Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

A millimeter unilateral finline SIS mixer with a wide IF bandwidth

Yangjun Zhou

Published Jan 1, 2013• 0 citations
Publisher

Abstract

Superconductor-Insulator-Superconductor (SIS) tunnel junction mixers are now commonly used in as- tronomical receivers at (sub)millimeter wavelengths because of their superb sensitivity, high dynamic range and stability of operation. Niobium SIS mixers operating at frequencies well below the super- conducting gap (∼680 GHz) have already achieved quantum limited sensitivity. Therefore to further enhance the receiver sensitivity, increasing the Intermediate Frequency (IF) bandwidth of SIS mixers has became crucial. This thesis focuses on the theoretical modeling, design and experimental verifi- cation of Nb SIS mixers operating around 230 GHz with a wide IF bandwidth of 1–15 GHz. These mixers were designed for a single baseline heterodyne interferometer (GUBBINS), which is being built to observe the Sunyaev-Zel’dovich effect in the Cosmic Microwave Background. The combination of wide IF bandwidth SIS mixers and complex analogue correlators will allow GUBBINS to feature high surface brightness sensitivity, that helps to distinguish the weak SZ effect from the background noise. The SIS mixer detector system was assembled inside the GUBBINS cryostat together with the IF electronics and RF/LO optical systems. Low noise temperatures of around 71 K were then measured in the GUBBINS system. The Nb SIS mixer we have developed uses a unilateral finline and fully integrated planar circuits deposited on a silicon substrate, to couple the electromagnetic radiation from the waveguide into the SIS junction. The finline mixer allows a broad-band RF coupling, an easy integration of the on-chip planar circuits and an easy-to-fabricate mixer block. To achieve a wide IF bandwidth, the output impedance of the SIS mixer was well matched to the input impedance of the amplifier by a multi-stage microstrip circuit. Additionally, the planar circuit of the SIS mixer was also designed to have a small lumped inductance and capacitance. The SIS mixer chip was extensively simulated by rigorous electromagnetic software (HFSS) and the S-parameter was exported to a quantum mixing package SuperMix to produce a full-wave model of the mixer. Experimental testing yielded a best noise temperature of 50 K with an average noise temperature of 75 K over an RF bandwidth of 160 GHz– 260 GHz. We have performed thorough experimental and computational investigation of the IF system in particular the constraints on the bandwidth caused by the lumped element capacitance of the mixer chip and the matching of the output impedance of the mixer to the IF amplifier. Our conclusion is that a bandwidth of 1–15 GHz could be achieved using our mixer design, subject to the performance of the amplifier. Finally, a variable temperature load system was successfully developed and tested inside the cryostat, to avoid the losses from the room-temperature optics. We have showed that the noise temperature of the SIS detector could be reduced by as much as 15 K by testing the mixer using a variable temperature load inside the cryostat.

DOI
10.5287/ora-or6ane9jk

Related papers

A 220 GHz finline mixer with ultra-wide instantaneous bandwidth

BK Tan, Faouzi M. Boussaha, Christine Chaumont +1 more

We describe the design and fabrication of a 220 GHz superconductor-insulator-superconductor (SIS) mixer with ultrawide IF bandwidth. The mixer is fabricated on a 100 µm thick quartz substrate, with planar circuit on-chip integration. The RF power is coupled to the tunnel junction via a unilateral finline taper and a slotline-to-microstrip transition. We used a double-stub tuning network to tune out the junction’s parasitic capacitance at a broad RF bandwidth, and matched the output impedance of the mixer to the input impedance of the IF amplifier (50 Ω) from 4–18 GHz using a 6-stage IF impedance-transformer. We have fabricated these devices and have measured good DC current-voltage (IV) characteristic curves. The heterodyne mixing performance of these devices is currently being measured, and we expect to present the results in the forthcoming ISSTT conference in March.

