic characterization of microwave superconducting devices for solid-state quantum computers and could help to optimize the quantum-classical interfaces in these systems.

IEEE Transactions on Applied Superconductivity•Oct 13, 2021•8 citations

Traceable In Situ Microwave Power Measurement at the Cryogenic Device Plane in a Dilution Refrigerator

Paolo Panetta, Andrea Celotto, Alessandro Alocco +7 more

Accurate knowledge of the microwave power delivered to a cryogenic device under test (DUT) is essential for the characterization and operation of superconducting quantum circuits. However, this information is difficult to obtain inside dilution refrigerators because of distributed attenuation, impedance mismatch, switch-path repeatability, and temperature-dependent microwave components. This paper presents an in situ measurement method for RF power at the cryogenic device plane. The method uses a custom variable temperature stage (VTS) as a cryogenic thermal-transfer element. The TVS is alternately heated by a four-wire DC heater and by microwave power dissipated in a 20 dB pass-through attenuator. By fitting the thermal transients and comparing the corresponding steady-state temperatures, the absorbed microwave power is inferred from a directly measured DC electrical power through an AC/DC substitution procedure. The finite reflection and transmission of the attenuator are then accounted for by cryogenic two-port scattering-parameter measurements based on a switch-assisted Short--Open--Load--Reciprocal calibration, so that the result is referred to the DUT reference plane. The system is demonstrated in a dilution refrigerator with powers between -43 and -58 dBm at the DUT input plane. The demonstrated relative standard uncertainty ranges from about 2% at -43.9 dBm to about 40% at -57.6 dBm. The proposed approach combines thermal RF power transfer, cryogenic S-parameter correction, and uncertainty evaluation in a measurement architecture compatible with quantum-device experiments, providing a practical route toward traceable microwave-power calibration at millikelvin stages.

physics.ins-detCross-listedarXiv:2607.12751•Jul 15, 2026•0 citations

Low-noise amplifier cryogenic testbed validation in a TaaS (Testing-as-a-Service) framework

Brandon Boiko, Eric Zhang, Doug Jorgesen +3 more

As quantum computers based on superconducting qubit processors scale, cryogenic microwave components in the qubit control and readout chain must be appropriately tested and qualified to ensure consistent and high-fidelity quantum computation. However, the intersection of superconducting cryogenics and microwave electronics is a new domain with limited technical and commercial expertise. In this paper we validate a TaaS (testing-as-a-service) framework using an organizational workgroup model that consists of (1) a commercial Test House, (2) standard temperature Component Manufacturer, (3) Academic Partner, and (4) System Integrator to demonstrate a scalable model for the qualification of cryogenic microwave components. The goal of this model is to secure the supply chain and support the rapid growth of Quantum Computing (QC) technologies. The component test vehicle presented in this paper is a low-noise amplifier (LNA) which is a crucial component in the cryogenic chain to ensure adequate signal-to-noise of the qubit readout. We devise standard test metrics and protocols by which LNA performance is measured, including key parameters such as gain and flatness, reflection and isolation, operating bandwidth, and noise figure. We present details of the cryogenic testbed customized for LNA qualification, outline test methodologies, and present a suite of standard processes that are used to systematize data collation and reporting. The testbed is validated by reproducing parameters of a pre-characterized LNA. Its value is demonstrated by characterizing a proof-of-concept cryogenic LNA prototype. Finally, we describe the extension of our TaaS framework toward testing at scale for various active and passive cryogenic components used in QC.

arXiv:2309.03976•Sep 7, 2023•0 citations

Characterization of Traveling-Wave Josephson Parametric Amplifiers at T = 0.3 K

V. Granata, Guerino Avallone, C. Barone +39 more

The growing interest in quantum technologies, from fundamental physics experiments to quantum computing, demands for extremely performing electronics only adding the minimum amount of noise admitted by quantum mechanics to the input signal (i.e., quantum-limited electronics). Superconducting microwave amplifiers, due to their dissipationless nature, exhibit outstanding performances in terms of noise (quantum limited), and gain. However, bandwidth and saturation power still show space for substantial improvement. Within the DARTWARS11DARTWARS (Detector Array Readout with Traveling Wave AmplifieRS), funded by Italian National Nuclear Institute (INFN), is a quantum technologies project targeted at the development of wideband superconducting amplifiers with noise at the quantum limit and the implementation of a quantum-limited readout in different types of superconducting detectors and qubit.collaboration, we are developing state-of-the-art microwave superconducting amplifiers based on Josephson junction arrays and on distributed kinetic inductance transmission lines. Here we report the realization of a setup for the characterization of the performances of Josephson traveling-wave parametric amplifiers at a temperature of 300 mK. Although in the final experimental setup, these amplifiers will operate at a base temperature of about 20 mK, their characterization at 300 mK allows to evidence the main aspects of their performances, but the ultimate noise level. This represents a quick and relatively inexpensive way to test these superconductive devices that can be of help to improve their design and fabrication.

