Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:physics/0610279 · Review of Scientific Instruments

Microfabricated electromagnetic filters for millikelvin experiments

H. le Sueur, P. Joyez

Published Nov 1, 2006• 29 citations
arXivHTMLPDF

Abstract

In this article we report on the design, fabrication, and tests of microfabricated broadband filters suitable for proper electromagnetic thermalization of electrical lines connected to sensitive quantum electronics experiments performed at dilution fridge temperatures. Compared to previous such miniature filters, the new design improves on performance and reliability. These filters can be packed in space-saving cases with either single or multicontact connector. Measured performance in the accessible range compares well to simulations. We use these simulations to discuss the effectiveness of these filters for electromagnetic thermalization at 30mK.

DOI
10.1063/1.2370744

Related papers

Miniature electrical filters for single electron devices

D. Vion, P.F. Orfila, P. Joyez +2 more

In experiments on single electron devices, the electromagnetic noise from parts of the apparatus at temperatures higher than that of the device can dramatically increase the tunnel rates out of the Coulomb-blocked state and therefore increase the device error rate. The electrical lines must therefore be filtered adequately. We derive simple expressions for calculating the required attenuation coefficient. We describe a wide-band miniature dissipative filter functioning at cryogenic temperatures. The effective thermalization of an experiment at 30 mK can be obtained by placing four of these filters in series at temperatures ranging from 4 K to 30 mK.

Journal of Applied Physics•Mar 15, 1995•93 citations

Note: Cryogenic coaxial microwave filters

Giovanna Tancredi, Simon Schmidlin, P. J. Meeson

The careful filtering of microwave electromagnetic radiation is critical for controlling the electromagnetic environment for experiments in solid-state quantum information processing and quantum metrology at millikelvin temperatures. We describe the design and fabrication of a coaxial filter assembly and demonstrate that its performance is in excellent agreement with theoretical modelling. We further perform an indicative test of the operation of the filters by making current-voltage measurements of small, underdamped Josephson junctions at 15 mK.

arXiv:1308.6716•Review of Scientific Instruments•Feb 1, 2014•9 citations

Improved powder filters for qubit measurements

Alexander V. Lukashenko, Alexey Vladimirovich Ustinov

We designed and fabricated miniature low-pass metal powder filters suitable for noise-sensitive measurements at cryogenic temperatures. In comparison with previous powder filters, our filters have a much better frequency response and significantly smaller dimensions (0.7 cm(3) including the plugs) and can also be used as hermetic feedthroughs at low temperatures. Their transmission characteristics are smooth, contain no ripples, and have a steep decay above the cutoff frequency. At 4.2 K the cutoff frequency of a single filter is f(c)=1 MHz and the roll-off is -50 dB per decade. All of the fabricated filters have identical frequency responses at 4.2 K and their characteristics are reliably reproducible.

Review of Scientific Instruments•Jan 1, 2008•59 citations

Design and Optimization of a Hybrid Design for Quantum Transduction

Enrico Bargagna, Julian Delgado, Changqing Wang +5 more

This study presents the mechanical design and analysis of a quantum electro-optical transducer engineered to operate at millikelvin temperatures within a dilution refrigerator. The transducer enables bidirectional microwave-optical frequency conversion through a hybrid architecture that integrates a superconducting radiofrequency (SRF) cavity with an electro-optic optical cavity. Among several design options investigated, the configuration offering the best thermal and mechanical performance was selected, yielding a robust solution with reduced sensitivity to fabrication tolerances, improved heat dissipation, as well as alignment precision. The design ensures uniform temperature distribution, enabling higher laser pump powers and, thus, increased conversion efficiency, while maintaining mechanical stresses safely below the material yield strength. Electromagnetic simulations further validate the design, demonstrating enhanced coupling between the optical and microwave modes, as well as a broader tuning range achieved with smaller tuner displacements.

Sensors•Oct 15, 2025•1 citation

Millikelvin confocal microscope with free-space access and high-frequency electrical control

Thomas Descamps, Feng Liu, Tobias Hangleiter +3 more

Cryogenic confocal microscopy is a powerful method for studying solid state quantum devices such as single photon sources and optically controlled qubits. While the vast majority of such studies have been conducted at temperatures of a few Kelvin, experiments involving fragile quantum effects often require lower operating temperatures. To also allow for electrical dynamic control, microwave connectivity is required. For polarization-sensitive studies, free space optical access is advantageous compared to fiber coupling. Here we present a confocal microscope in a dilution refrigerator providing all the above features at temperatures below 100 mK. The installed high frequency cabling meets the requirements for state-of-the-art spin qubit experiments. As another unique advantage of our system, the sample fitting inside a large puck can be exchanged while keeping the cryostat cold with minimal realignment. Assessing the performance of the instrument, we demonstrate confocal imaging, sub-nanosecond modulation of the emission wavelength of a suitable sample, and an electron temperature of 76 mK. While the instrument was constructed primarily with the development of optical interfaces to electrically controlled qubits in mind, it can be used for many experiments involving quantum transport, solid state quantum optics, and microwave-optical transducers.

arXiv:2401.03266•Review of Scientific Instruments•Aug 1, 2024•1 citation

Robust cryogenic matched low-pass coaxial filters for quantum computing applications

