We describe how to perform fast quantum limited readout of a solid state qubit biased at its degeneracy point. The method is based on homodyne detection of the phase of a microwave signal reflected by a slow oscillator coupled to the qubit. Analyzing the whole quantum readout process, we find that the detection is indeed quantum limited and that this limit may be reached even using a resonance circuit with a low quality factor, thus enabling the use of short measurement pulses. As an example, we discuss in detail the readout of a Cooper-pair box capacitively coupled to a lumped element $\mathit{LC}$ oscillator. Furthermore, we give formulas for the backaction while not measuring, and discuss optimal parameters for a realistic design capable of fast $(\ensuremath{\sim}50\phantom{\rule{0.3em}{0ex}}\mathrm{ns})$ single-shot readout.
We describe how to perform fast quantum limited readout of a solid state qubit biased at its degeneracy point. The method is based on homodyne detection of the phase of a microwave signal reflected by a slow oscillator coupled to the qubit. Analyzing the whole quantum readout process, we find that the detection is indeed quantum limited and that this limit may be reached even using a resonance circuit with a low quality factor, thus enabling the use of short measurement pulses. As an example, we discuss in detail the readout of a Cooper-pair box capacitively coupled to a lumped element LC oscillator. Furthermore, we give formulas for the backaction while not measuring, and discuss optimal parameters for a realistic design capable of fast (\ensuremath∼50ns) single-shot readout.
In this work we consider measurements on quantum systems emphasizing\non read-out of superconducting qubits. The qubit is always coupled to an\nenvironment, containing a macroscopic number of degrees of freedom. This\nperturbs the qubit and destroys the phase coherence of the quantum state.\nOne tries to minimize this destructive effect by encoding the quantum information in quantum states which do not couple strongly to the dominant\nnoise sources. It is therefore necessary to design read-out methods that can\ndistinguish these states.\n\nWe focus primarily on the single Cooper-pair box (SCB) charge qubit, whose\nproperties are based on the Josephson effect and Coulumb blockade in superconducting electrical circuits. By encoding the information in the qubit\nenergy eigenstates, it is possible to protect it from the most dangerous decoherence source - charge fluctuations in the environment. We investigate\nthe measurement setup, where the SCB is coupled to a lumped element LCoscillator whose resonance frequency is orders of magnitude smaller than the qubit energy splitting. In this regime the SCB will act as an effective positive or negative capacitance, depending on the quantum state. This quantum capacitance then shifts the oscillator resonance frequency, which can be detected in a homodyne phase measurement.\n\nWe have found that reading out a charge qubit by measuring its quantum\ncapacitance in this manner is quantum limited, independently of the oscillator\nquality factor Q. Moreover, we have found that the low-Q oscillator\nis advantageous for the measurement in two ways: first, such an oscillator\nbetter protects the qubit from thermal dephasing, and, second, it allows to\nincrease the speed of the read-out, making it possible to distinguish the qubit states in a single shot measurement.
We have fabricated a single Cooper-pair box (SCB) together with an on-chip lumped element resonator. By utilizing the quantum capacitance of the SCB, its state can be read out by detecting the phase of a radio-frequency signal reflected off the resonator. The resonator was optimized for fast readout. By studying quasiparticle tunneling events in the SCB, we have characterized the performance of the readout and found that we can perform a single-shot parity measurement, with a signal-to-noise ratio of 1, in approximately 50 ns. This is an order of magnitude faster than previously reported measurements.
We discuss the current situation concerning measurement and readout of Josephson-junction based qubits. In particular, we focus attention on dispersive low-dissipation techniques involving reflection of radiation from an oscillator circuit coupled to a qubit, allowing single-shot determination of the state of the qubit. In particular, we develop a formalism describing a charge qubit read out by measuring its effective (quantum) capacitance. To exemplify, we also give explicit formulas for the readout time.
We discuss the current situation concerning measurement and readout of Josephson-junction based qubits. In particular, we focus attention on dispersive low-dissipation techniques involving reflection of radiation from an oscillator circuit coupled to a qubit, allowing single-shot determination of the state of the qubit. In particular, we develop a formalism describing a charge qubit read out by measuring its effective (quantum) capacitance. To exemplify, we also give explicit formulas for the readout time.