ORA review team•Jan 1, 2015•7 citations

Low-noise THz Niobium SIS Mixers

Mei Bin

This thesis describes the development of low-noise heterodyne receivers at THz frequencies for submillimeter astronomy using Nb-based superconductor-insulator-superconductor (SIS) tunneling junctions. The mixers utilize a quasi-optical configuration which consists of a planar twin-slot antenna and antisymmetrically-fed two-junctions on an antireflection-coated silicon hyperhemispherical lens. On-chip integrated tuning circuits, in the form of microstrip lines, are used to obtain maximum coupling efficiency in the designed frequency band. To reduce the rf losses in the integrated tuning circuits above the superconducting Nb gap frequency (~ 700 GHz), normal-metal Al is used to replace Nb as the tuning circuits. To account the rf losses in the micros trip lines, we calculated the surface impedance of the AI films using the nonlocal anomalous skin effect for finite thickness films. Nb films were calculated using the Mattis-Bardeen theory in the extreme anomalous limit. Our calculations show that the losses of the Al and Nb microstrip lines are about equal at 830 GHz. For Al-wiring and Nb-wiring mixers both optimized at 1050 GHz, the RF coupling efficiency of Al-wiring mixer is higher than that of Nb-wiring one by almost 50%. We have designed both Nb-wiring and Al-wiring mixers below and above the gap frequency. A Fourier transform spectrometer (FTS) has been constructed especially for the study of the frequency response of SIS receivers. This FTS features large aperture size (10 inch) and high frequency resolution (114 MHz). The FTS spectra, obtained using the SIS receivers as direct detectors on the FTS, agree quite well with our theoretical simulations. We have also, for the first time, measured the FTS heterodyne response of an SIS mixer at sufficiently high resolution to resolve the LO and the sidebands. Heterodyne measurements of our SIS receivers with Nb-wiring or Al-wiring have yielded results which arc among the best reported to date for broadband heterodyne receivers. The Nb-wiring mixers, covering 400 - 850 GHz band with four separate fixed-tuned mixers, have uncorrected DSB receiver noise temperature around 5hv/kb to 700 GHz, and better than 540 K at 808 GHz. An Al-wiring mixer designed for 1050 GHz band has an uncorrected DSB receiver noise temperature 840 K at 1042 GHz and 2.5 K bath temperature. Mixer performance analysis shows that Nb junctions can work well up to twice the gap frequency and the major cause of loss above the gap frequency is the rf losses in the microstrip tuning structures. Further advances in THz SIS mixers may be possible using circuits fabricated with higher-gap superconductors such as NbN. However, this will require high-quality films with low RF surface resistance at THz frequencies.

•Sep 1, 1997•8 citations

Wide If 230-GHz Superconductor-Insulator-Superconductor Mixer

Naeun Shin, Jung‐Won Lee, Ming-Jye Wang

A 230 GHz Superconductor-Insulator-Superconductor (SIS) mixer is designed focusing on a good performance in the IF frequency range of 4–16 GHz over the RF band from 211 to 275 GHz. A transition from a full-height waveguide to a probe is designed using HFSS. The mixer chips containing SIS junctions are designed and optimized to have low total capacitance of circuits to ensure wide IF bandwidth. The chip fabrication was done in Academia Sinica Institute of Astronomy and Astrophysics (ASIAA), where the masks were conducted by TSMC. A lab test was conducted on a superconducting mixer with a cryogenic dewar. The gap voltage in the I-V curve of the mixer is approximately 8 mV, and there is a clear nonlinearity around a current of 110 μA, which matches well with the simulation. The receiver noise temperature is approximately 60 K including optical losses and the noise from the RF input.

