Tantalum thin films sputtered on unheated silicon substrates are characterized with microwaves at around 10 GHz in a 10 mK environment. We show that the phase of tantalum with a body-centered cubic lattice (α-Ta) can be grown selectively by depositing a niobium buffer layer prior to a tantalum film. The physical properties of the films, such as superconducting transition temperature and crystallinity, change markedly with the addition of the buffer layer. Coplanar waveguide resonators based on the composite film exhibit significantly enhanced internal quality factors compared with a film without the buffer layer. The internal quality factor approaches 2 × 107 at a large-photon-number limit. While the quality factor decreases at the single-photon level owing to two-level system (TLS) loss, we have deduced that one of the causes of TLS loss is the amorphous silicon layer at the film–substrate interface, which originates from the substrate cleaning before the film deposition rather than the film itself. The temperature dependence of the internal quality factors shows a marked rise below 200 mK, suggesting the presence of TLS–TLS interactions. The present low-loss tantalum films can be deposited without substrate heating and thus have various potential applications in superconducting quantum electronics.
Tantalum thin films sputtered on unheated silicon substrates are characterized with microwaves at around 10 GHz in a 10 mK environment. We show that the phase of tantalum with a body-centered cubic lattice (α-Ta) can be grown selectively by depositing a niobium buffer layer prior to a tantalum film. The physical properties of the films, such as superconducting transition temperature and crystallinity, change markedly with the addition of the buffer layer. Coplanar waveguide resonators based on the composite film exhibit significantly enhanced internal quality factors compared with a film without the buffer layer. The internal quality factor approaches 2 × 107 at a large-photon-number limit. While the quality factor decreases at the single-photon level owing to two-level system (TLS) loss, we have deduced that one of the causes of TLS loss is the amorphous silicon layer at the film–substrate interface, which originates from the substrate cleaning before the film deposition rather than the film itself. The temperature dependence of the internal quality factors shows a marked rise below 200 mK, suggesting the presence of TLS–TLS interactions. The present low-loss tantalum films can be deposited without substrate heating and thus have various potential applications in superconducting quantum electronics.
Superconducting qubits are a promising platform for large-scale quantum computing. Besides the Josephson junction, most parts of a superconducting qubit are made of a planar, patterned superconducting thin films. In the past, most qubit architectures have relied on niobium (Nb) as the material of choice for the superconducting layer. However, there is also a variety of alternative materials with potentially less losses, which may thereby result in increased qubit performance. One such material is tantalum (Ta), for which high-performance qubit components have already been demonstrated. In this study, we report the sputter-deposition of Ta thin films directly on heated and unheated silicon (Si) substrates as well as onto different, nanometer-thin seed layers from tantalum nitride (TaN), titanium nitride (TiN) or aluminum nitride (AIN) that were deposited first. The thin films are characterized in terms of surface morphology, crystal structure, phase composition, critical temperature, residual resistance ratio (RRR) and RF-performance. We obtain thin films indicative of pure alpha-Ta for high temperature (600°C) sputtering directly on silicon and for Ta deposited on TaN or TiN seed layers. Coplanar waveguide (CPW) resonator measurements show that the Ta deposited directly on the heated silicon substrate performs best with internal quality factors Qi reaching 1xl06in the single-photon regime, measured at T=100 mK.
Tantalum has been demonstrated as a promising material for superconducting qubits. However, comparatively little attention has been given to its nitrides. Tantalum nitride exhibits a range of stoichiometries, resulting in a variety of material properties, including both superconducting and non-superconducting phases. Owing to this versatility, tantalum nitrides can serve multiple purposes in superconducting qubits: as seed layers for alpha-Ta growth, as a superconducting base material and as a non-superconducting barrier in the Josephson junction. In this study, we explore the performance of superconducting TaN and Ta thin film combinations on silicon substrates in terms of internal quality factor Qi. We find that standalone TaN films exhibit Qi values of about 1.5x10^5 at 100mK in the single-photon regime. Surprisingly, a resonator made from Ta grown on a few-nanometers-thick TaN seed layer yields largely the same performance. However, adding an additional, few-nanometers-thick Ta buffer layer between the Si substrate and this TaN seed layer enhances Qi significantly up to 5.9x10^5. Supporting transmission electron microscopy measurements reveal nitrogen accumulation and structural disorder at the TaN-Si interface, while this interfacial modification is suppressed when the Ta buffer layer is introduced. The observed improvement in resonator performance is consistent with a reduction of interface-related two-level system losses and strongly supports the hypothesis that controlling the substrate-metal interface is pivotal for the performance of superconducting qubit circuitry.
