Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:0705.4140 · Applied Physics Letters

Mg B 2 radio-frequency superconducting quantum interference device prepared by atomic force microscope lithography

M. Gregor, T. Pleceník, M. Praščák, R. Mičunek, M. Kubinec, Vladimír Gašparík, M. Grajcar, Peter Kúš, Andrej Plecenik

Published Sep 17, 2007• 6 citations
arXivHTMLPDF

Abstract

A new method of preparation of radio-frequency superconducting quantum interference devices on MgB2 thin films is presented. The variable-thickness bridge was prepared by a combination of optical lithography and of the scratching by an atomic force microscope. The critical current of the nanobridge was 0.35μA at 4.2K. Noncontact measurements of the current-phase characteristics and of the critical current versus temperature have been investigated on the authors’ structures.

DOI
10.1063/1.2779095

Related papers

RF-SQUID prepared on MgB2 variable-thickness bridge by AFM scratching

M. Gregor, T. Pleceník, M. Praščák +6 more

We present the preparation of radio-frequency superconducting quantum interface devices (SQUID) on MgB2 thin film with Tc=32 K. Variable-thickness bridge was prepared by combination of optical lithography and AFM scratching technique. The critical current of nanobridge was 0.35 uA at 4.2 K. Non-contact measurements of current-phase characteristics and critical current vs. temperature have been investigated on our SQUID structures.

•May 29, 2007•0 citations

Fabrication and Characterization of Miniaturized NbN Superconducting Quantum Interference Devices With Nanobridge Junctions

Hao Wang, Lei Chen, Xiaoyu Liu +4 more

Reduction of the size of the superconducting quantum interference device (SQUID) ring structure improves its sensitivity to magnetic moments. Nanobridge junctions are advantageous for SQUID miniaturization. However, many planar SQUIDs with nanobridge junctions have shallow flux modulation depths because of their nonideal Josephson current-phase relationships. Here, we fabricated a three-dimensional niobium nitride (NbN) miniaturized SQUID in which the nanobridge junction structures are much thinner than the superconducting ring. We grew a thick superconducting NbN film on a silicon wafer and embedded an insulating slit in the middle of the film. By setting two thin nanobridge junctions across this insulating slit, we were able to manufacture NbN miniaturized SQUIDs that, in principle, can become nano-SQUIDs. The flux modulation depths of these devices reached 36% at 4.2 K. In addition, the fabricated devices show reversible current-voltage characteristics in the absence of any shunting resistance.

IEEE Transactions on Applied Superconductivity•Jan 18, 2017•10 citations

Nano-superconducting quantum interference devices with suspended junctions

Dibyendu Hazra, John R. Kirtley, K. Hasselbach

Nano-Superconducting Quantum Interference Devices (nano-SQUIDs) are usually fabricated from a single layer of either Nb or Al. We describe here a simple method for fabricating suspended nano-bridges in Nb/Al thin-film bilayers. We use these suspended bridges, which act as Josephson weak links, to fabricate nano-SQUIDs which show critical current oscillations at temperatures up to 1.5 K and magnetic flux densities up to over 20 mT. These nano-SQUIDs exhibit flux modulation depths intermediate between all-Al and all-Nb devices, with some of the desirable characteristics of both. The suspended geometry is attractive for magnetic single nanoparticle measurements.

Applied Physics Letters•Apr 14, 2014•25 citations

Characteristics of focused ion beam nanoscale Josephson devices

L Hao, David Cox, John C. Gallop

The requirements of quantum metrology and nanoscience are driving the need for single-particle detection capability across a wide variety of physics areas, including quantum information processing, single-photon detection, nanoelectromechanical systems, nanomagnetism and spintronics. The single particles to be detected include atoms, molecules, photons, spins and even phonons, in the future. Nanoscale superconducting quantum interference devices (nanoSQUIDs) represent a new manifestation of an old but exciting superconducting technology which addresses some of these requirements. In this paper we describe a straightforward approach to fabricating Nb microbridge weak links using combined optical lithography and focused ion beams which may be used to fabricate nanoSQUIDs. The devices show non-hysteretic current?voltage characteristics and demonstrate very low noise, even at operating temperatures above 4.2?K. To improve our understanding of the superconducting properties of the Josephson microbridge/nanobridge junctions which have proved very successful in realizing low noise nanoSQUIDs we have carried out a combination of investigations. These include cryogenic resistance versus temperature (R(T)) and current?voltage characteristic measurements, atomic force microscope scans, controlled gallium (Ga) ion milling and implantation, and ion beam track modelling of these Josephson devices and Nb thin films.

Superconductor Science and Technology•May 14, 2009•19 citations

Quantum interference devices made from superconducting oxide thin films

R. H. Koch, Corwin P. Umbach, G. J. Clark +2 more

We have fabricated superconducting quantum interference devices (dc SQUID’s) from thin films of the superconducting oxide YBa2Cu3Oy. The devices were made by first lithographically patterning an ion implant mask containing a 40 by 40 μm loop and two 17-μm-wide weak links over a ∼1-μm-thick oxide film. Ion implantation was then used to destroy the superconductivity in the film surrounding the device without actually removing material, resulting in a completely planar structure for the SQUID’s. The SQUID’s were operated in the temperature range from 4.2 to 68 K. The superconducting flux quantum was measured to be h/2e in these materials.

