Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Ring Resonator Size, Loss and Photon Lifetime for an Integrated Heralding Circuit

William Alexander Aldred

Published Nov 12, 2026• 1 citation
Publisher

Abstract

On a photonic chip, a ring resonator stores light for a time set by its circumference and its propagation loss. That storage time, together with the free spectral range, decides whether the ring can act as a filter, a delay, or a photon-pair source enhancement. This study computes the quantities that follow from stated assumptions for silicon nitride waveguide rings, group index 2.0, wavelength 1550 nm, propagation loss 0.1, 0.5 and 1.0 dB per centimetre, using the relations set out in the Methods. The headline results are Q at 0.1 dBcm = 3.521e+06, lifetime at 0.1 dBcm s = 2.897e-09, Q at 1 dBcm = 3.521e+05, lifetime at 1 dBcm s = 2.897e-10, FSR at 100 um Hz = 2.386e+11. The central question is stated as follows: For silicon nitride rings of radius 20 to 200 micrometres with stated propagation losses, what quality factor, photon lifetime and free spectral range follow, and which combination reaches a lifetime of one nanosecond? The answer obtained here is conditional on the assumptions listed in the paper and in the deposited calculation; changing an assumption changes the numbers in the way the sensitivity discussion describes. Integrated rings are reported with quality factors from ten thousand to above ten million depending on material and loss, so the computed table spans the practical interval. The work is a computation, not a laboratory measurement, and it is labelled accordingly. Where the computed result is unfavourable to the device or effect under study, that outcome is reported in the same terms as a favourable one, because a bound that only appears when it is welcome is not a bound at all. All numerical statements in this abstract are reproduced by the deposited script from the stated inputs.

DOI
10.5281/zenodo.24159700

Related papers

Design Blueprint: Ring Resonator Size, Loss and Photon Lifetime for an Integrated Heralding Circuit

William Alexander Aldred

Design blueprint derived from the source paper (DOI 10.5281/zenodo.24159701): On a photonic chip, a ring resonator stores light for a time set by its circumference and its propagation loss. That storage time, together with the free spectral range, decides whether the ring can act as a filter, a delay, or a photon-pair source enhancement. This study computes the quantities that follow from stated assumptions for silicon nitride waveguide rings, group index 2.0, wavelength 1550 nm, propagation loss 0.1, 0.5 and 1.0 dB per centimetre, using the relations set out in the Methods. The headline results are Q at 0.1 dBcm = 3.521e+06, lifetime at 0.1 dBcm s = 2.897e-09, Q at 1 dBcm = 3.521e+05, lifetime at 1 dBcm s = 2.897e-10, FSR at 100 um Hz = 2.386e+11. The central question is stated as follows: For silicon nitride rings of radius 20 to 200 micrometres with stated propagation losses, what quality factor, photon lifetime and free spectral range follow, and which combination reaches a lifetime of one nanosecond? The answer obtained here is conditional on the assumptions listed in the paper and in the deposited calculation; changing an assumption changes the numbers in the way the sensitivity discussion describes. Integrated rings are reported with quality factors from ten thousand to above ten million depending on material and loss, so the computed table spans the practical interval. The work is a computation, not a laboratory measurement, and it is labelled accordingly. Where the computed result is unfavourable to the device or effect under study, that outcome is reported in the same terms as a favourable one, because a bound that only appears when it is welcome is not a bound at all. All numerical statements in this abstract are reproduced by the deposited script from the stated inputs. Status: DESIGN BLUEPRINT — SIMULATED, NOT MEASURED — NOT BUILT. All numbers are simulated values from the source paper's computation, deposited with this blueprint as compute.py and results.json. AI-use disclosure: Dave, an AI research system, assisted with the computation and drafting under the author's direction; author of record William Alexander Aldred.

•Nov 12, 2026•0 citations

Mirror Reflectivity and Photon Storage Time in a Fabry-Perot Cavity for Single Photons