International Conference on Information and Communication Technology Convergence (ICTC)•Oct 16, 2024•1 citation

Analyzing and improving the IF bandwidth performance for 345 GHz SIS mixer

Chen Peng, Boxun Wang, Liping Zuo +5 more

Abstract The wide intermediate frequency (IF) bandwidth is a core performance metric for terahertz heterodyne receivers, and a wide-IF superconductor–insulator–superconductor (SIS) mixer is key to achieving this. This paper presents the simulation-based design, optimization, and performance analysis of a 345 GHz superconducting SIS mixer developed for wide-IF applications. The mixer employs a parallel-connected twin-junction tuning structure and integrates a dedicated IF impedance matching circuit, achieving wideband impedance matching between the mixer output port and low-noise amplifier. The design is based on two tunnel junction technologies, AlO x and AlN, with critical current densities of 1 kA·cm −2 and 25 kA·cm −2 , respectively. We systematically studied the effects of different junction materials and junction areas on the RF and IF bandwidth performance of the SIS mixer. It is found that for AlN-barrier junctions with diameters of 0.6 μ m and 0.8 μ m, the receiver’s IF noise temperature slowly decreased as the IF frequency increased at a high local oscillator frequency. Furthermore, we incorporated the calculated IF output port impedance into the mixer model for correction and introduced an integrated IF circuit approach, overcoming the original IF bandwidth limitation. Simulations show that the newly designed mixer achieves the stringent sensitivity and bandwidth requirements across the 320–370 GHz range, delivering an IF bandwidth of 4–22 GHz and a receiver noise temperature of 39–73 K. Notably, the −3 dB IF bandwidth is improved by more than 1.5 times compared to conventional AlO x -based designs. These findings provide new design guidelines and quantitative criteria for next-generation wide-IF receivers and other high-frequency applications requiring a wide IF bandwidth.

Journal of Physics D Applied Physics•Oct 6, 2026•0 citations

A 650 GHz Unilateral Finline SIS Mixer Fed by a Multiple Flare-Angle Smooth-Walled Horn

Boon-Kok Tan, G. Yassin, Paul Grimes +3 more

We report the design and successful operation of an superconductor-insulator-superconductor (SIS) mixer operating near the superconducting gap of niobium. A key feature of this design is the employment of a unilateral finline taper to transform the waveguide modes to microstrip signals. This transition is easy to design since it can be rigorously modeled, and also easy to fabricate being a single-layer structure. We will show that unilateral finline mixers have important advantages at THz frequencies since they exhibit wideband operation at both radio frequency (RF) and intermediate frequency (IF), allow elegant on-chip integration of the mixer circuits and result in an extremely simple mixer block that does not require a backshort or any mechanical tuners. The mixer we describe below is fed by a multiple flare-angle smooth-walled horn which exhibits beam pattern characteristic comparable to the conventional corrugated horn and yet is much easier to fabricate. In this paper, we shall present a brief discussion of the testing of the multiple flare-angle horn and detailed description of the design and testing of the mixer, covering ~100 GHz bandwidth centered at 650 GHz. In particular, we will present full electromagnetic de sign description of the mixer chip including the superconducting effects, and the heterodyne properties of the mixer using quantum mixing theory. Mixer performance tests that we carried out from 595 to 702 GHz gave a best receiver noise temperature of 145 K at 600 GHz, corrected for a 75 μm beam splitter. Finally, we performed a thorough analysis of the mixer performance, comparing the experimental results with theoretical models. Our investigation demonstrated that unilateral finline mixers fed by a multiple flare-angle horn can yield performance comparable to conventional designs, hence are suitable for large format mixer array at THz frequencies.

IEEE Transactions on Terahertz Science and Technology•Dec 13, 2011•17 citations

Series-connected array of superconductor–insulator–superconductor junctions in the 100 GHz-band heterodyne mixer for FOREST on the Nobeyama 45 m telescope

