Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1109.2858 · Physical Review B

Dispersive readout of a flux qubit at the single-photon level

Jedediah E Johnson, Emile Hoskinson, Chris Macklin, D. H. Slichter, Irfan A. Siddiqi, John L. Clarke

Published Dec 15, 2011• 20 citations
arXivHTMLPDF

Abstract

A superconducting flux qubit is inductively coupled to a superconducting quantum interference device (SQUID) magnetometer, capacitively shunted to form a 1.294-GHz resonator. The qubit-state-dependent resonator frequency is weakly probed with a microwave signal and detected with a microstrip SQUID amplifier. At a mean resonator occupation $\overline{n}=1.5$ photons, the readout visibility is increased by a factor of 4.5 over that using a cryogenic semiconductor amplifier. As $\overline{n}$ is increased from 0.008 to 0.1, no reduction in ${T}_{1}$ is observed, potentially enabling continuous monitoring of the qubit state.

DOI
10.1103/physrevb.84.220503

Related papers

Optimization of superconducting flux qubit readout using near-quantum-limited amplifiers

Jedediah E Johnson

Though superconducting qubits offer the potential for a scalable quantum computing architecture, the high-fidelity readout necessary to execute practical algorithms has thus far remained elusive. Moreover, achievements toward high fidelity have been accompanied by either long measurement times or demolition of the quantum state. In this dissertation, we address these issues with the novel integration of two ultralow-noise, superconducting amplifiers into separate dispersive flux qubit measurements. We first demonstrate a flux qubit inductively coupled to a 1.294-GHz nonlinear oscillator formed by a capacitively shunted DC SQUID. The frequency of the oscillator is modulated by the state of the qubit and is detected via microwave reflectometry. A microstrip SQUID (Superconducting QUantum Interference Device) amplifier (MSA) is used to increase the sensitivity of the measurement over that of a semiconductor amplifier. In the second experiment, we report measurements of a flux qubit coupled via a shared inductance to a quasi-lumped element 5.78-GHz readout resonator formed by the parallel combination of an interdigitated capacitor and a meander line inductor. The system noise is substantially reduced by a near-quantum-limited Josephson parametric amplifier (paramp).We present measurements of increased fidelity and reduced measurement backaction using the MSA at readout excitation levels as low as one hundredth of a photon in the readout resonator, observing a 4.5-fold increase in the readout visibility. Furthermore, at low readout excitation levels below one tenth of a photon in the readout resonator, no reduction in T1 is observed, potentially enabling continuous monitoring of the qubit state. Using the paramp, we demonstrate a continuous, high-fidelity readout with sufficient bandwidth and signal-to-noise ratio to resolve quantum jumps in the flux qubit. This is enabled by a readout which discriminates between the readout pointer state distributions to an error below one part in 1000. This, along with the ability to make many successive readouts in a time T1, permits the use of heralding to ensure initialization to a fiducial state, such as the ground state. This method enables us to eliminate errors due to spurious thermal population, increasing the fidelity to 93.9%. Finally, we use heralding to introduce a simple, fast qubit reset protocol without changing the system parameters to induce Purcell relaxation.

•Jan 1, 2012•2 citations

Optimization of superconducting flux qubit readout using near-quantum-limited amplifiers - eScholarship

Jedediah E Johnson

Though superconducting qubits offer the potential for a scalable quantum computing architecture, the high-fidelity readout necessary to execute practical algorithms has thus far remained elusive. Moreover, achievements toward high fidelity have been accompanied by either long measurement times or demolition of the quantum state. In this dissertation, we address these issues with the novel integration of two ultralow-noise, superconducting amplifiers into separate dispersive flux qubit measurements. We first demonstrate a flux qubit inductively coupled to a 1.294-GHz nonlinear oscillator formed by a capacitively shunted DC SQUID. The frequency of the oscillator is modulated by the state of the qubit and is detected via microwave reflectometry. A microstrip SQUID (Superconducting QUantum Interference Device) amplifier (MSA) is used to increase the sensitivity of the measurement over that of a semiconductor amplifier. In the second experiment, we report measurements of a flux qubit coupled via a shared inductance to a quasi-lumped element 5.78-GHz readout resonator formed by the parallel combination of an interdigitated capacitor and a meander line inductor. The system noise is substantially reduced by a near-quantum-limited Josephson parametric amplifier (paramp).We present measurements of increased fidelity and reduced measurement backaction using the MSA at readout excitation levels as low as one hundredth of a photon in the readout resonator, observing a 4.5-fold increase in the readout visibility. Furthermore, at low readout excitation levels below one tenth of a photon in the readout resonator, no reduction in T1 is observed, potentially enabling continuous monitoring of the qubit state. Using the paramp, we demonstrate a continuous, high-fidelity readout with sufficient bandwidth and signal-to-noise ratio to resolve quantum jumps in the flux qubit. This is enabled by a readout which discriminates between the readout pointer state distributions to an error below one part in 1000. This, along with the ability to make many successive readouts in a time T1, permits the use of heralding to ensure initialization to a fiducial state, such as the ground state. This method enables us to eliminate errors due to spurious thermal population, increasing the fidelity to 93.9%. Finally, we use heralding to introduce a simple, fast qubit reset protocol without changing the system parameters to induce Purcell relaxation.