Applied Physics Letters•Jul 20, 1987•379 citations

Fabrication of Niobium Nanobridge Josephson Junctions

Takashi Tachiki, Kenji Horiguchi, Takashi Uchida

To realize antenna-coupled Josephson detectors for microwave and millimeter-wave radiation, planar-type Nb nanobridge Josephson junctions were fabricated. Nb thin films whose thickness, the root mean square roughness and the critical temperature were 20.0 nm, 0.109 nm and 8.4 K, respectively were deposited using a DC magnetron sputtering at a substrate temperature of 700°C. Nanobridges were obtained from the film using 80-kV electron beam lithography and reactive ion-beam etching in CF 4 (90%) + O2 (10%) gases. The minimum bridge area was 65 nm wide and 60 nm long. For the nanobridge whose width and length were less than 110 nm, an I-V characteristic showed resistively-shunted-junction behaviour near the critical temperature. Moreover, Shapiro steps were observed in the nanobridge with microwave irradiation at a frequency of 6 – 30 GHz. The Nb nanobridges can be used as detectors in the antenna-coupled devices.

Journal of Physics Conference Series•May 12, 2014•1 citation
A new method of preparation of radio-frequency superconducting quantum interference devices on MgB2 thin films is presented. The variable-thickness bridge was prepared by a combination of optical lithography and of the scratching by an atomic force microscope. The critical current of the nanobridge was 0.35μA at 4.2K. Noncontact measurements of the current-phase characteristics and of the critical current versus temperature have been investigated on the authors’ structures.
Reduction of the size of the superconducting quantum interference device (SQUID) ring structure improves its sensitivity to magnetic moments. Nanobridge junctions are advantageous for SQUID miniaturization. However, many planar SQUIDs with nanobridge junctions have shallow flux modulation depths because of their nonideal Josephson current-phase relationships. Here, we fabricated a three-dimensional niobium nitride (NbN) miniaturized SQUID in which the nanobridge junction structures are much thinner than the superconducting ring. We grew a thick superconducting NbN film on a silicon wafer and embedded an insulating slit in the middle of the film. By setting two thin nanobridge junctions across this insulating slit, we were able to manufacture NbN miniaturized SQUIDs that, in principle, can become nano-SQUIDs. The flux modulation depths of these devices reached 36% at 4.2 K. In addition, the fabricated devices show reversible current-voltage characteristics in the absence of any shunting resistance.
Nano-Superconducting Quantum Interference Devices (nano-SQUIDs) are usually fabricated from a single layer of either Nb or Al. We describe here a simple method for fabricating suspended nano-bridges in Nb/Al thin-film bilayers. We use these suspended bridges, which act as Josephson weak links, to fabricate nano-SQUIDs which show critical current oscillations at temperatures up to 1.5 K and magnetic flux densities up to over 20 mT. These nano-SQUIDs exhibit flux modulation depths intermediate between all-Al and all-Nb devices, with some of the desirable characteristics of both. The suspended geometry is attractive for magnetic single nanoparticle measurements.
The requirements of quantum metrology and nanoscience are driving the need for single-particle detection capability across a wide variety of physics areas, including quantum information processing, single-photon detection, nanoelectromechanical systems, nanomagnetism and spintronics. The single particles to be detected include atoms, molecules, photons, spins and even phonons, in the future. Nanoscale superconducting quantum interference devices (nanoSQUIDs) represent a new manifestation of an old but exciting superconducting technology which addresses some of these requirements. In this paper we describe a straightforward approach to fabricating Nb microbridge weak links using combined optical lithography and focused ion beams which may be used to fabricate nanoSQUIDs. The devices show non-hysteretic current?voltage characteristics and demonstrate very low noise, even at operating temperatures above 4.2?K. To improve our understanding of the superconducting properties of the Josephson microbridge/nanobridge junctions which have proved very successful in realizing low noise nanoSQUIDs we have carried out a combination of investigations. These include cryogenic resistance versus temperature (R(T)) and current?voltage characteristic measurements, atomic force microscope scans, controlled gallium (Ga) ion milling and implantation, and ion beam track modelling of these Josephson devices and Nb thin films.
We have fabricated superconducting quantum interference devices (dc SQUID’s) from thin films of the superconducting oxide YBa2Cu3Oy. The devices were made by first lithographically patterning an ion implant mask containing a 40 by 40 μm loop and two 17-μm-wide weak links over a ∼1-μm-thick oxide film. Ion implantation was then used to destroy the superconductivity in the film surrounding the device without actually removing material, resulting in a completely planar structure for the SQUID’s. The SQUID’s were operated in the temperature range from 4.2 to 68 K. The superconducting flux quantum was measured to be h/2e in these materials.
To realize antenna-coupled Josephson detectors for microwave and millimeter-wave radiation, planar-type Nb nanobridge Josephson junctions were fabricated. Nb thin films whose thickness, the root mean square roughness and the critical temperature were 20.0 nm, 0.109 nm and 8.4 K, respectively were deposited using a DC magnetron sputtering at a substrate temperature of 700°C. Nanobridges were obtained from the film using 80-kV electron beam lithography and reactive ion-beam etching in CF 4 (90%) + O2 (10%) gases. The minimum bridge area was 65 nm wide and 60 nm long. For the nanobridge whose width and length were less than 110 nm, an I-V characteristic showed resistively-shunted-junction behaviour near the critical temperature. Moreover, Shapiro steps were observed in the nanobridge with microwave irradiation at a frequency of 6 – 30 GHz. The Nb nanobridges can be used as detectors in the antenna-coupled devices.