Electronic systems for qubit control and measurement serve as a bridge between quantum programming language and quantum information processors. With the rapid development of superconducting quantum circuit technology, synchronization in a large-scale system, low-latency execution, and low noise are required for electronic systems. Here, we present a field-programmable gate array (FPGA)-based electronic system with a distributed synchronous clock and trigger architecture. The system supports synchronous control of qubits with jitters of ∼5 ps. We implement a real-time digital signal processing system in the FPGA, enabling precise timing control, arbitrary waveform generation, in-phase and quadrature demodulation for qubit state discrimination, and the generation of real-time qubit-state-dependent trigger signals for feedback/feedforward control. The hardware and firmware low-latency design reduces the feedback/feedforward latency of the electronic system to 125 ns, significantly less than the decoherence times of the qubit. Finally, we demonstrate the functionalities and low-noise performance of this system using a fluxonium quantum processor.
Electronic systems for qubit control and measurement serve as a bridge between quantum programming language and quantum information processors. With the rapid development of superconducting quantum circuit technology, synchronization in a large-scale system, low-latency execution, and low noise are required for electronic systems. Here, we present a field-programmable gate array (FPGA)-based electronic system with a distributed synchronous clock and trigger architecture. The system supports synchronous control of qubits with jitters of ∼5 ps. We implement a real-time digital signal processing system in the FPGA, enabling precise timing control, arbitrary waveform generation, in-phase and quadrature demodulation for qubit state discrimination, and the generation of real-time qubit-state-dependent trigger signals for feedback/feedforward control. The hardware and firmware low-latency design reduces the feedback/feedforward latency of the electronic system to 125 ns, significantly less than the decoherence times of the qubit. Finally, we demonstrate the functionalities and low-noise performance of this system using a fluxonium quantum processor.
Quantum circuits utilizing real time feedback techniques (such as active reset and mid-circuit measurement) are a powerful tool for NISQ-era quantum computing. Such techniques are crucial for implementing error correction protocols, and can reduce the resource requirements of certain quantum algorithms. Realizing these capabilities requires flexible, low-latency classical control. We present the development of an open-source FPGA (field-programmable gate array) based processor for pulse-level qubit control. Our processor is designed primarily as an upgrade to QubiC, an open source qubit control platform, but can also be adapted to other systems. The processor is distributed in nature, with one core per arbitrary waveform generator (AWG); simplifying the design and allowing for straightforward scaling. Each processor core implements an instruction set consisting of timed pulse commands as well as simple arithmetic and branching instructions. Our design also includes interfaces for synchronizing the different cores and requesting/receiving (optionally processed) measurement results. Together, these features will allow a user to program arbitrary control flow within a quantum circuit based on previous measurement results. In this poster, we detail our design along with the expected resource utilization on the Xilinx Virtex 7 FPGA, and present pulse-level simulations of our system in the context of a simple feedback experiment.
We have developed an electronic hardware system for the control and readout of multi-superconducting qubit devices. The hardware system is based on the design ideas of good scalability, high synchronization and low latency. The system, housed inside a VPX-6U chassis, includes multiple arbitrary-waveform generator (AWG) channels, analog-digital-converter (ADC) channels as well as direct current source channels. The system can be used for the control and readout of up to twelve superconducting transmon qubits in one chassis, and control and readout of more and more qubit can be carried out by interconnecting the chassis. By using field programmable gate array (FPGA) processors, the system incorporates three features that are specifically useful for superconducting qubit research. Firstly, qubit signals can be processed using the on-board FPGA after being acquired by ADCs, significantly reducing data processing time and data amount for storage and transmission. Secondly, different output modes, such as direct output and sequential output modes, of AWG can be implemented with pre-encoded FPGA. Thirdly, with data acquisition ADCs and controlAWGs jointly controlled by the same FPGA, the feedback latency can be reduced, and in ourtest a 178.4 ns latency time is realized. This is very useful for future quantum feedback experiments. Finally, we demonstrate the functionality of the system by applying the system to the control and readout of a 10 qubit superconducting quantum processor.