Superconducting coplanar waveguide resonators are essential components in quantum processors, where their internal quality factor (Qi) constrains qubit coherence and readout fidelity. In niobium devices, microwave losses at millikelvin temperatures are strongly influenced by two-level systems (TLS) associated with the complex NbOx surface oxide. To mitigate these losses, we investigate a surface-engineering approach in which Nb films are capped in situ with a thin tantalum layer to suppress Nb2O5 formation and replace the native NbOx interface with a Ta-based oxide.
We fabricate Nb/Ta bilayer and reference Nb resonators on high-resistivity silicon using identical DC sputtering and wet etching conditions, and characterize their performance at millikelvin temperatures. Fresh Ta-encapsulated devices exhibit internal quality factors up to 2.4 x 10^6 in the near-single-photon regime, with power dependence consistent with reduced TLS-related loss at the metal-air interface. A control Nb device fabricated under the same process shows comparatively lower Q_TLS, consistent with the beneficial effect of the Ta capping layer. Furthermore, ageing tests performed on Nb/Ta resonators after six months reveal a moderate reduction in Q_TLS relative to their initial values, yet the performance remains superior to newly fabricated Nb-only devices. These results suggest that thin Ta encapsulation enhances interface quality and contributes to improved temporal stability while remaining compatible with Nb-based fabrication workflows.
Abstract The use of α -tantalum in superconducting circuits has enabled a considerable improvement in the coherence time of transmon qubits. The standard approach to grow α -tantalum thin films on silicon involves heating the substrate, which takes several hours per deposition and prevents the integration of this material with wafers containing temperature-sensitive components. We report a detailed experimental study of an alternative growth method of α -tantalum on silicon, which is achieved at room temperature through the use of a niobium seed layer. Despite a substantially higher density of oxygen-rich grain boundaries in the films sputtered at room temperature, resonators made from these films are found to have state-of-the-art quality factors, comparable to resonators fabricated from tantalum grown at high temperature. This finding challenges previous assumptions about correlations between material properties and microwave loss of superconducting thin films, and opens a new avenue for the integration of tantalum into fabrication flows with limited thermal budget.
Understanding the correlation between material properties and microwave losses in superconducting films is a crucial subject for developing low-loss materials for quantum circuits. We focus on vanadium (V) as a novel material for superconducting quantum devices and discuss loss in V films in relation to their structural properties. Using a sputtering method, we grow four V-film structures on (001)-oriented Si wafers, employing Nb and Ta as the buffer and capping layer materials, respectively: Nb/V/Ta, Nb/V, V/Ta, and V. X-ray diffraction and atomic force microscopy reveal that the V films grown on the Nb buffer layers have higher uniformity of lattice orientation and smaller grain size than that directly grown on the Si wafer. Coplanar waveguide resonators are fabricated from the four V-film structures, and averaged photon number (⟨nph⟩) dependences of internal quality factor (Qint) are obtained by performing microwave measurements. By analyzing the obtained Qint vs ⟨nph⟩, it is found that loss at the V surface is dominated by ⟨nph⟩-independent non-two-level-system (non-TLS) losses, which can be mitigated by introducing the Ta capping layer. Furthermore, the V films on the Nb buffer layers exhibit lower Qint in the ⟨nph⟩ range from 100 to 106 and higher non-TLS loss than that directly grown on Si wafers, even though the former has higher lattice-orientation uniformity than the latter. Origins of these trends might be relevant to V oxides, of which presence at surfaces and grain boundaries in bulk regions in the V resonators is suggested by energy dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy, and/or V hydrides.
Tantalum (Ta) has recently received considerable attention in manufacturing robust superconducting quantum circuits. Ta offers low microwave loss, high kinetic inductance compared to aluminium (Al) and niobium (Nb), and good compatibility with complementary metal-oxide-semiconductor (CMOS) technology, which is essential for quantum computing applications. Here, we demonstrate the fabrication engineering of thickness-dependent high quality factor (high-Q_i) Ta superconducting microwave coplanar waveguide resonators. All films are deposited on high-resistivity silicon substrates at room temperature without additional substrate heating. Before Ta deposition, a niobium (Nb) seed layer is used to ensure a body-centred cubic lattice (α-Ta) formation. We further engineer the kinetic inductance (L_K) resonators by varying Ta film thicknesses. High L_K is a key advantage for applications because it facilitates the realisation of high-impedance, compact quantum circuits with enhanced coupling to qubits. The maximum internal quality factor Q_i of ~ 3.6 * 10^6 is achieved at the high power regime for 100 nm Ta, while the highest kinetic inductance is obtained to be 0.6 pH/sq for the thinnest film, which is 40 nm. This combination of high Q_i and high L_K highlights the potential of Ta microwave circuits for high-fidelity operations of compact quantum circuits.