Taku Nakajima, Hirofumi Inoue, Yumi Fujii +5 more

Abstract We have designed and experimentally evaluated a series-connected array of superconductor–insulator–superconductor (SIS) junctions in the 100 GHz-band mixer for the multi-beam receiver FOREST on the Nobeyama 45 m millimeter-wave telescope. The construction of the junction chip comprised a waveguide probe antenna, impedance-matching circuit, SIS array junction, and choke filter, which were made from a superconducting niobium planar circuit on a quartz substrate. The multi-stage impedance-matching circuit between the feed point and the SIS junction was designed as a capacitively loaded transmission line, and it comprised two sections with high (∼90 Ω) and low (∼10 Ω) characteristic impedance transmission lines. The structure of this tuning line was simple and easy to fabricate, and the feed impedance matched with the SIS junction in a wide frequency range. The signal coupling efficiency was more than 92% and the expected receiver noise temperature was approximately twice the quantum limit for 75–125 GHz based on quantum theory. The array junction devices with three to six connected junctions were fabricated and we measured their performance in terms of the receiver noise temperature and gain compression in the laboratory. We successfully developed an array junction device with a receiver noise temperature of ∼15–30 K and confirmed that the improvement in the saturation power corresponded to the number of junctions. The newly developed array junction mixer was installed in the FOREST receiver and it successfully detected the 12CO(J = 1–0) molecular line toward IRC +10216 with the Nobeyama 45 m telescope.

