Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Optimization of superconducting flux qubit readout using near-quantum-limited amplifiers - eScholarship

Jedediah E Johnson

Published Jan 1, 2012• 0 citations
OpenAlex

Abstract

Though superconducting qubits offer the potential for a scalable quantum computing architecture, the high-fidelity readout necessary to execute practical algorithms has thus far remained elusive. Moreover, achievements toward high fidelity have been accompanied by either long measurement times or demolition of the quantum state. In this dissertation, we address these issues with the novel integration of two ultralow-noise, superconducting amplifiers into separate dispersive flux qubit measurements. We first demonstrate a flux qubit inductively coupled to a 1.294-GHz nonlinear oscillator formed by a capacitively shunted DC SQUID. The frequency of the oscillator is modulated by the state of the qubit and is detected via microwave reflectometry. A microstrip SQUID (Superconducting QUantum Interference Device) amplifier (MSA) is used to increase the sensitivity of the measurement over that of a semiconductor amplifier. In the second experiment, we report measurements of a flux qubit coupled via a shared inductance to a quasi-lumped element 5.78-GHz readout resonator formed by the parallel combination of an interdigitated capacitor and a meander line inductor. The system noise is substantially reduced by a near-quantum-limited Josephson parametric amplifier (paramp).We present measurements of increased fidelity and reduced measurement backaction using the MSA at readout excitation levels as low as one hundredth of a photon in the readout resonator, observing a 4.5-fold increase in the readout visibility. Furthermore, at low readout excitation levels below one tenth of a photon in the readout resonator, no reduction in T1 is observed, potentially enabling continuous monitoring of the qubit state. Using the paramp, we demonstrate a continuous, high-fidelity readout with sufficient bandwidth and signal-to-noise ratio to resolve quantum jumps in the flux qubit. This is enabled by a readout which discriminates between the readout pointer state distributions to an error below one part in 1000. This, along with the ability to make many successive readouts in a time T1, permits the use of heralding to ensure initialization to a fiducial state, such as the ground state. This method enables us to eliminate errors due to spurious thermal population, increasing the fidelity to 93.9%. Finally, we use heralding to introduce a simple, fast qubit reset protocol without changing the system parameters to induce Purcell relaxation.

Related papers

Optimization of superconducting flux qubit readout using near-quantum-limited amplifiers

Jedediah E Johnson

Though superconducting qubits offer the potential for a scalable quantum computing architecture, the high-fidelity readout necessary to execute practical algorithms has thus far remained elusive. Moreover, achievements toward high fidelity have been accompanied by either long measurement times or demolition of the quantum state. In this dissertation, we address these issues with the novel integration of two ultralow-noise, superconducting amplifiers into separate dispersive flux qubit measurements. We first demonstrate a flux qubit inductively coupled to a 1.294-GHz nonlinear oscillator formed by a capacitively shunted DC SQUID. The frequency of the oscillator is modulated by the state of the qubit and is detected via microwave reflectometry. A microstrip SQUID (Superconducting QUantum Interference Device) amplifier (MSA) is used to increase the sensitivity of the measurement over that of a semiconductor amplifier. In the second experiment, we report measurements of a flux qubit coupled via a shared inductance to a quasi-lumped element 5.78-GHz readout resonator formed by the parallel combination of an interdigitated capacitor and a meander line inductor. The system noise is substantially reduced by a near-quantum-limited Josephson parametric amplifier (paramp).We present measurements of increased fidelity and reduced measurement backaction using the MSA at readout excitation levels as low as one hundredth of a photon in the readout resonator, observing a 4.5-fold increase in the readout visibility. Furthermore, at low readout excitation levels below one tenth of a photon in the readout resonator, no reduction in T1 is observed, potentially enabling continuous monitoring of the qubit state. Using the paramp, we demonstrate a continuous, high-fidelity readout with sufficient bandwidth and signal-to-noise ratio to resolve quantum jumps in the flux qubit. This is enabled by a readout which discriminates between the readout pointer state distributions to an error below one part in 1000. This, along with the ability to make many successive readouts in a time T1, permits the use of heralding to ensure initialization to a fiducial state, such as the ground state. This method enables us to eliminate errors due to spurious thermal population, increasing the fidelity to 93.9%. Finally, we use heralding to introduce a simple, fast qubit reset protocol without changing the system parameters to induce Purcell relaxation.

