Josephson traveling-wave parametric amplifiers (JTWPAs) are wideband, ultralow-noise amplifiers used to enable the readout of superconducting qubits. While individual JTWPAs have achieved high performance, behavior between devices is inconsistent due to wide manufacturing tolerances. Amplifier designs could be modified to improve resilience towards variations in amplifier components; however, existing device models often rely on analytical techniques that typically fail to incorporate component variations. To begin addressing this issue, a 1D numerical method for modeling JTWPAs is introduced in this work. The method treats the Josephson junctions and transmission lines in an amplifier as coupled subsystems and can easily incorporate arbitrary parameter variations. We discretize the transmission line subsystem with a finite element time domain method and the Josephson junction subsystem with a finite difference method, with leap-frog time marching used to evolve the system in time. We validate our method by comparing the computed gain to an analytical model for a traditional JTWPA architecture and one with resonant phase matching. We then use our method to demonstrate the impact of variations in Josephson junctions and phase-matching resonators on amplification. In future work, the method will be adjusted to incorporate additional amplifier architectures and extended to a 3D full-wave approach.
Josephson traveling-wave parametric amplifiers (JTWPAs) are wideband, ultralow-noise amplifiers used to enable the readout of superconducting qubits. While individual JTWPAs have achieved high performance, behavior between devices is inconsistent due to wide manufacturing tolerances. Amplifier designs could be modified to improve resilience towards variations in amplifier components; however, existing device models often rely on analytical techniques that typically fail to incorporate component variations. To begin addressing this issue, a 1D numerical method for modeling JTWPAs is introduced in this work. The method treats the Josephson junctions and transmission lines in an amplifier as coupled subsystems and can easily incorporate arbitrary parameter variations. We discretize the transmission line subsystem with a finite element time domain method and the Josephson junction subsystem with a finite difference method, with leap-frog time marching used to evolve the system in time. We validate our method by comparing the computed gain to an analytical model for a traditional JTWPA architecture and one with resonant phase matching. We then use our method to demonstrate the impact of variations in Josephson junctions and phase-matching resonators on amplification. In future work, the method will be adjusted to incorporate additional amplifier architectures and extended to a 3D full-wave approach.
Josephson traveling wave parametric amplifiers are a leading tool for enabling readout of superconducting qubits. However, existing design tools for these devices struggle to effectively model variations in amplifier parameters, leading to inconsistencies between theoretical predictions and manufactured devices. This work develops a 1D hybrid numerical modeling approach for these devices that can easily incorporate amplifier property variations, allowing their impact to be considered in the design process. Here, the formulation of the method is introduced and validated against analytical results for a simple architecture. Future work will extend the technique to more advanced amplifier architectures, as well as develop similar methods for 3D full-wave modeling of these systems.
The development of large-scale superconducting quantum computers critically depends on the accurate readout of qubit states. To enable this, cryogenic parametric amplifiers have been proposed and developed, and have since found widespread use in small-signal detection applications. Among various amplifier architectures, Josephson traveling-wave parametric amplifiers (JTWPAs) are widely adopted due to their broad bandwidth, high saturation power, and compatibility with superconducting qubits. In this work, we present a design workflow of JTWPAs based on a co-simulation approach combining electromagnetic (EM) and circuit-level simulation. We apply this method to a uniform JTWPA, comparing our simulation results with experimental data. To mitigate the challenge of constructing lumped element circuit models usually used in conventional simulation method, we directly perform full EM analysis of the device to accurately determine its linear response. The extracted S parameters are then fed into a nonlinear harmonic balance simulator with Josephson junctions modeled as circuit elements. By doing so, the linear and gain properties of the JTWPA are extracted. Different factors that impact device performance including gain compression, phase matching, and fabrication imperfections are further investigated and modeled. A good agreement between simulation and measurements is identified, establishing the effectiveness of our approach in designing quantum parametric amplifiers.