•Jan 1, 2012•0 citations

Qubit dispersive readout scheme with a microstrip superconducting quantum interference device amplifier

Sébastien Michotte

A flux qubit readout scheme involving a dispersive technique coupled to a microstrip superconducting quantum interference device (SQUID) amplifier has been tested experimentally. Thanks to the almost quantum limited noise of this amplifier at low temperature, this readout device is very promising for a design with actual qubits. Its proof of principle and low noise performance have been tested by simulating the qubit presence by applying a tiny flux change in the input SQUID. The resonant frequency of the amplifier is adjusted in situ with a varactor diode to approach the frequency of the tank circuit. Two operating modes (crossing or anticrossing regime) were identified.

Applied Physics Letters•Mar 23, 2009•9 citations

Microwave readout scheme for a Josephson phase qubit

Tobias Wirth, Jürgen Lisenfeld, Alexander V. Lukashenko +1 more

We present experimental results on a microwave scheme for reading out a Josephson phase qubit. A capacitively shunted superconducting quantum interference device (SQUID) is used as a nonlinear resonator which is inductively coupled to the qubit. The flux state of the qubit is detected by measuring the amplitude and phase of a microwave pulse reflected from the SQUID resonator. By this low-dissipative method, the qubit state measurement time is reduced to 25 μs, which is much faster than the conventional readout performed by switching the SQUID to its nonzero dc voltage state. The readout scheme presented here allows for reading out multiple qubits using a single microwave line by employing frequency-division multiplexing.

arXiv:1010.0954•Applied Physics Letters•Dec 27, 2010•13 citations

Dispersive readout scheme for a Josephson phase qubit

Wirth, Tobias

We present experimental results on a dispersive scheme for reading out a Josephson phase qubit. A capacitively shunted dc-SQUID is used as a nonlinear resonator which is inductively coupled to the qubit. We detect the flux state of the qubit by measuring the amplitude and phase of a microwave pulse reflected from the SQUID resonator. By this low-dissipative method, we reduce the qubit state measurement time down to 25 microseconds, which is much faster than using the conventional readout performed by switching the SQUID to its non-zero dc voltage state. The demonstrated readout scheme allows for reading out multiple qubits using a single microwave line by employing frequency-division multiplexing.

Verhandlungen der Deutschen Physikalischen Gesellschaft•Jan 1, 2011•0 citations

The Josephson parametric oscillator - From microscopic studies to single-shot qubit readout

Philip Krantz

Circuit quantum electrodynamics (cQED) is a prominent platform for quantum information processing, in which microwave photons are confined into resonant cavities coupled to superconducting quantum bits (qubits). The large effective dipole moment of the qubit, in combination with the high energy density of the quasi 1-D resonator allow these systems to enter the so-called strong coupling regime. The quantum state of the qubit can then be assessed by probing the frequency of the resonator, protecting the qubit from otherwise losing its energy to the environment. However, eventhough this so-called dispersive readout technique has proven useful, it is often in itself insufficient to render single-shot readout performance | one of the crucial tasks required for realizing a quantum computer. This thesis describes the demonstration of a single-shot readout technique forsuperconducting quantum bits, based on coupling the qubit to a frequency-tunable resonator. The backbone of our device is a 5 GHz quarter-wavelength coplanar waveguide resonator, terminated at one end by a non-linear inductance provided by a superconducting quantum interference device (SQUID). The SQUID acts as a flux-controlled boundary condition, which effectively changes the electrical length of the resonator. This enables the modulation of the resonant frequency by coupling microwave magnetic flux into the SQUID, using an on-chip transmission line. The modulation occurs on a timescale much faster than the photon loss out of the resonator and if the pump strength exceeds a threshold value set by the damping rate of the resonator, an intense photon field will build up inside the resonator | known as "parametric oscillations". By heterodyne detection of the output signal from the Josephson parametric oscillator (JPO), we first extracted two leading nonlinear effects of the system (dominating in different limits of applied magnetic flux). Next, we couple a qubit to the JPO and demonstrate that we can encode its quantum state onto the strong output field of the parametric oscillator (or lack thereof), rendering a signal-to-noise ratio sufficient for single-shot state detection and therefore also obviating a quantum limited parametric amplifier. The thesis also contains results from microscopic studies of the Josephson junctions, which we use to provide the necessary nonlinearities in the above mentioned devices. In particular, we show how the microstructure of the barrier layer and its atomic composition can be used to infer important electrical properties of the junctions. This knowledge allows us to better tailor the properties of Josephson-based devices.