William Alexander Aldred

A single photon that enters a Fabry-Perot resonator leaves again after a dwell time set by how often it reflects and how much light escapes at each reflection. That dwell time decides whether the photon can be held long enough for a control operation, a heralding check, or a synchronisation delay, and it also sets the spectral width the source must match. This study computes the quantities that follow from stated assumptions for a symmetric two-mirror Fabry-Perot cavity of length 0.05 m, wavelength 780 nm, with a fixed additional round-trip loss of 0.002 in intensity, using the relations set out in the Methods. The headline results are finesse at R 0.99 = 260.7, lifetime at R 0.99 s = 1.384e-08, linewidth at R 0.99 Hz = 1.150e+07, finesse at R 0.9995 = 1.256e+03, lifetime at R 0.9995 s = 6.666e-08. Further computed values are saturation ratio lifetime = 4.817. The central question is stated as follows: How much storage time, spectral width and round-trip loss follow from a stated mirror reflectivity for a five-centimetre resonator at 780 nm, and at what reflectivity does further coating improvement stop buying useful time because other losses dominate? The answer obtained here is conditional on the assumptions listed in the paper and in the deposited calculation; changing an assumption changes the numbers in the way the sensitivity discussion describes. Laboratory resonators of this size are commonly quoted with finesse values from a few hundred for coated optics to well above one hundred thousand for supermirror coatings, so a sweep across that interval tests both ordinary and demanding coatings. The work is a computation, not a laboratory measurement, and it is labelled accordingly. Where the computed result is unfavourable to the device or effect under study, that outcome is reported in the same terms as a favourable one, because a bound that only appears when it is welcome is not a bound at all. All numerical statements in this abstract are reproduced by the deposited script from the stated inputs.

•Nov 12, 2026•0 citations

Efficiently heralded silicon ring resonator photon-pair source

Jeffrey A. Steidle, Michael L. Fanto, Christopher C. Tison +3 more

Presented here are results on a silicon ring resonator photon pair source with a high heralding efficiency. Previous ring resonator sources suffered from an effective 50% loss because, in order to generate the photons, the pump must be able to couple into the resonator which is an effective loss channel. However, in practice the optical loss of the pump can be traded off for a dramatic increase in heralding efficiency. This research found theoretically that the heralding efficiency should increase by a factor of ∼ 3:75 with a factor of 10 increase in the required pump power. This was demonstrated experimentally by varying the separation (gap) between the input waveguide and the ring while maintaining a constant drop port gap. The ring (R = 18:5μm, W = 500nm, and H = 220nm) was pumped by a tunable laser (λ ≈ 1550nm). The non-degenerate photons, produced via spontaneous four wave mixing, exited the ring and were coupled to fiber upon which they were filtered symmetrically about the pump. Coincidence counts were collected for all possible photon path combinations (through and drop port) and the ratio of the drop port coincidences to the sum of the drop port and cross term coincidences (one photon from the drop port and one from the through port) was calculated. With a 350nm pump waveguide gap (2:33 times larger than the drop port gap) we confirmed our theoretical predictions, with an observed improvement in heralding efficiency by a factor of ∼ 2:61 (96:7% of correlated photons coupled out of the drop port). These results will enable increased photon flux integrated photon sources which can be utilized for high performance quantum computing and communication systems.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•May 19, 2016•3 citations

Development of a High Performance Resonant Photon-Pair Source in Silicon

Jeffrey A. Steidle

One of the key building blocks of quantum photonic systems is a source of indistinguishable photons. Silicon ring resonators can be used as photon pair sources by taking advantage of silicon's large third order nonlinearity with a process known as spontaneous four wave mixing. These sources are capable of producing pairs of indistinguishable photons but typically suffer from an effective 50% loss. By slightly decoupling the input waveguide from the ring, the desired photons generated in the ring can be directed to the drop port. Thus, the ratio between the coincidences from the drop port and the total number of coincidences from all ports (coincidence efficiency) can be significantly increased, with the trade-off being that the pump is less efficiently coupled into the ring. This asymmetric coupling scheme was used to demonstrate a dual-bus microring source with a coincidence efficiency of ~96%. Unfortunately, the penalty to pump power was quite large, with a required ~10x increase in the pump power to maintain the same pair generation rate.\nTo further improve upon this result, a microring source was designed with multipoint evanescent couplers to induce a strong spectral dependence in the coupling coefficients. This coupler design can be used on both sides of the ring resonator so that resonances supported by one of the couplers are suppressed by the other. This is the ideal configuration for a ring-based photon-pair source as it can only support the pump photons at the input side while only allowing the generated photons to leave through the output side. Asymmetric coupling was also used in this configuration but in a different way than in the previous source. In this case, the input side of the ring was configured to be critically coupled for maximal resonance enhancement while the output side was configured to be over coupled to minimize photon-pair loss within the ring. This device design was used to demonstrate a photon-pair source with coincidence efficiencies of 0.9981+-6.425x10^-4 and 0.9979+-1.665x10^-3 for degenerate and non-degenerate pump configuration respectively.\nIn addition to the source development, work was done to move some of the pump rejection filtering onto the photonic chip. While the fabricated device only exhibited an extinction of 50 dB, the root cause of the limited extinction was explored and a new filter design was proposed to overcome these limitations. With the combination of the microring source with its greatly improved efficiency and the movement toward reducing the required off-chip filtering, this work represents a significant advancement in the scalability of integrated quantum photonic systems which can enable high performance quantum computing and communication systems.