arXiv:1809.02304•Publications of the Astronomical Society of Japan•Sep 13, 2018•10 citations
Superconductor-Insulator-Superconductor (SIS) tunnel junction mixers are now commonly used in as- tronomical receivers at (sub)millimeter wavelengths because of their superb sensitivity, high dynamic range and stability of operation. Niobium SIS mixers operating at frequencies well below the super- conducting gap (∼680 GHz) have already achieved quantum limited sensitivity. Therefore to further enhance the receiver sensitivity, increasing the Intermediate Frequency (IF) bandwidth of SIS mixers has became crucial. This thesis focuses on the theoretical modeling, design and experimental verifi- cation of Nb SIS mixers operating around 230 GHz with a wide IF bandwidth of 1–15 GHz. These mixers were designed for a single baseline heterodyne interferometer (GUBBINS), which is being built to observe the Sunyaev-Zel’dovich effect in the Cosmic Microwave Background. The combination of wide IF bandwidth SIS mixers and complex analogue correlators will allow GUBBINS to feature high surface brightness sensitivity, that helps to distinguish the weak SZ effect from the background noise. The SIS mixer detector system was assembled inside the GUBBINS cryostat together with the IF electronics and RF/LO optical systems. Low noise temperatures of around 71 K were then measured in the GUBBINS system. The Nb SIS mixer we have developed uses a unilateral finline and fully integrated planar circuits deposited on a silicon substrate, to couple the electromagnetic radiation from the waveguide into the SIS junction. The finline mixer allows a broad-band RF coupling, an easy integration of the on-chip planar circuits and an easy-to-fabricate mixer block. To achieve a wide IF bandwidth, the output impedance of the SIS mixer was well matched to the input impedance of the amplifier by a multi-stage microstrip circuit. Additionally, the planar circuit of the SIS mixer was also designed to have a small lumped inductance and capacitance. The SIS mixer chip was extensively simulated by rigorous electromagnetic software (HFSS) and the S-parameter was exported to a quantum mixing package SuperMix to produce a full-wave model of the mixer. Experimental testing yielded a best noise temperature of 50 K with an average noise temperature of 75 K over an RF bandwidth of 160 GHz– 260 GHz. We have performed thorough experimental and computational investigation of the IF system in particular the constraints on the bandwidth caused by the lumped element capacitance of the mixer chip and the matching of the output impedance of the mixer to the IF amplifier. Our conclusion is that a bandwidth of 1–15 GHz could be achieved using our mixer design, subject to the performance of the amplifier. Finally, a variable temperature load system was successfully developed and tested inside the cryostat, to avoid the losses from the room-temperature optics. We have showed that the noise temperature of the SIS detector could be reduced by as much as 15 K by testing the mixer using a variable temperature load inside the cryostat.
We describe the design and fabrication of a 220 GHz superconductor-insulator-superconductor (SIS) mixer with ultrawide IF bandwidth. The mixer is fabricated on a 100 µm thick quartz substrate, with planar circuit on-chip integration. The RF power is coupled to the tunnel junction via a unilateral finline taper and a slotline-to-microstrip transition. We used a double-stub tuning network to tune out the junction’s parasitic capacitance at a broad RF bandwidth, and matched the output impedance of the mixer to the input impedance of the IF amplifier (50 Ω) from 4–18 GHz using a 6-stage IF impedance-transformer. We have fabricated these devices and have measured good DC current-voltage (IV) characteristic curves. The heterodyne mixing performance of these devices is currently being measured, and we expect to present the results in the forthcoming ISSTT conference in March.
This thesis describes the development of low-noise heterodyne receivers at THz frequencies for submillimeter astronomy using Nb-based superconductor-insulator-superconductor (SIS) tunneling junctions. The mixers utilize a quasi-optical configuration which consists of a planar twin-slot antenna and antisymmetrically-fed two-junctions on an antireflection-coated silicon hyperhemispherical lens. On-chip integrated tuning circuits, in the form of microstrip lines, are used to obtain maximum coupling efficiency in the designed frequency band. To reduce the rf losses in the integrated tuning circuits above the superconducting Nb gap frequency (~ 700 GHz), normal-metal Al is used to replace Nb as the tuning circuits. To account the rf losses in the micros trip lines, we calculated the surface impedance of the AI films using the nonlocal anomalous skin effect for finite thickness films. Nb films were calculated using the Mattis-Bardeen theory in the extreme anomalous limit. Our calculations show that the losses of the Al and Nb microstrip lines are about equal at 830 GHz. For Al-wiring and Nb-wiring mixers both optimized at 1050 GHz, the RF coupling efficiency of Al-wiring mixer is higher than that of Nb-wiring one by almost 50%. We have designed both Nb-wiring and Al-wiring mixers below and above the gap frequency. A Fourier transform spectrometer (FTS) has been constructed especially for the study of the frequency response of SIS receivers. This FTS features large aperture size (10 inch) and high frequency resolution (114 MHz). The FTS spectra, obtained using the SIS receivers as direct detectors on the FTS, agree quite well with our theoretical simulations. We have also, for the first time, measured the FTS heterodyne response of an SIS mixer at sufficiently high resolution to resolve the LO and the sidebands. Heterodyne measurements of our SIS receivers with Nb-wiring or Al-wiring have yielded results which arc among the best reported to date for broadband heterodyne receivers. The Nb-wiring mixers, covering 400 - 850 GHz band with four separate fixed-tuned mixers, have uncorrected DSB receiver noise temperature around 5hv/kb to 700 GHz, and better than 540 K at 808 GHz. An Al-wiring mixer designed for 1050 GHz band has an uncorrected DSB receiver noise temperature 840 K at 1042 GHz and 2.5 K bath temperature. Mixer performance analysis shows that Nb junctions can work well up to twice the gap frequency and the major cause of loss above the gap frequency is the rf losses in the microstrip tuning structures. Further advances in THz SIS mixers may be possible using circuits fabricated with higher-gap superconductors such as NbN. However, this will require high-quality films with low RF surface resistance at THz frequencies.