Josephson traveling-wave parametric amplifiers (JTWPAs) are critical for superconducting quantum computers in enabling simultaneous high-fidelity measurements of many qubits. Despite their importance, translating designs to working hardware remains a significant obstacle, with numerical modeling increasingly being used to help close this gap. Unfortunately, existing time-domain (TD) circuit modeling methods struggle to close this gap due to their inability to model the physical layout of a device. In principle, finite-element time-domain (FETD) methods can model the JTWPA physical layout, but these simulations are complicated by the wide bandwidths and multiscale features involved. Here, we develop an unconditionally stable 1-D FETD model for JTWPAs that can model dispersive losses over wide bandwidths to begin overcoming these challenges. We validate our method against harmonic balance (HB) simulations of a Floquet-mode JTWPA before simulating a realistic multiplexed qubit readout scenario where HB is impractical.
Josephson junction based parametric amplifiers are used to read out the state of superconducting qubits with high fidelity. These amplifiers are themselves superconducting circuits operating at temperatures of tens of millikelvin. A version of this type of amplifier which has exhibited large bandwidth and saturation power is the Josephson traveling wave parametric amplifier (JTWPA). One particular JTWPA topology consists of hundreds to thousands of Josephson junctions in a transmission line configuration along with periodic phase matching resonators to increase gain. Here, we look at using a superconducting qubit fabrication process to realize this circuit To analyze the sensitivity of the JTWPA to fabrication process variation, we discuss a linear model for the circuit which takes into account unit cell to unit cell variation. To extract the measured circuit values, we use in-situ measurements of a JTWPA to compare the designed values to the realized values. Finally we discuss preliminary results realizing an example JTWPA design using a fabrication process designed for superconducting qubits.
This work presents the design, fabrication strategy, and numerical modeling of niobium-based Josephson traveling-wave parametric amplifiers (JTWPAs) for quantum microwave readout. These devices are designed as nonlinear transmission lines composed of more than two thousand Josephson junction unit cells, with periodically embedded resonators enabling phase matching. The use of Nb trilayer technology (Nb/AlO[Formula: see text]/Nb) with respect to Al-based devices ensures higher junction uniformity, lower losses, and higher resilience to stray magnetic fields. We developed a multi-scale modeling framework combining harmonic balance methods and time-domain simulations of nonlinear coupled differential equations to describe wave propagation, parametric amplification, and spectral dynamics. Numerical results predict broadband gain up to 20[Formula: see text]dB over multi-GHz bandwidths. These results demonstrate the potential of Nb-based JTWPAs as scalable components for quantum applications.
Recent progress in physics has increased the necessity for ultra-low noise amplifiers capable of operating at the quantum limit performance. These amplifiers are essential to enhance astronomical detection, dark-matter search, and qubit readout in quantum computing, among other applications. Superconducting Josephson junction Travelling Wave Parametric Amplifiers (JTWPAs) operated in the microwave range, have demonstrated high gain over several gigahertz (GHz) bandwidth, with quantum-limited noise performance and minimal heat dissipation. These excellent properties make JTWPAs an ideal solution for ultra-low noise amplification. This thesis delves into the design, fabrication and characterisation of JTWPAs operated in the microwave (1-16 GHz) and the W-band (70-115GHz) regimes. A generalised coupled-mode equations (CME) framework describing JTWPAs based on Josephson junctions and DC superconducting quantum interference devices (SQUIDs) is introduced. This framework can be combined with electromagnetic (EM) simulation softwares to model the JTWPAs, facilitating their design. It is therefore used to model two microwave JTWPA designs, using parallel plate capacitors (PPCs) and interdigitated capacitors (IDCs). The fabrication and characterisation of both designs are presented, and possible fabrication and design issues are carefully discussed. Despite these issues, we observed broadband gain in the JTWPA with PPCs, achieving > 20 dB gain at several frequency points, and a measured P1dB = −95.8dBm when operated at 17.3 dB. The RF properties of a 500-junction Josephson array are also presented in this manuscript. The device creates a Fabry-Perot cavity, leading to non-travelling wave parametric effects, such as narrow-band gain. We also observed indications of efficient phase-sensitive amplification. The thesis is concluded with the first — to the best of our knowledge — experimental attempt to extend the operational frequency of a JTWPA to the W-band. The novel design, fabrication techniques and characterisation of the W-band JTWPA are discussed in detail in this manuscript, leading to promising results suggesting that JTWPA could operate at high frequencies.