Аnton I. Ivanov, Victor I. Polozov, Vladimir V. Echeistov +5 more

Electromagnetic noise is one of the main external factors decreasing superconducting qubit coherence. Matched coaxial filters can prevent microwave and IR photons' negative influence on superconducting quantum circuits. In this report, we describe the design and fabrication process of matched coaxial filters for noise-sensitive measurements at millikelvin temperatures. A robust transmission coefficient and ultralow reflection loss of −20 dB in the frequency range up to 20 GHz is achieved. Fabricated low-pass filters have linear transmission and reflection characteristics with 3 dB-cutoff frequency of 1.5–2.5 GHz. A method for extracting the propagation constant and filter impedance from scattering parameter measurements is demonstrated. This method is experimentally approved on a filter with a compound of Cu powder and Stycast epoxy resin and a filter filled with ECCOSORB CR-110 epoxy resin. The proposed design and assembly technology are versatile for various compounds and provide highly repeatable geometric and microwave characteristics. Furthermore, we demonstrate that these low-pass coaxial filters can be effectively utilized to improve superconducting qubit relaxation due to suppressing standing waves originating from reflections in control coaxial cables.

arXiv:2210.15301•Applied Physics Letters•Nov 13, 2023•13 citations
In this article we report on the design, fabrication, and tests of microfabricated broadband filters suitable for proper electromagnetic thermalization of electrical lines connected to sensitive quantum electronics experiments performed at dilution fridge temperatures. Compared to previous such miniature filters, the new design improves on performance and reliability. These filters can be packed in space-saving cases with either single or multicontact connector. Measured performance in the accessible range compares well to simulations. We use these simulations to discuss the effectiveness of these filters for electromagnetic thermalization at 30mK.
In experiments on single electron devices, the electromagnetic noise from parts of the apparatus at temperatures higher than that of the device can dramatically increase the tunnel rates out of the Coulomb-blocked state and therefore increase the device error rate. The electrical lines must therefore be filtered adequately. We derive simple expressions for calculating the required attenuation coefficient. We describe a wide-band miniature dissipative filter functioning at cryogenic temperatures. The effective thermalization of an experiment at 30 mK can be obtained by placing four of these filters in series at temperatures ranging from 4 K to 30 mK.
The careful filtering of microwave electromagnetic radiation is critical for controlling the electromagnetic environment for experiments in solid-state quantum information processing and quantum metrology at millikelvin temperatures. We describe the design and fabrication of a coaxial filter assembly and demonstrate that its performance is in excellent agreement with theoretical modelling. We further perform an indicative test of the operation of the filters by making current-voltage measurements of small, underdamped Josephson junctions at 15 mK.
We designed and fabricated miniature low-pass metal powder filters suitable for noise-sensitive measurements at cryogenic temperatures. In comparison with previous powder filters, our filters have a much better frequency response and significantly smaller dimensions (0.7 cm(3) including the plugs) and can also be used as hermetic feedthroughs at low temperatures. Their transmission characteristics are smooth, contain no ripples, and have a steep decay above the cutoff frequency. At 4.2 K the cutoff frequency of a single filter is f(c)=1 MHz and the roll-off is -50 dB per decade. All of the fabricated filters have identical frequency responses at 4.2 K and their characteristics are reliably reproducible.
This study presents the mechanical design and analysis of a quantum electro-optical transducer engineered to operate at millikelvin temperatures within a dilution refrigerator. The transducer enables bidirectional microwave-optical frequency conversion through a hybrid architecture that integrates a superconducting radiofrequency (SRF) cavity with an electro-optic optical cavity. Among several design options investigated, the configuration offering the best thermal and mechanical performance was selected, yielding a robust solution with reduced sensitivity to fabrication tolerances, improved heat dissipation, as well as alignment precision. The design ensures uniform temperature distribution, enabling higher laser pump powers and, thus, increased conversion efficiency, while maintaining mechanical stresses safely below the material yield strength. Electromagnetic simulations further validate the design, demonstrating enhanced coupling between the optical and microwave modes, as well as a broader tuning range achieved with smaller tuner displacements.
Cryogenic confocal microscopy is a powerful method for studying solid state quantum devices such as single photon sources and optically controlled qubits. While the vast majority of such studies have been conducted at temperatures of a few Kelvin, experiments involving fragile quantum effects often require lower operating temperatures. To also allow for electrical dynamic control, microwave connectivity is required. For polarization-sensitive studies, free space optical access is advantageous compared to fiber coupling. Here we present a confocal microscope in a dilution refrigerator providing all the above features at temperatures below 100 mK. The installed high frequency cabling meets the requirements for state-of-the-art spin qubit experiments. As another unique advantage of our system, the sample fitting inside a large puck can be exchanged while keeping the cryostat cold with minimal realignment. Assessing the performance of the instrument, we demonstrate confocal imaging, sub-nanosecond modulation of the emission wavelength of a suitable sample, and an electron temperature of 76 mK. While the instrument was constructed primarily with the development of optical interfaces to electrically controlled qubits in mind, it can be used for many experiments involving quantum transport, solid state quantum optics, and microwave-optical transducers.
Electromagnetic noise is one of the main external factors decreasing superconducting qubit coherence. Matched coaxial filters can prevent microwave and IR photons' negative influence on superconducting quantum circuits. In this report, we describe the design and fabrication process of matched coaxial filters for noise-sensitive measurements at millikelvin temperatures. A robust transmission coefficient and ultralow reflection loss of −20 dB in the frequency range up to 20 GHz is achieved. Fabricated low-pass filters have linear transmission and reflection characteristics with 3 dB-cutoff frequency of 1.5–2.5 GHz. A method for extracting the propagation constant and filter impedance from scattering parameter measurements is demonstrated. This method is experimentally approved on a filter with a compound of Cu powder and Stycast epoxy resin and a filter filled with ECCOSORB CR-110 epoxy resin. The proposed design and assembly technology are versatile for various compounds and provide highly repeatable geometric and microwave characteristics. Furthermore, we demonstrate that these low-pass coaxial filters can be effectively utilized to improve superconducting qubit relaxation due to suppressing standing waves originating from reflections in control coaxial cables.