•Jan 1, 2012•2 citations

Dispersive readout of a flux qubit at the single-photon level

Jedediah E Johnson, Emile Hoskinson, Chris Macklin +3 more

A superconducting flux qubit is inductively coupled to a superconducting quantum interference device (SQUID) magnetometer, capacitively shunted to form a 1.294-GHz resonator. The qubit-state-dependent resonator frequency is weakly probed with a microwave signal and detected with a microstrip SQUID amplifier. At a mean resonator occupation $\overline{n}=1.5$ photons, the readout visibility is increased by a factor of 4.5 over that using a cryogenic semiconductor amplifier. As $\overline{n}$ is increased from 0.008 to 0.1, no reduction in ${T}_{1}$ is observed, potentially enabling continuous monitoring of the qubit state.

arXiv:1109.2858•Physical Review B•Dec 15, 2011•20 citations

Superconducting quantum interference device with frequency-dependent damping: Readout of flux qubits

Timothy L. Robertson, B. L. T. Plourde, T. Hime +4 more

Recent experiments on superconducting flux qubits, consisting of a superconducting loop interrupted by Josephson junctions, have demonstrated quantum coherence between two different quantum states. The state of the qubit is measured with a superconducting quantum interference device (SQUID). Such measurements require the SQUID to have high resolution while exerting minimal backaction on the qubit. By designing shunts across the SQUID junctions appropriately, one can improve the measurement resolution without increasing the backaction significantly. Using a path-integral approach to analyze the Caldeira-Leggett model, we calculate the narrowing of the distribution of the switching events from the zero-voltage state of the SQUID for arbitrary shunt admittances, focusing on shunts consisting of a capacitance ${C}_{s}$ and resistance ${R}_{s}$ in series. To test this model, we fabricated a dc SQUID in which each junction is shunted with a thin-film interdigitated capacitor in series with a resistor, and measured the switching distribution as a function of temperature and applied magnetic flux. After accounting for the damping due to the SQUID leads, we found good agreement between the measured escape rates and the predictions of our model. We analyze the backaction of a shunted symmetric SQUID on a flux qubit. For the given parameters of our SQUID and realistic parameters for a flux qubit, at the degeneracy point we find a relaxation time of $113\phantom{\rule{0.3em}{0ex}}\ensuremath{\mu}\mathrm{s}$, which limits the decoherence time to $226\phantom{\rule{0.3em}{0ex}}\ensuremath{\mu}\mathrm{s}$. Based on our analysis of the escape process, we determine that a SQUID with purely capacitive shunts should have narrow switching distributions and no dissipation.

Physical Review B•Jul 11, 2005•23 citations

Quantum Jumps and Measurement Backaction in a Superconducting Qubit

D. H. Slichter

Real-time monitoring of a quantum state provides powerful tools for studying the backaction of quantum measurement and performing quantum feedback. Historically, this monitoring capability has been the exclusive province of atomic and optical physics. This thesis describes the implementation of the first such high-fidelity readout scheme in a solid state circuit, a superconducting quantum bit (qubit) coupled to a microwave cavity in the circuit quantum electrodynamics (circuit QED) architecture. The qubit-state-dependent resonance frequency of the cavity is probed with a microwave drive tone, and the resulting signal amplified using a fast, ultralow-noise superconducting parametric amplifier. This arrangement enables the observation of quantum jumps between the qubit states in real time. The ability to monitor the qubit continuously with high fidelity and resolve quantum jumps can be used to investigate the backaction of the measurement process on the qubit. This thesis examines the quantum Zeno effect--where strong measurement inhibits the evolution of a quantum system-- as well as the transition to non-ideal measurement with increasing measurement strength in the circuit QED architecture, a phenomenon shown to be due to the upconversion of low-frequency dephasing noise. These data allow probes of ``universal'' flux noise in previously inaccessible frequency ranges. The work presented here opens the door for quantum feedback and error correction in solid-state quantum systems using continuous weak measurement.