•Jan 1, 2016•3 citations
A superconducting flux qubit is inductively coupled to a superconducting quantum interference device (SQUID) magnetometer, capacitively shunted to form a 1.294-GHz resonator. The qubit-state-dependent resonator frequency is weakly probed with a microwave signal and detected with a microstrip SQUID amplifier. At a mean resonator occupation n‾=1.5\overline{n}=1.5n=1.5 photons, the readout visibility is increased by a factor of 4.5 over that using a cryogenic semiconductor amplifier. As n‾\overline{n}n is increased from 0.008 to 0.1, no reduction in T1{T}_{1}T1​ is observed, potentially enabling continuous monitoring of the qubit state.
Though superconducting qubits offer the potential for a scalable quantum computing architecture, the high-fidelity readout necessary to execute practical algorithms has thus far remained elusive. Moreover, achievements toward high fidelity have been accompanied by either long measurement times or demolition of the quantum state. In this dissertation, we address these issues with the novel integration of two ultralow-noise, superconducting amplifiers into separate dispersive flux qubit measurements. We first demonstrate a flux qubit inductively coupled to a 1.294-GHz nonlinear oscillator formed by a capacitively shunted DC SQUID. The frequency of the oscillator is modulated by the state of the qubit and is detected via microwave reflectometry. A microstrip SQUID (Superconducting QUantum Interference Device) amplifier (MSA) is used to increase the sensitivity of the measurement over that of a semiconductor amplifier. In the second experiment, we report measurements of a flux qubit coupled via a shared inductance to a quasi-lumped element 5.78-GHz readout resonator formed by the parallel combination of an interdigitated capacitor and a meander line inductor. The system noise is substantially reduced by a near-quantum-limited Josephson parametric amplifier (paramp).We present measurements of increased fidelity and reduced measurement backaction using the MSA at readout excitation levels as low as one hundredth of a photon in the readout resonator, observing a 4.5-fold increase in the readout visibility. Furthermore, at low readout excitation levels below one tenth of a photon in the readout resonator, no reduction in T1 is observed, potentially enabling continuous monitoring of the qubit state. Using the paramp, we demonstrate a continuous, high-fidelity readout with sufficient bandwidth and signal-to-noise ratio to resolve quantum jumps in the flux qubit. This is enabled by a readout which discriminates between the readout pointer state distributions to an error below one part in 1000. This, along with the ability to make many successive readouts in a time T1, permits the use of heralding to ensure initialization to a fiducial state, such as the ground state. This method enables us to eliminate errors due to spurious thermal population, increasing the fidelity to 93.9%. Finally, we use heralding to introduce a simple, fast qubit reset protocol without changing the system parameters to induce Purcell relaxation.
Though superconducting qubits offer the potential for a scalable quantum computing architecture, the high-fidelity readout necessary to execute practical algorithms has thus far remained elusive. Moreover, achievements toward high fidelity have been accompanied by either long measurement times or demolition of the quantum state. In this dissertation, we address these issues with the novel integration of two ultralow-noise, superconducting amplifiers into separate dispersive flux qubit measurements. We first demonstrate a flux qubit inductively coupled to a 1.294-GHz nonlinear oscillator formed by a capacitively shunted DC SQUID. The frequency of the oscillator is modulated by the state of the qubit and is detected via microwave reflectometry. A microstrip SQUID (Superconducting QUantum Interference Device) amplifier (MSA) is used to increase the sensitivity of the measurement over that of a semiconductor amplifier. In the second experiment, we report measurements of a flux qubit coupled via a shared inductance to a quasi-lumped element 5.78-GHz readout resonator formed by the parallel combination of an interdigitated capacitor and a meander line inductor. The system noise is substantially reduced by a near-quantum-limited Josephson parametric amplifier (paramp).We present measurements of increased fidelity and reduced measurement backaction using the MSA at readout excitation levels as low as one hundredth of a photon in the readout resonator, observing a 4.5-fold increase in the readout visibility. Furthermore, at low readout excitation levels below one tenth of a photon in the readout resonator, no reduction in T1 is observed, potentially enabling continuous monitoring of the qubit state. Using the paramp, we demonstrate a continuous, high-fidelity readout with sufficient bandwidth and signal-to-noise ratio to resolve quantum jumps in the flux qubit. This is enabled by a readout which discriminates between the readout pointer state distributions to an error below one part in 1000. This, along with the ability to make many successive readouts in a time T1, permits the use of heralding to ensure initialization to a fiducial state, such as the ground state. This method enables us to eliminate errors due to spurious thermal population, increasing the fidelity to 93.9%. Finally, we use heralding to introduce a simple, fast qubit reset protocol without changing the system parameters to induce Purcell relaxation.