•Jan 1, 2019•0 citations

Twin-photon generation in a silicon nitride microresonator

Franz Pacher, Haochen Yan, Alekhya Ghosh +8 more

Photonic chips with silicon nitride ($\mathrm{Si_3N_4}$) microring resonators are well established as heralded single-photon sources, but their operation as frequency-degenerate twin-photon sources has not previously been demonstrated. Here, we realise a twin-photon source at telecommunication wavelengths in a $\mathrm{Si_3N_4}$ ring microresonator via an inverse four-wave mixing (FWM) process, in which two photons from spectrally distinct pumps are converted into a pair of identical twin photons. The measurements show a maximum coincidence-to-accidental ratio (CAR) of $5.4\pm0.6$. In addition, the microresonator functions as a heralded single-photon source through pump-degenerate spontaneous four-wave mixing (SFWM), exhibiting a spectral purity of $P=0.67\pm0.05$ and a heralded anti-bunching of $g^{(2)}_h(0)=0.0042\pm0.0015$. Together, these results demonstrate both photon-generation schemes on a single integrated $\mathrm{Si_3N_4}$ platform, highlighting its potential for scalable, tailored quantum light generation.

physics.opticsCross-listedarXiv:2609.04171•Sep 4, 2026•1 citation

Integrated photon sources for quantum information science applications

Paul M. Alsing, Dirk Robert Englund, Neville A. Mogent +8 more

Ring resonators are used as photon pair sources by taking advantage of the materials second or third order non- linearities through the processes of spontaneous parametric downconversion and spontaneous four wave mixing respectively. Two materials of interest for these applications are silicon for the infrared and aluminum nitride for the ultraviolet through the infrared. When fabricated into ring type sources they are capable of producing pairs of indistinguishable photons but typically suffer from an effective 50% loss. By slightly decoupling the input waveguide from the ring, the drop port coincidence ratio can be significantly increased with the trade-off being that the pump is less efficiently coupled into the ring. Ring resonators with this design have been demonstrated having coincidence ratios of 96% but requiring a factor of ~10 increase in the pump power. Through the modification of the coupling design that relies on additional spectral dependence, it is possible to achieve similar coincidence ratios without the increased pumping requirement. This can be achieved by coupling the input waveguide to the ring multiple times, thus creating a Mach-Zehnder interferometer. This coupler design can be used on both sides of the ring resonator so that resonances supported by one of the couplers are suppressed by the other. This is the ideal configuration for a photon-pair source as it can only support the pump photons at the input side while only allowing the generated photons to leave through the output side. Recently, this device has been realized with preliminary results exhibiting the desired spectral dependence and with a coincidence ratio as high as ~ 97% while allowing the pump to be nearly critically coupled to the ring. The demonstrated near unity coincidence ratio infers a near maximal heralding efficiency from the fabricated device. This device has the potential to greatly improve the scalability and performance of quantum computing and communication systems.