IEEE Transactions on Applied Superconductivity•Oct 14, 2022•6 citations

Low-noise cryogenic microwave amplifier characterization with a calibrated noise source

M. Malnou, Trevyn F. Q. Larson, John D. Teufel +2 more

Parametric amplifiers have become a workhorse in superconducting quantum computing; however, research and development of these devices has been hampered by inconsistent and, sometimes, misleading noise performance characterization methodologies. The concepts behind noise characterization are deceptively simple, and there are many places where one can make mistakes, either in measurement or in interpretation and analysis. In this article, we cover the basics of noise performance characterization and the special problems it presents in parametric amplifiers with limited power handling capability. We illustrate the issues with three specific examples: a high-electron mobility transistor amplifier, a Josephson traveling-wave parametric amplifier, and a Josephson parametric amplifier. We emphasize the use of a 50-Ω shot noise tunnel junction (SNTJ) as a broadband noise source, demonstrating its utility for cryogenic amplifier amplifications. These practical examples highlight the role of loss as well as the additional parametric amplifier "idler" input mode.

arXiv:2312.14900•Review of Scientific Instruments•Mar 1, 2024•15 citations
Microwave devices capable of near-quantum-limited signal processing are essential components in the toolbox of solid-state quantum technologies. The manipulation and readout of single-photon microwave signals through amplifiers, mixers, isolators, etc. must fulfill strict requirements in terms of signal integrity to ensure reliable operation.
These active microwave quantum devices operate in complex cryo-electronic setups. This poses challenges to their characterization, since all relevant figures of merit must be expressed at the reference planes of their ports. Even though cryogenic S-parameter calibration is non-trivial, metrological approaches are converging toward rigorous methods. Furthermore, preserving signal integrity must be quantified via absolute noise levels at the ports of the Device Under Test (DUT), requiring an absolute power reference.
In this work, we present an in situ noise metrology protocol based on substituting a controllable noise source for the DUT. We motivate this choice by showing that placing the noise source at the DUT input impacts the separability of the calibration from the DUT characteristics.
Our proposed architecture combines Planck spectroscopy using a Variable Temperature Stage with Short-Open-Load-Reciprocal scattering-parameter calibration, so that noise and scattering quantities are referred to the same cryogenic reference planes. In this configuration, the readout-chain calibration is separated from the internal dynamics of the DUT. As a demanding use case, we apply the protocol to a Josephson Traveling Wave Parametric Amplifier and extract its gain and input-referred added noise under pump conditions activating multimode nonlinear behavior. This illustrates how our device-agnostic protocol supports portable noise characterization of nonlinear cryogenic microwave devices.
Accurate in situ calibration of microwave attenuation and amplification-chain noise is essential for superconducting quantum circuits. We demonstrate a compact, self-calibrating cryogenic noise source based on an on-chip chromium attenuator that can be resistively heated with nanowatt-level power and directly integrated into a coaxial microwave line at the mixing-chamber stage. By comparing Johnson-Nyquist noise generated by Joule and microwave heating, measured through the amplification chain, the attenuation of the input line, and hence the gain of the chain, is determined without requiring knowledge of the attenuator temperature. The device exhibits millisecond-scale response times and negligible heating of the cryostat base plate. Using this approach, we determine the gain and added noise of a cryogenic amplification chain over the 4-8 GHz band. Our results provide a simple and accurate method to characterize near-quantum-limited parametric amplifiers used in superconducting-qubit readout.
We are developing a new instrument, the RF Josephson arbitrary waveform synthesizer (RF-JAWS), for communications metrology and quantum information applications. An important aspect of the RF-JAWS design is the accurate and traceable characterization of its superconducting devices. In this article, we present a procedure for characterizing microwave superconducting devices in a cryogenic RF probe station via a vector network analyzer (VNA) calibrated with a custom cryogenic calibration kit colocated with the superconducting device under test (DUT) in the cryogenic environment. By de-embedding lossy and dispersive RF interconnects linking the superconducting DUT to the measurement apparatus at room temperature, we characterize the DUT exactly at the cryogenic on-wafer reference plane. More importantly, we operate our VNA with an external modulated source and our procedure features metrology-grade multiline thru-reflect-line calibration and absolute power and phase corrections, as opposed to the more common relative scattering-parameter correction. In addition, we apply anX-parameter model to account for impedance mismatch in cryogenic Josephson microwave sources. Our techniques are also suitable for cryogenic characterization of microwave superconducting devices for solid-state quantum computers and could help to optimize the quantum-classical interfaces in these systems.