A 230 GHz Superconductor-Insulator-Superconductor (SIS) mixer is designed focusing on a good performance in the IF frequency range of 4–16 GHz over the RF band from 211 to 275 GHz. A transition from a full-height waveguide to a probe is designed using HFSS. The mixer chips containing SIS junctions are designed and optimized to have low total capacitance of circuits to ensure wide IF bandwidth. The chip fabrication was done in Academia Sinica Institute of Astronomy and Astrophysics (ASIAA), where the masks were conducted by TSMC. A lab test was conducted on a superconducting mixer with a cryogenic dewar. The gap voltage in the I-V curve of the mixer is approximately 8 mV, and there is a clear nonlinearity around a current of 110 μA, which matches well with the simulation. The receiver noise temperature is approximately 60 K including optical losses and the noise from the RF input.
Abstract The wide intermediate frequency (IF) bandwidth is a core performance metric for terahertz heterodyne receivers, and a wide-IF superconductor–insulator–superconductor (SIS) mixer is key to achieving this. This paper presents the simulation-based design, optimization, and performance analysis of a 345 GHz superconducting SIS mixer developed for wide-IF applications. The mixer employs a parallel-connected twin-junction tuning structure and integrates a dedicated IF impedance matching circuit, achieving wideband impedance matching between the mixer output port and low-noise amplifier. The design is based on two tunnel junction technologies, AlO x and AlN, with critical current densities of 1 kA·cm −2 and 25 kA·cm −2 , respectively. We systematically studied the effects of different junction materials and junction areas on the RF and IF bandwidth performance of the SIS mixer. It is found that for AlN-barrier junctions with diameters of 0.6 μ m and 0.8 μ m, the receiver’s IF noise temperature slowly decreased as the IF frequency increased at a high local oscillator frequency. Furthermore, we incorporated the calculated IF output port impedance into the mixer model for correction and introduced an integrated IF circuit approach, overcoming the original IF bandwidth limitation. Simulations show that the newly designed mixer achieves the stringent sensitivity and bandwidth requirements across the 320–370 GHz range, delivering an IF bandwidth of 4–22 GHz and a receiver noise temperature of 39–73 K. Notably, the −3 dB IF bandwidth is improved by more than 1.5 times compared to conventional AlO x -based designs. These findings provide new design guidelines and quantitative criteria for next-generation wide-IF receivers and other high-frequency applications requiring a wide IF bandwidth.
We report the design and successful operation of an superconductor-insulator-superconductor (SIS) mixer operating near the superconducting gap of niobium. A key feature of this design is the employment of a unilateral finline taper to transform the waveguide modes to microstrip signals. This transition is easy to design since it can be rigorously modeled, and also easy to fabricate being a single-layer structure. We will show that unilateral finline mixers have important advantages at THz frequencies since they exhibit wideband operation at both radio frequency (RF) and intermediate frequency (IF), allow elegant on-chip integration of the mixer circuits and result in an extremely simple mixer block that does not require a backshort or any mechanical tuners. The mixer we describe below is fed by a multiple flare-angle smooth-walled horn which exhibits beam pattern characteristic comparable to the conventional corrugated horn and yet is much easier to fabricate. In this paper, we shall present a brief discussion of the testing of the multiple flare-angle horn and detailed description of the design and testing of the mixer, covering ~100 GHz bandwidth centered at 650 GHz. In particular, we will present full electromagnetic de sign description of the mixer chip including the superconducting effects, and the heterodyne properties of the mixer using quantum mixing theory. Mixer performance tests that we carried out from 595 to 702 GHz gave a best receiver noise temperature of 145 K at 600 GHz, corrected for a 75 μm beam splitter. Finally, we performed a thorough analysis of the mixer performance, comparing the experimental results with theoretical models. Our investigation demonstrated that unilateral finline mixers fed by a multiple flare-angle horn can yield performance comparable to conventional designs, hence are suitable for large format mixer array at THz frequencies.
Abstract We have designed and experimentally evaluated a series-connected array of superconductor–insulator–superconductor (SIS) junctions in the 100 GHz-band mixer for the multi-beam receiver FOREST on the Nobeyama 45 m millimeter-wave telescope. The construction of the junction chip comprised a waveguide probe antenna, impedance-matching circuit, SIS array junction, and choke filter, which were made from a superconducting niobium planar circuit on a quartz substrate. The multi-stage impedance-matching circuit between the feed point and the SIS junction was designed as a capacitively loaded transmission line, and it comprised two sections with high (∼90 Ω) and low (∼10 Ω) characteristic impedance transmission lines. The structure of this tuning line was simple and easy to fabricate, and the feed impedance matched with the SIS junction in a wide frequency range. The signal coupling efficiency was more than 92% and the expected receiver noise temperature was approximately twice the quantum limit for 75–125 GHz based on quantum theory. The array junction devices with three to six connected junctions were fabricated and we measured their performance in terms of the receiver noise temperature and gain compression in the laboratory. We successfully developed an array junction device with a receiver noise temperature of ∼15–30 K and confirmed that the improvement in the saturation power corresponded to the number of junctions. The newly developed array junction mixer was installed in the FOREST receiver and it successfully detected the 12CO(J = 1–0) molecular line toward IRC +10216 with the Nobeyama 45 m telescope.