•Oct 5, 2017•1 citation
On a photonic chip, a ring resonator stores light for a time set by its circumference and its propagation loss. That storage time, together with the free spectral range, decides whether the ring can act as a filter, a delay, or a photon-pair source enhancement. This study computes the quantities that follow from stated assumptions for silicon nitride waveguide rings, group index 2.0, wavelength 1550 nm, propagation loss 0.1, 0.5 and 1.0 dB per centimetre, using the relations set out in the Methods. The headline results are Q at 0.1 dBcm = 3.521e+06, lifetime at 0.1 dBcm s = 2.897e-09, Q at 1 dBcm = 3.521e+05, lifetime at 1 dBcm s = 2.897e-10, FSR at 100 um Hz = 2.386e+11. The central question is stated as follows: For silicon nitride rings of radius 20 to 200 micrometres with stated propagation losses, what quality factor, photon lifetime and free spectral range follow, and which combination reaches a lifetime of one nanosecond? The answer obtained here is conditional on the assumptions listed in the paper and in the deposited calculation; changing an assumption changes the numbers in the way the sensitivity discussion describes. Integrated rings are reported with quality factors from ten thousand to above ten million depending on material and loss, so the computed table spans the practical interval. The work is a computation, not a laboratory measurement, and it is labelled accordingly. Where the computed result is unfavourable to the device or effect under study, that outcome is reported in the same terms as a favourable one, because a bound that only appears when it is welcome is not a bound at all. All numerical statements in this abstract are reproduced by the deposited script from the stated inputs.
Design blueprint derived from the source paper (DOI 10.5281/zenodo.24159701): On a photonic chip, a ring resonator stores light for a time set by its circumference and its propagation loss. That storage time, together with the free spectral range, decides whether the ring can act as a filter, a delay, or a photon-pair source enhancement. This study computes the quantities that follow from stated assumptions for silicon nitride waveguide rings, group index 2.0, wavelength 1550 nm, propagation loss 0.1, 0.5 and 1.0 dB per centimetre, using the relations set out in the Methods. The headline results are Q at 0.1 dBcm = 3.521e+06, lifetime at 0.1 dBcm s = 2.897e-09, Q at 1 dBcm = 3.521e+05, lifetime at 1 dBcm s = 2.897e-10, FSR at 100 um Hz = 2.386e+11. The central question is stated as follows: For silicon nitride rings of radius 20 to 200 micrometres with stated propagation losses, what quality factor, photon lifetime and free spectral range follow, and which combination reaches a lifetime of one nanosecond? The answer obtained here is conditional on the assumptions listed in the paper and in the deposited calculation; changing an assumption changes the numbers in the way the sensitivity discussion describes. Integrated rings are reported with quality factors from ten thousand to above ten million depending on material and loss, so the computed table spans the practical interval. The work is a computation, not a laboratory measurement, and it is labelled accordingly. Where the computed result is unfavourable to the device or effect under study, that outcome is reported in the same terms as a favourable one, because a bound that only appears when it is welcome is not a bound at all. All numerical statements in this abstract are reproduced by the deposited script from the stated inputs. Status: DESIGN BLUEPRINT — SIMULATED, NOT MEASURED — NOT BUILT. All numbers are simulated values from the source paper's computation, deposited with this blueprint as compute.py and results.json. AI-use disclosure: Dave, an AI research system, assisted with the computation and drafting under the author's direction; author of record William Alexander Aldred.
A single photon that enters a Fabry-Perot resonator leaves again after a dwell time set by how often it reflects and how much light escapes at each reflection. That dwell time decides whether the photon can be held long enough for a control operation, a heralding check, or a synchronisation delay, and it also sets the spectral width the source must match. This study computes the quantities that follow from stated assumptions for a symmetric two-mirror Fabry-Perot cavity of length 0.05 m, wavelength 780 nm, with a fixed additional round-trip loss of 0.002 in intensity, using the relations set out in the Methods. The headline results are finesse at R 0.99 = 260.7, lifetime at R 0.99 s = 1.384e-08, linewidth at R 0.99 Hz = 1.150e+07, finesse at R 0.9995 = 1.256e+03, lifetime at R 0.9995 s = 6.666e-08. Further computed values are saturation ratio lifetime = 4.817. The central question is stated as follows: How much storage time, spectral width and round-trip loss follow from a stated mirror reflectivity for a five-centimetre resonator at 780 nm, and at what reflectivity does further coating improvement stop buying useful time because other losses dominate? The answer obtained here is conditional on the assumptions listed in the paper and in the deposited calculation; changing an assumption changes the numbers in the way the sensitivity discussion describes. Laboratory resonators of this size are commonly quoted with finesse values from a few hundred for coated optics to well above one hundred thousand for supermirror coatings, so a sweep across that interval tests both ordinary and demanding coatings. The work is a computation, not a laboratory measurement, and it is labelled accordingly. Where the computed result is unfavourable to the device or effect under study, that outcome is reported in the same terms as a favourable one, because a bound that only appears when it is welcome is not a bound at all. All numerical statements in this abstract are reproduced by the deposited script from the stated inputs.