Though superconducting qubits offer the potential for a scalable quantum computing architecture, the high-fidelity readout necessary to execute practical algorithms has thus far remained elusive. Moreover, achievements toward high fidelity have been accompanied by either long measurement times or demolition of the quantum state. In this dissertation, we address these issues with the novel integration of two ultralow-noise, superconducting amplifiers into separate dispersive flux qubit measurements. We first demonstrate a flux qubit inductively coupled to a 1.294-GHz nonlinear oscillator formed by a capacitively shunted DC SQUID. The frequency of the oscillator is modulated by the state of the qubit and is detected via microwave reflectometry. A microstrip SQUID (Superconducting QUantum Interference Device) amplifier (MSA) is used to increase the sensitivity of the measurement over that of a semiconductor amplifier. In the second experiment, we report measurements of a flux qubit coupled via a shared inductance to a quasi-lumped element 5.78-GHz readout resonator formed by the parallel combination of an interdigitated capacitor and a meander line inductor. The system noise is substantially reduced by a near-quantum-limited Josephson parametric amplifier (paramp).We present measurements of increased fidelity and reduced measurement backaction using the MSA at readout excitation levels as low as one hundredth of a photon in the readout resonator, observing a 4.5-fold increase in the readout visibility. Furthermore, at low readout excitation levels below one tenth of a photon in the readout resonator, no reduction in T1 is observed, potentially enabling continuous monitoring of the qubit state. Using the paramp, we demonstrate a continuous, high-fidelity readout with sufficient bandwidth and signal-to-noise ratio to resolve quantum jumps in the flux qubit. This is enabled by a readout which discriminates between the readout pointer state distributions to an error below one part in 1000. This, along with the ability to make many successive readouts in a time T1, permits the use of heralding to ensure initialization to a fiducial state, such as the ground state. This method enables us to eliminate errors due to spurious thermal population, increasing the fidelity to 93.9%. Finally, we use heralding to introduce a simple, fast qubit reset protocol without changing the system parameters to induce Purcell relaxation.
Though superconducting qubits offer the potential for a scalable quantum computing architecture, the high-fidelity readout necessary to execute practical algorithms has thus far remained elusive. Moreover, achievements toward high fidelity have been accompanied by either long measurement times or demolition of the quantum state. In this dissertation, we address these issues with the novel integration of two ultralow-noise, superconducting amplifiers into separate dispersive flux qubit measurements. We first demonstrate a flux qubit inductively coupled to a 1.294-GHz nonlinear oscillator formed by a capacitively shunted DC SQUID. The frequency of the oscillator is modulated by the state of the qubit and is detected via microwave reflectometry. A microstrip SQUID (Superconducting QUantum Interference Device) amplifier (MSA) is used to increase the sensitivity of the measurement over that of a semiconductor amplifier. In the second experiment, we report measurements of a flux qubit coupled via a shared inductance to a quasi-lumped element 5.78-GHz readout resonator formed by the parallel combination of an interdigitated capacitor and a meander line inductor. The system noise is substantially reduced by a near-quantum-limited Josephson parametric amplifier (paramp).We present measurements of increased fidelity and reduced measurement backaction using the MSA at readout excitation levels as low as one hundredth of a photon in the readout resonator, observing a 4.5-fold increase in the readout visibility. Furthermore, at low readout excitation levels below one tenth of a photon in the readout resonator, no reduction in T1 is observed, potentially enabling continuous monitoring of the qubit state. Using the paramp, we demonstrate a continuous, high-fidelity readout with sufficient bandwidth and signal-to-noise ratio to resolve quantum jumps in the flux qubit. This is enabled by a readout which discriminates between the readout pointer state distributions to an error below one part in 1000. This, along with the ability to make many successive readouts in a time T1, permits the use of heralding to ensure initialization to a fiducial state, such as the ground state. This method enables us to eliminate errors due to spurious thermal population, increasing the fidelity to 93.9%. Finally, we use heralding to introduce a simple, fast qubit reset protocol without changing the system parameters to induce Purcell relaxation.