A flux qubit readout scheme involving a dispersive technique coupled to a microstrip superconducting quantum interference device (SQUID) amplifier has been tested experimentally. Thanks to the almost quantum limited noise of this amplifier at low temperature, this readout device is very promising for a design with actual qubits. Its proof of principle and low noise performance have been tested by simulating the qubit presence by applying a tiny flux change in the input SQUID. The resonant frequency of the amplifier is adjusted in situ with a varactor diode to approach the frequency of the tank circuit. Two operating modes (crossing or anticrossing regime) were identified.
We present experimental results on a microwave scheme for reading out a Josephson phase qubit. A capacitively shunted superconducting quantum interference device (SQUID) is used as a nonlinear resonator which is inductively coupled to the qubit. The flux state of the qubit is detected by measuring the amplitude and phase of a microwave pulse reflected from the SQUID resonator. By this low-dissipative method, the qubit state measurement time is reduced to 25 μs, which is much faster than the conventional readout performed by switching the SQUID to its nonzero dc voltage state. The readout scheme presented here allows for reading out multiple qubits using a single microwave line by employing frequency-division multiplexing.
We present experimental results on a dispersive scheme for reading out a Josephson phase qubit. A capacitively shunted dc-SQUID is used as a nonlinear resonator which is inductively coupled to the qubit. We detect the flux state of the qubit by measuring the amplitude and phase of a microwave pulse reflected from the SQUID resonator. By this low-dissipative method, we reduce the qubit state measurement time down to 25 microseconds, which is much faster than using the conventional readout performed by switching the SQUID to its non-zero dc voltage state. The demonstrated readout scheme allows for reading out multiple qubits using a single microwave line by employing frequency-division multiplexing.
Circuit quantum electrodynamics (cQED) is a prominent platform for quantum information processing, in which microwave photons are confined into resonant cavities coupled to superconducting quantum bits (qubits). The large effective dipole moment of the qubit, in combination with the high energy density of the quasi 1-D resonator allow these systems to enter the so-called strong coupling regime. The quantum state of the qubit can then be assessed by probing the frequency of the resonator, protecting the qubit from otherwise losing its energy to the environment. However, eventhough this so-called dispersive readout technique has proven useful, it is often in itself insufficient to render single-shot readout performance | one of the crucial tasks required for realizing a quantum computer. This thesis describes the demonstration of a single-shot readout technique forsuperconducting quantum bits, based on coupling the qubit to a frequency-tunable resonator. The backbone of our device is a 5 GHz quarter-wavelength coplanar waveguide resonator, terminated at one end by a non-linear inductance provided by a superconducting quantum interference device (SQUID). The SQUID acts as a flux-controlled boundary condition, which effectively changes the electrical length of the resonator. This enables the modulation of the resonant frequency by coupling microwave magnetic flux into the SQUID, using an on-chip transmission line. The modulation occurs on a timescale much faster than the photon loss out of the resonator and if the pump strength exceeds a threshold value set by the damping rate of the resonator, an intense photon field will build up inside the resonator | known as "parametric oscillations". By heterodyne detection of the output signal from the Josephson parametric oscillator (JPO), we first extracted two leading nonlinear effects of the system (dominating in different limits of applied magnetic flux). Next, we couple a qubit to the JPO and demonstrate that we can encode its quantum state onto the strong output field of the parametric oscillator (or lack thereof), rendering a signal-to-noise ratio sufficient for single-shot state detection and therefore also obviating a quantum limited parametric amplifier. The thesis also contains results from microscopic studies of the Josephson junctions, which we use to provide the necessary nonlinearities in the above mentioned devices. In particular, we show how the microstructure of the barrier layer and its atomic composition can be used to infer important electrical properties of the junctions. This knowledge allows us to better tailor the properties of Josephson-based devices.