This paper reports the development of a low-latency arbitrary waveform generator (AWG), which is suitable for the control and measurement of superconducting quantum computers. It can generate qubit control signals and measurement signals in real time. Compared with commercial AWG, our AWG has less latency and higher analog bandwidth. Compressing latency can reduce system feedback time, and higher analog bandwidth improves the system's integration by mounting more qubits on the readout line. The AWG integrates four high-speed digital-to-analog converters (DACs), phase-locked loop (PLL) circuits, field-programmable gate arrays (FPGAs), and related circuits into a standard PXI 3U board. The waveform generator module, communication interface module, clock module, and configuration module are realized utilizing the FPGA. The FPGA-based hardware architecture enables AWG to be flexibly configured to meet the various needs of quantum experiments. The four-channel AWG has a 2-GSa/s sampling rate, a 14-bit resolution, and 500 MHz bandwidth. The jitter in the AWG output waveform is approximately 3 ps; the latency of the AWG (the time from the feedback trigger received until a feedback pulse is generated) is approximately 55 ns. These designs form the basis of realizing control system for large-scale quantum computing.
Dynamic quantum computing can support quantum error correction circuits to build a large general-purpose quantum computer, which requires electronic instruments to perform the closed-loop operation of readout, processing, and control within 1% of the qubit coherence time. In this paper, we present low-latency readout electronics for dynamic superconducting quantum computing. The readout electronics use a low-latency analog-to-digital converter to capture analog signals, a field-programmable gate array (FPGA) to process digital signals, and the general I/O resources of the FPGA to forward the readout results. Running an algorithm based on the design of multichannel parallelism and single instruction multiple data on an FPGA, the readout electronics achieve a readout latency of 40 ns from the last sample input to the readout valid output. The feedback data link for cross-instrument communication shows a communication latency of 48 ns when 16 bits of data are transmitted over a 2 m-length cable using a homologous clock to drive the transceiver. With codeword-based triggering mechanisms, readout electronics can be used in dynamic superconducting quantum computing.
Quantum circuits utilizing real time feedback techniques (such as active reset and mid-circuit measurement) are a powerful tool for NISQ-era quantum computing. Such techniques are crucial for implementing error correction protocols, and can reduce the resource requirements of certain quantum algorithms. Realizing these capabilities requires flexible, low-latency classical control. We have developed a custom FPGA-based processor architecture for QubiC, an open source platform for superconducting qubit control. Our architecture is distributed in nature, and consists of a bank of lightweight cores, each configured to control a small (1-3) number of signal generator channels. Each core is capable of executing parameterized control and readout pulses, as well as performing arbitrary control flow based on mid-circuit measurement results. We have also developed a modular compiler stack and domain-specific intermediate representation for programming the processor. Our representation allows users to specify circuits using both gate and pulse-level abstractions, and includes high-level control flow constructs (e.g. if-else blocks and loops). The compiler stack is designed to integrate with quantum software tools and programming languages, such as TrueQ, pyGSTi, and OpenQASM3. In this work, we will detail the design of both the processor and compiler stack, and demonstrate its capabilities with a quantum state teleportation experiment using transmon qubits at the LBNL Advanced Quantum Testbed.
In this paper we present a flexible, high-performance, integrated qubit control system using modular PXIe equipment. To manipulate qubits, a classical control system is required to generate and acquire a mix of baseband, radio frequency, and/or optical signals, with the specific mix different for each qubit technology. Typically, a quantum system requires many of these signals with a high degree of synchronization and phase coherence, and increasingly needs real-time data processing and on-the-fly sequencing capabilities for feedback experiments. The proposed system is scalable to hundreds of channels, all of them being phase coherent and fully time-synchronized.The system includes a programmable real-time sequencer for precise execution timing and decision making; and open FPGA capabilities for custom Digital Signal Processing (DSP) by hardware. Using the latter, we present FPGA IP to generate one-/two-qubit gates efficiently with the AWG, and to analyze high-frequency signals to measure the qubit states in real time on the digitizers. This IP features very low latencies for Quantum Error Correction (QEC) and Frequency Division Multiplexing (FDM) capabilities, among others.