We present an analysis of wave mixing in the recently developed Josephson traveling-wave parametric amplifier (JTWPA). Circuit simulations performed using WRSPICE show the full behavior of the JTWPA, allowing propagation of all tones. The coupled mode equations (CMEs) containing only pump, signal, and idler propagation are shown to be insufficient to completely capture complex mixing behavior in the JTWPA. Extension of the CMEs through additional state vectors in the analytic solutions allows closer agreement with WRSPICE. We consider an ordered framework for the systematic inclusion of extended eigenmodes and make a comparison with WRSPICE at each step. The agreement between the two methods validates both approaches and provides insight into the operation of the JTWPA.
We present an analysis of wave mixing in the recently developed Josephson traveling-wave parametric amplifier (JTWPA). Circuit simulations performed using WRSPICE show the full behavior of the JTWPA, allowing propagation of all tones. The coupled mode equations (CMEs) containing only pump, signal, and idler propagation are shown to be insufficient to completely capture complex mixing behavior in the JTWPA. Extension of the CMEs through additional state vectors in the analytic solutions allows closer agreement with WRSPICE. We consider an ordered framework for the systematic inclusion of extended eigenmodes and make a comparison with WRSPICE at each step. The agreement between the two methods validates both approaches and provides insight into the operation of the JTWPA.
Josephson Traveling Wave Parametric Amplifiers (JTWPAs) are largely exploited in quantum technologies for their broadband and low noise performance in the microwave regime. When one or more microwave tones are applied at the input, such devices show a complex wave-mixing response due to their intrinsic nonlinear nature. Numerical simulations of the JTWPAs nonlinear behaviour provide useful insights not only for the design of such devices, but also for the interpretation and validation of the experimental results. Here we present and discuss a comparative analysis of different open-source tools which can be used for JTWPAs numerical simulations. We focus on two tools for transient simulations, WRSPICE and PSCAN2, and on one tool for direct simulation of the frequency domain behaviour, JosephsonCircuit.jl. We describe the working principle of these three tools and test them considering as a benchmark a JTWPA based on SNAILs (Superconducting Nonlinear Asymmetric Inductive eLement) with realistic experimental parameters. Our results can serve as a guide for numerical simulations of JTWPAs with open-source tools, highlighting advantages and disadvantages depending on the simulation tasks.
The recently proposed Josephson traveling-wave parametric amplifier (JTWPA) based on a ladder transmission line consisting of radio-frequency superconducting quantum interference devices and exploiting three-wave mixing has great potential in achieving both a gain of 20 dB and a flat bandwidth of at least 4 GHz. To realize this concept in practical amplifiers, we model the advanced JTWPA circuit with periodic modulation of the circuit parameters (engineered dispersion loadings), which allow the basic mixing process, i.e., ωs=ωp−ωi, where ωs, ωp, and ωi are the signal, the pump, and the idler frequencies, respectively, and efficiently suppress propagation of unwanted higher tones, including ω2p=2ωp, ωp+s=ωp+ωs, ωp+i=ωp+ωi, etc. The engineered dispersion loadings allow achieving a sufficiently wide 3 dB-bandwidth from 3 to 9 GHz combined with a reasonably small ripple (±2 dB) in the gain-vs-frequency dependence.
The development of large-scale superconducting quantum computers critically depends on the accurate readout of qubit states. To enable this, cryogenic parametric amplifiers have been proposed and developed, and have since found widespread use in small-signal detection applications. Among various amplifier architectures, Josephson traveling-wave parametric amplifiers (JTWPAs) are widely adopted due to their broad bandwidth, high saturation power, and compatibility with superconducting qubits. In this work, we present a design workflow of JTWPAs based on a co-simulation approach combining electromagnetic (EM) and circuit-level simulation. We apply this method to a uniform JTWPA, comparing our simulation results with experimental data. To mitigate the challenge of constructing lumped element circuit models usually used in conventional simulation method, we directly perform full EM analysis of the device to accurately determine its linear response. The extracted S parameters are then fed into a nonlinear harmonic balance simulator with Josephson junctions modeled as circuit elements. By doing so, the linear and gain properties of the JTWPA are extracted. Different factors that impact device performance including gain compression, phase matching, and fabrication imperfections are further investigated and modeled. A good agreement between simulation and measurements is identified, establishing the effectiveness of our approach in designing quantum parametric amplifiers.
Recent advancements in quantum technologies and advanced detection experiments have underscored the pressing need for the detection of exceedingly weak signals within the microwave frequency spectrum. Addressing this challenge, the Josephson Traveling Wave Parametric Amplifier (JTWPA) has been proposed as a cryogenic front-end amplifier capable of approaching the quantum noise limit while providing a relevant bandwidth. This research is centered on a comprehensive numerical investigation of the JTWPA, without resorting to simplifications regarding the nonlinearity of the essential components. Specifically, this study focuses on a thorough examination of the system, characterized by coupled nonlinear differential equations representing all components of the device. Proper input and output signals at the device's boundaries are considered. The analysis of the output signals undergoing the parametric amplification process involves a detailed exploration of phase-space dynamics and Fourier spectral analysis of the output voltage. This study is conducted while considering the parameters ruling the response of the device under pump and signal excitations. In addition to the expected signal amplification, the findings reveal that the nonlinear nature of the system can give rise to unforeseen phenomena, depending on the system's operational conditions, which include: the generation of pump tone harmonics, modulation of the signal gain, and incommensurate frequency generation—effects that are not easily accommodated by simplistic linearized approaches.
In this work, we develop a comprehensive numerical analysis of the dynamic response of a Josephson Traveling Wave Parametric Amplifier (JTWPA) by varying the driving parameters, with a focus on the pathways leading to chaotic behavior. By tuning the working conditions, we capture the broad spectrum of dynamical regimes accessible to JTWPAs, delineating the settings under which transition to chaos occurs. Furthermore, we extend our investigation to device formed by junctions characterized by a non--sinusoidal current phase relation (CPR) and exploring the impact of its shape on the amplifier's performance. Through the study of gain characteristics, Poincaré sections, and Fourier spectra, we provide an in-depth understanding of how non-linearity and CPR nonsinusoidality influence the JTWPAs' operational effectiveness and stability. This investigation offers insights into optimizing the device designs for enhanced performance and robustness against chaotic disruptions, in order to establish a framework for predicting and controlling JTWPA behavior in practical applications. This effort will pave the way for the development of devices with tailored dynamic responses and for advancements in quantum computing and precision measurement technologies, where stability and high fidelity are of paramount importance.
Josephson traveling-wave parametric amplifiers (JTWPAs) are wideband, ultralow-noise amplifiers used to enable the readout of superconducting qubits. While individual JTWPAs have achieved high performance, behavior between devices is inconsistent due to wide manufacturing tolerances. Amplifier designs could be modified to improve resilience towards variations in amplifier components; however, existing device models often rely on analytical techniques that typically fail to incorporate component variations. To begin addressing this issue, a 1D numerical method for modeling JTWPAs is introduced in this work. The method treats the Josephson junctions and transmission lines in an amplifier as coupled subsystems and can easily incorporate arbitrary parameter variations. We discretize the transmission line subsystem with a finite element time domain method and the Josephson junction subsystem with a finite difference method, with leap-frog time marching used to evolve the system in time. We validate our method by comparing the computed gain to an analytical model for a traditional JTWPA architecture and one with resonant phase matching. We then use our method to demonstrate the impact of variations in Josephson junctions and phase-matching resonators on amplification. In future work, the method will be adjusted to incorporate additional amplifier architectures and extended to a 3D full-wave approach.