Accurate knowledge of the microwave power delivered to a cryogenic device under test (DUT) is essential for the characterization and operation of superconducting quantum circuits. However, this information is difficult to obtain inside dilution refrigerators because of distributed attenuation, impedance mismatch, switch-path repeatability, and temperature-dependent microwave components. This paper presents an in situ measurement method for RF power at the cryogenic device plane. The method uses a custom variable temperature stage (VTS) as a cryogenic thermal-transfer element. The TVS is alternately heated by a four-wire DC heater and by microwave power dissipated in a 20 dB pass-through attenuator. By fitting the thermal transients and comparing the corresponding steady-state temperatures, the absorbed microwave power is inferred from a directly measured DC electrical power through an AC/DC substitution procedure. The finite reflection and transmission of the attenuator are then accounted for by cryogenic two-port scattering-parameter measurements based on a switch-assisted Short--Open--Load--Reciprocal calibration, so that the result is referred to the DUT reference plane. The system is demonstrated in a dilution refrigerator with powers between -43 and -58 dBm at the DUT input plane. The demonstrated relative standard uncertainty ranges from about 2% at -43.9 dBm to about 40% at -57.6 dBm. The proposed approach combines thermal RF power transfer, cryogenic S-parameter correction, and uncertainty evaluation in a measurement architecture compatible with quantum-device experiments, providing a practical route toward traceable microwave-power calibration at millikelvin stages.
As quantum computers based on superconducting qubit processors scale, cryogenic microwave components in the qubit control and readout chain must be appropriately tested and qualified to ensure consistent and high-fidelity quantum computation. However, the intersection of superconducting cryogenics and microwave electronics is a new domain with limited technical and commercial expertise. In this paper we validate a TaaS (testing-as-a-service) framework using an organizational workgroup model that consists of (1) a commercial Test House, (2) standard temperature Component Manufacturer, (3) Academic Partner, and (4) System Integrator to demonstrate a scalable model for the qualification of cryogenic microwave components. The goal of this model is to secure the supply chain and support the rapid growth of Quantum Computing (QC) technologies. The component test vehicle presented in this paper is a low-noise amplifier (LNA) which is a crucial component in the cryogenic chain to ensure adequate signal-to-noise of the qubit readout. We devise standard test metrics and protocols by which LNA performance is measured, including key parameters such as gain and flatness, reflection and isolation, operating bandwidth, and noise figure. We present details of the cryogenic testbed customized for LNA qualification, outline test methodologies, and present a suite of standard processes that are used to systematize data collation and reporting. The testbed is validated by reproducing parameters of a pre-characterized LNA. Its value is demonstrated by characterizing a proof-of-concept cryogenic LNA prototype. Finally, we describe the extension of our TaaS framework toward testing at scale for various active and passive cryogenic components used in QC.
The growing interest in quantum technologies, from fundamental physics experiments to quantum computing, demands for extremely performing electronics only adding the minimum amount of noise admitted by quantum mechanics to the input signal (i.e., quantum-limited electronics). Superconducting microwave amplifiers, due to their dissipationless nature, exhibit outstanding performances in terms of noise (quantum limited), and gain. However, bandwidth and saturation power still show space for substantial improvement. Within the DARTWARS11DARTWARS (Detector Array Readout with Traveling Wave AmplifieRS), funded by Italian National Nuclear Institute (INFN), is a quantum technologies project targeted at the development of wideband superconducting amplifiers with noise at the quantum limit and the implementation of a quantum-limited readout in different types of superconducting detectors and qubit.collaboration, we are developing state-of-the-art microwave superconducting amplifiers based on Josephson junction arrays and on distributed kinetic inductance transmission lines. Here we report the realization of a setup for the characterization of the performances of Josephson traveling-wave parametric amplifiers at a temperature of 300 mK. Although in the final experimental setup, these amplifiers will operate at a base temperature of about 20 mK, their characterization at 300 mK allows to evidence the main aspects of their performances, but the ultimate noise level. This represents a quick and relatively inexpensive way to test these superconductive devices that can be of help to improve their design and fabrication.
Parametric amplifiers have become a workhorse in superconducting quantum computing; however, research and development of these devices has been hampered by inconsistent and, sometimes, misleading noise performance characterization methodologies. The concepts behind noise characterization are deceptively simple, and there are many places where one can make mistakes, either in measurement or in interpretation and analysis. In this article, we cover the basics of noise performance characterization and the special problems it presents in parametric amplifiers with limited power handling capability. We illustrate the issues with three specific examples: a high-electron mobility transistor amplifier, a Josephson traveling-wave parametric amplifier, and a Josephson parametric amplifier. We emphasize the use of a 50-Ω shot noise tunnel junction (SNTJ) as a broadband noise source, demonstrating its utility for cryogenic amplifier amplifications. These practical examples highlight the role of loss as well as the additional parametric amplifier "idler" input mode.