•Jan 1, 2011•10 citations

The Josephson parametric oscillator - From microscopic studies to single-shot qubit readout

Philip Krantz

Circuit quantum electrodynamics (cQED) is a prominent platform for quantum information processing, in which microwave photons are confined into resonant cavities coupled to superconducting quantum bits (qubits). The large effective dipole moment of the qubit, in combination with the high energy density of the quasi 1-D resonator allow these systems to enter the so-called strong coupling regime. The quantum state of the qubit can then be assessed by probing the frequency of the resonator, protecting the qubit from otherwise losing its energy to the environment. However, eventhough this so-called dispersive readout technique has proven useful, it is often in itself insufficient to render single-shot readout performance | one of the crucial tasks required for realizing a quantum computer. This thesis describes the demonstration of a single-shot readout technique forsuperconducting quantum bits, based on coupling the qubit to a frequency-tunable resonator. The backbone of our device is a 5 GHz quarter-wavelength coplanar waveguide resonator, terminated at one end by a non-linear inductance provided by a superconducting quantum interference device (SQUID). The SQUID acts as a flux-controlled boundary condition, which effectively changes the electrical length of the resonator. This enables the modulation of the resonant frequency by coupling microwave magnetic flux into the SQUID, using an on-chip transmission line. The modulation occurs on a timescale much faster than the photon loss out of the resonator and if the pump strength exceeds a threshold value set by the damping rate of the resonator, an intense photon field will build up inside the resonator | known as "parametric oscillations". By heterodyne detection of the output signal from the Josephson parametric oscillator (JPO), we first extracted two leading nonlinear effects of the system (dominating in different limits of applied magnetic flux). Next, we couple a qubit to the JPO and demonstrate that we can encode its quantum state onto the strong output field of the parametric oscillator (or lack thereof), rendering a signal-to-noise ratio sufficient for single-shot state detection and therefore also obviating a quantum limited parametric amplifier. The thesis also contains results from microscopic studies of the Josephson junctions, which we use to provide the necessary nonlinearities in the above mentioned devices. In particular, we show how the microstructure of the barrier layer and its atomic composition can be used to infer important electrical properties of the junctions. This knowledge allows us to better tailor the properties of Josephson-based devices.

•Jan 1, 2016•3 citations

Towards quantum-noise limited multiplexed microwave readout of qubits

Kevin P. O’Brien, Chris Macklin, David J. Hover +5 more

Coherent circuits based on superconducting elements hold tremendous promise for the practical implementation of quantum information technology: advanced computation, cryptography, and hardware simulation of complex materials systems are envisioned applications. Such circuits are essentially engineered atoms with level transitions in the 4-8 GHz regime; as such “read” and “write” operations are performed with the aid of fast microwave pulses and low-noise amplifiers, respectively. Recent advances in cavity-based superconducting parametric amplifiers have enabled real-time measurement and feedback in one and two qubits. We demonstrate a novel Josephson junction transmission-line based traveling-wave amplifier which employs sub-wavelength phase matching resonators to achieve high gain, several GHz of bandwidth, and near quantum-noise limited performance. Such devices will enable multiplexed qubit readout in integrated architectures comprised of a variety of microwave frequency analog and digital superconducting technologies: signal sources, multiplexers, ADCs, DACs, mixers, and amplifiers.

