Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconducting Hot Electron Bolometer Mixers for Submillimeter Receivers

Anders J. Skalare, William R. McGrath, Bruce Bumble, Henry George LeDuc, Peter John Burke, A. A. Verheijen, D. E. Prober

Published May 10, 1994• 0 citations
OpenAlex

Related papers

Superconducting Hot-Electron Bolometer Mixer for Terahertz Heterodyne Receivers

Alexei D. Semenov, Heinz‐Wilhelm Hübers, Heiko Richter +4 more

Softwaretechnik-Trends•Apr 1, 2003•1 citation

Terahertz heterodyne receivers based on superconductive hot-electron bolometer mixers

Matvey I. Finkel, S. N. Maslennikov, Gregory N Gol'tsman

Radiophysics and Quantum Electronics•Oct 1, 2005•2 citations

Recent progress in submillimeter heterodyne receiver development

Jonas Stasys Zmuidzinas

The progress made in relation to the development of sensitive submillimeter heterodyne receiver systems is reviewed. Sensitive superconductor-insulator-superconductor (SIS) tunnel junction mixers were demonstrated at frequencies of greater than 1 THz, with noise temperatures of below 1000 K. An alternative mixer technology is that of the superconducting hot electron bolometer, for which sensitivities of 1.2 THz and 2.5 THz were demonstrated. Local oscillator technology is under development. Gunn oscillators followed by Schottky varactor frequency multipliers have sufficient output power to drive SIS mixers at 1 THz. It is considered that optical photomixer local oscillators have potential for driving hot electron bolometers above 1 THz.

•Dec 1, 1996•3 citations

Comparison between hot spot modeling and measurement of a superconducting hot electron bolometer mixer at submillimeter wavelengths

Wei Miao, Y. Delorme, A. Féret +8 more

This paper presents the modeling and measurement of a quasioptical niobium nitride superconducting hot electron bolometer mixer at submillimeter wavelengths. The modeling is performed with a distributed hot spot model which is based on solving a heat balance equation for electron temperature along the superconducting microbridge. Particular care has been taken during the modeling concerning the temperature-dependent resistance and the bias current dependence of the critical temperature of the device. The dc and mixing characteristics of this mixer have been computed and we have observed a quite good match between the predicted and the measured results for both dc characteristics and mixing performances at submillimeter wavelengths.

Journal of Applied Physics•Nov 15, 2009•13 citations

Study of Mid-infrared Superconducting Hot Electron Bolometer Mixers

Akira Kawakami, Hisashi Shimakage, Junsei Horikawa +4 more

IEICE Technical Report; IEICE Tech. Rep.•Jan 12, 2017•0 citations

Membrane-based HEB mixer for THz applications

Jean Baubert, Morvan C. Salez, Y. Delorme +4 more

We report in this paper a new concept for 2.7 THz superconducting Niobium nitride (NbN) Hot-Electron Bolometer mixer (HEB). The membrane process was developped for space telecommnunication applications a few years ago and the HEB mixer concept is now considered as the best choice for low-noise submillimeter-wave frequency heterodyne receivers. The idea is then to join these two technologies. The novel fabrication scheme is to fabricate a NbN HEB mixer on a 1 μm thick stress-less Si3N4/SiO2 membrane. This seems to present numerous improvements concerning : use at higher RF frequencies, power coupling efficiency, HEB mixer sensitivity, noise temperature, and space applications. This work is to be continued within the framework of an ESA TRP project, a 2.7 THz heterodyne camera with numerous applications including a SOFIA airborne receiver. This paper presents the whole fabrication process, the validation tests and preliminary results. Membrane-based HEB mixer theory is currently being investigated and further tests such as heterodyne and Fourier transform spectrometry measurement are planed shortly.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 25, 2003•2 citations
The progress made in relation to the development of sensitive submillimeter heterodyne receiver systems is reviewed. Sensitive superconductor-insulator-superconductor (SIS) tunnel junction mixers were demonstrated at frequencies of greater than 1 THz, with noise temperatures of below 1000 K. An alternative mixer technology is that of the superconducting hot electron bolometer, for which sensitivities of 1.2 THz and 2.5 THz were demonstrated. Local oscillator technology is under development. Gunn oscillators followed by Schottky varactor frequency multipliers have sufficient output power to drive SIS mixers at 1 THz. It is considered that optical photomixer local oscillators have potential for driving hot electron bolometers above 1 THz.
This paper presents the modeling and measurement of a quasioptical niobium nitride superconducting hot electron bolometer mixer at submillimeter wavelengths. The modeling is performed with a distributed hot spot model which is based on solving a heat balance equation for electron temperature along the superconducting microbridge. Particular care has been taken during the modeling concerning the temperature-dependent resistance and the bias current dependence of the critical temperature of the device. The dc and mixing characteristics of this mixer have been computed and we have observed a quite good match between the predicted and the measured results for both dc characteristics and mixing performances at submillimeter wavelengths.
We report in this paper a new concept for 2.7 THz superconducting Niobium nitride (NbN) Hot-Electron Bolometer mixer (HEB). The membrane process was developped for space telecommnunication applications a few years ago and the HEB mixer concept is now considered as the best choice for low-noise submillimeter-wave frequency heterodyne receivers. The idea is then to join these two technologies. The novel fabrication scheme is to fabricate a NbN HEB mixer on a 1 μm thick stress-less Si3N4/SiO2 membrane. This seems to present numerous improvements concerning : use at higher RF frequencies, power coupling efficiency, HEB mixer sensitivity, noise temperature, and space applications. This work is to be continued within the framework of an ESA TRP project, a 2.7 THz heterodyne camera with numerous applications including a SOFIA airborne receiver. This paper presents the whole fabrication process, the validation tests and preliminary results. Membrane-based HEB mixer theory is currently being investigated and further tests such as heterodyne and Fourier transform spectrometry measurement are planed shortly.