IEEE MTT-S International Microwave Symposium digest•May 1, 2016•2 citations
Though superconducting qubits offer the potential for a scalable quantum computing architecture, the high-fidelity readout necessary to execute practical algorithms has thus far remained elusive. Moreover, achievements toward high fidelity have been accompanied by either long measurement times or demolition of the quantum state. In this dissertation, we address these issues with the novel integration of two ultralow-noise, superconducting amplifiers into separate dispersive flux qubit measurements. We first demonstrate a flux qubit inductively coupled to a 1.294-GHz nonlinear oscillator formed by a capacitively shunted DC SQUID. The frequency of the oscillator is modulated by the state of the qubit and is detected via microwave reflectometry. A microstrip SQUID (Superconducting QUantum Interference Device) amplifier (MSA) is used to increase the sensitivity of the measurement over that of a semiconductor amplifier. In the second experiment, we report measurements of a flux qubit coupled via a shared inductance to a quasi-lumped element 5.78-GHz readout resonator formed by the parallel combination of an interdigitated capacitor and a meander line inductor. The system noise is substantially reduced by a near-quantum-limited Josephson parametric amplifier (paramp).We present measurements of increased fidelity and reduced measurement backaction using the MSA at readout excitation levels as low as one hundredth of a photon in the readout resonator, observing a 4.5-fold increase in the readout visibility. Furthermore, at low readout excitation levels below one tenth of a photon in the readout resonator, no reduction in T1 is observed, potentially enabling continuous monitoring of the qubit state. Using the paramp, we demonstrate a continuous, high-fidelity readout with sufficient bandwidth and signal-to-noise ratio to resolve quantum jumps in the flux qubit. This is enabled by a readout which discriminates between the readout pointer state distributions to an error below one part in 1000. This, along with the ability to make many successive readouts in a time T1, permits the use of heralding to ensure initialization to a fiducial state, such as the ground state. This method enables us to eliminate errors due to spurious thermal population, increasing the fidelity to 93.9%. Finally, we use heralding to introduce a simple, fast qubit reset protocol without changing the system parameters to induce Purcell relaxation.
Though superconducting qubits offer the potential for a scalable quantum computing architecture, the high-fidelity readout necessary to execute practical algorithms has thus far remained elusive. Moreover, achievements toward high fidelity have been accompanied by either long measurement times or demolition of the quantum state. In this dissertation, we address these issues with the novel integration of two ultralow-noise, superconducting amplifiers into separate dispersive flux qubit measurements. We first demonstrate a flux qubit inductively coupled to a 1.294-GHz nonlinear oscillator formed by a capacitively shunted DC SQUID. The frequency of the oscillator is modulated by the state of the qubit and is detected via microwave reflectometry. A microstrip SQUID (Superconducting QUantum Interference Device) amplifier (MSA) is used to increase the sensitivity of the measurement over that of a semiconductor amplifier. In the second experiment, we report measurements of a flux qubit coupled via a shared inductance to a quasi-lumped element 5.78-GHz readout resonator formed by the parallel combination of an interdigitated capacitor and a meander line inductor. The system noise is substantially reduced by a near-quantum-limited Josephson parametric amplifier (paramp).We present measurements of increased fidelity and reduced measurement backaction using the MSA at readout excitation levels as low as one hundredth of a photon in the readout resonator, observing a 4.5-fold increase in the readout visibility. Furthermore, at low readout excitation levels below one tenth of a photon in the readout resonator, no reduction in T1 is observed, potentially enabling continuous monitoring of the qubit state. Using the paramp, we demonstrate a continuous, high-fidelity readout with sufficient bandwidth and signal-to-noise ratio to resolve quantum jumps in the flux qubit. This is enabled by a readout which discriminates between the readout pointer state distributions to an error below one part in 1000. This, along with the ability to make many successive readouts in a time T1, permits the use of heralding to ensure initialization to a fiducial state, such as the ground state. This method enables us to eliminate errors due to spurious thermal population, increasing the fidelity to 93.9%. Finally, we use heralding to introduce a simple, fast qubit reset protocol without changing the system parameters to induce Purcell relaxation.
A superconducting flux qubit is inductively coupled to a superconducting quantum interference device (SQUID) magnetometer, capacitively shunted to form a 1.294-GHz resonator. The qubit-state-dependent resonator frequency is weakly probed with a microwave signal and detected with a microstrip SQUID amplifier. At a mean resonator occupation n‾=1.5\overline{n}=1.5n=1.5 photons, the readout visibility is increased by a factor of 4.5 over that using a cryogenic semiconductor amplifier. As n‾\overline{n}n is increased from 0.008 to 0.1, no reduction in T1{T}_{1}T1​ is observed, potentially enabling continuous monitoring of the qubit state.
Recent experiments on superconducting flux qubits, consisting of a superconducting loop interrupted by Josephson junctions, have demonstrated quantum coherence between two different quantum states. The state of the qubit is measured with a superconducting quantum interference device (SQUID). Such measurements require the SQUID to have high resolution while exerting minimal backaction on the qubit. By designing shunts across the SQUID junctions appropriately, one can improve the measurement resolution without increasing the backaction significantly. Using a path-integral approach to analyze the Caldeira-Leggett model, we calculate the narrowing of the distribution of the switching events from the zero-voltage state of the SQUID for arbitrary shunt admittances, focusing on shunts consisting of a capacitance Cs{C}_{s}Cs​ and resistance Rs{R}_{s}Rs​ in series. To test this model, we fabricated a dc SQUID in which each junction is shunted with a thin-film interdigitated capacitor in series with a resistor, and measured the switching distribution as a function of temperature and applied magnetic flux. After accounting for the damping due to the SQUID leads, we found good agreement between the measured escape rates and the predictions of our model. We analyze the backaction of a shunted symmetric SQUID on a flux qubit. For the given parameters of our SQUID and realistic parameters for a flux qubit, at the degeneracy point we find a relaxation time of $113\phantom{\rule{0.3em}{0ex}}\ensuremath{\mu}\mathrm{s}$, which limits the decoherence time to $226\phantom{\rule{0.3em}{0ex}}\ensuremath{\mu}\mathrm{s}$. Based on our analysis of the escape process, we determine that a SQUID with purely capacitive shunts should have narrow switching distributions and no dissipation.
Real-time monitoring of a quantum state provides powerful tools for studying the backaction of quantum measurement and performing quantum feedback. Historically, this monitoring capability has been the exclusive province of atomic and optical physics. This thesis describes the implementation of the first such high-fidelity readout scheme in a solid state circuit, a superconducting quantum bit (qubit) coupled to a microwave cavity in the circuit quantum electrodynamics (circuit QED) architecture. The qubit-state-dependent resonance frequency of the cavity is probed with a microwave drive tone, and the resulting signal amplified using a fast, ultralow-noise superconducting parametric amplifier. This arrangement enables the observation of quantum jumps between the qubit states in real time. The ability to monitor the qubit continuously with high fidelity and resolve quantum jumps can be used to investigate the backaction of the measurement process on the qubit. This thesis examines the quantum Zeno effect--where strong measurement inhibits the evolution of a quantum system-- as well as the transition to non-ideal measurement with increasing measurement strength in the circuit QED architecture, a phenomenon shown to be due to the upconversion of low-frequency dephasing noise. These data allow probes of ``universal'' flux noise in previously inaccessible frequency ranges. The work presented here opens the door for quantum feedback and error correction in solid-state quantum systems using continuous weak measurement.
Circuit quantum electrodynamics (cQED) is a prominent platform for quantum information processing, in which microwave photons are confined into resonant cavities coupled to superconducting quantum bits (qubits). The large effective dipole moment of the qubit, in combination with the high energy density of the quasi 1-D resonator allow these systems to enter the so-called strong coupling regime. The quantum state of the qubit can then be assessed by probing the frequency of the resonator, protecting the qubit from otherwise losing its energy to the environment. However, eventhough this so-called dispersive readout technique has proven useful, it is often in itself insufficient to render single-shot readout performance | one of the crucial tasks required for realizing a quantum computer. This thesis describes the demonstration of a single-shot readout technique forsuperconducting quantum bits, based on coupling the qubit to a frequency-tunable resonator. The backbone of our device is a 5 GHz quarter-wavelength coplanar waveguide resonator, terminated at one end by a non-linear inductance provided by a superconducting quantum interference device (SQUID). The SQUID acts as a flux-controlled boundary condition, which effectively changes the electrical length of the resonator. This enables the modulation of the resonant frequency by coupling microwave magnetic flux into the SQUID, using an on-chip transmission line. The modulation occurs on a timescale much faster than the photon loss out of the resonator and if the pump strength exceeds a threshold value set by the damping rate of the resonator, an intense photon field will build up inside the resonator | known as "parametric oscillations". By heterodyne detection of the output signal from the Josephson parametric oscillator (JPO), we first extracted two leading nonlinear effects of the system (dominating in different limits of applied magnetic flux). Next, we couple a qubit to the JPO and demonstrate that we can encode its quantum state onto the strong output field of the parametric oscillator (or lack thereof), rendering a signal-to-noise ratio sufficient for single-shot state detection and therefore also obviating a quantum limited parametric amplifier. The thesis also contains results from microscopic studies of the Josephson junctions, which we use to provide the necessary nonlinearities in the above mentioned devices. In particular, we show how the microstructure of the barrier layer and its atomic composition can be used to infer important electrical properties of the junctions. This knowledge allows us to better tailor the properties of Josephson-based devices.
Coherent circuits based on superconducting elements hold tremendous promise for the practical implementation of quantum information technology: advanced computation, cryptography, and hardware simulation of complex materials systems are envisioned applications. Such circuits are essentially engineered atoms with level transitions in the 4-8 GHz regime; as such “read” and “write” operations are performed with the aid of fast microwave pulses and low-noise amplifiers, respectively. Recent advances in cavity-based superconducting parametric amplifiers have enabled real-time measurement and feedback in one and two qubits. We demonstrate a novel Josephson junction transmission-line based traveling-wave amplifier which employs sub-wavelength phase matching resonators to achieve high gain, several GHz of bandwidth, and near quantum-noise limited performance. Such devices will enable multiplexed qubit readout in integrated architectures comprised of a variety of microwave frequency analog and digital superconducting technologies: signal sources, multiplexers, ADCs, DACs, mixers, and amplifiers.