Presented here are results on a silicon ring resonator photon pair source with a high heralding efficiency. Previous ring resonator sources suffered from an effective 50% loss because, in order to generate the photons, the pump must be able to couple into the resonator which is an effective loss channel. However, in practice the optical loss of the pump can be traded off for a dramatic increase in heralding efficiency. This research found theoretically that the heralding efficiency should increase by a factor of ∼ 3:75 with a factor of 10 increase in the required pump power. This was demonstrated experimentally by varying the separation (gap) between the input waveguide and the ring while maintaining a constant drop port gap. The ring (R = 18:5μm, W = 500nm, and H = 220nm) was pumped by a tunable laser (λ ≈ 1550nm). The non-degenerate photons, produced via spontaneous four wave mixing, exited the ring and were coupled to fiber upon which they were filtered symmetrically about the pump. Coincidence counts were collected for all possible photon path combinations (through and drop port) and the ratio of the drop port coincidences to the sum of the drop port and cross term coincidences (one photon from the drop port and one from the through port) was calculated. With a 350nm pump waveguide gap (2:33 times larger than the drop port gap) we confirmed our theoretical predictions, with an observed improvement in heralding efficiency by a factor of ∼ 2:61 (96:7% of correlated photons coupled out of the drop port). These results will enable increased photon flux integrated photon sources which can be utilized for high performance quantum computing and communication systems.
One of the key building blocks of quantum photonic systems is a source of indistinguishable photons. Silicon ring resonators can be used as photon pair sources by taking advantage of silicon's large third order nonlinearity with a process known as spontaneous four wave mixing. These sources are capable of producing pairs of indistinguishable photons but typically suffer from an effective 50% loss. By slightly decoupling the input waveguide from the ring, the desired photons generated in the ring can be directed to the drop port. Thus, the ratio between the coincidences from the drop port and the total number of coincidences from all ports (coincidence efficiency) can be significantly increased, with the trade-off being that the pump is less efficiently coupled into the ring. This asymmetric coupling scheme was used to demonstrate a dual-bus microring source with a coincidence efficiency of ~96%. Unfortunately, the penalty to pump power was quite large, with a required ~10x increase in the pump power to maintain the same pair generation rate.\nTo further improve upon this result, a microring source was designed with multipoint evanescent couplers to induce a strong spectral dependence in the coupling coefficients. This coupler design can be used on both sides of the ring resonator so that resonances supported by one of the couplers are suppressed by the other. This is the ideal configuration for a ring-based photon-pair source as it can only support the pump photons at the input side while only allowing the generated photons to leave through the output side. Asymmetric coupling was also used in this configuration but in a different way than in the previous source. In this case, the input side of the ring was configured to be critically coupled for maximal resonance enhancement while the output side was configured to be over coupled to minimize photon-pair loss within the ring. This device design was used to demonstrate a photon-pair source with coincidence efficiencies of 0.9981+-6.425x10^-4 and 0.9979+-1.665x10^-3 for degenerate and non-degenerate pump configuration respectively.\nIn addition to the source development, work was done to move some of the pump rejection filtering onto the photonic chip. While the fabricated device only exhibited an extinction of 50 dB, the root cause of the limited extinction was explored and a new filter design was proposed to overcome these limitations. With the combination of the microring source with its greatly improved efficiency and the movement toward reducing the required off-chip filtering, this work represents a significant advancement in the scalability of integrated quantum photonic systems which can enable high performance quantum computing and communication systems.
Photonic chips with silicon nitride (Si3N4\mathrm{Si_3N_4}Si3​N4​) microring resonators are well established as heralded single-photon sources, but their operation as frequency-degenerate twin-photon sources has not previously been demonstrated. Here, we realise a twin-photon source at telecommunication wavelengths in a Si3N4\mathrm{Si_3N_4}Si3​N4​ ring microresonator via an inverse four-wave mixing (FWM) process, in which two photons from spectrally distinct pumps are converted into a pair of identical twin photons. The measurements show a maximum coincidence-to-accidental ratio (CAR) of 5.4±0.65.4\pm0.65.4±0.6. In addition, the microresonator functions as a heralded single-photon source through pump-degenerate spontaneous four-wave mixing (SFWM), exhibiting a spectral purity of P=0.67±0.05P=0.67\pm0.05P=0.67±0.05 and a heralded anti-bunching of gh(2)(0)=0.0042±0.0015g^{(2)}_h(0)=0.0042\pm0.0015gh(2)​(0)=0.0042±0.0015. Together, these results demonstrate both photon-generation schemes on a single integrated Si3N4\mathrm{Si_3N_4}Si3​N4​ platform, highlighting its potential for scalable, tailored quantum light generation.
Ring resonators are used as photon pair sources by taking advantage of the materials second or third order non- linearities through the processes of spontaneous parametric downconversion and spontaneous four wave mixing respectively. Two materials of interest for these applications are silicon for the infrared and aluminum nitride for the ultraviolet through the infrared. When fabricated into ring type sources they are capable of producing pairs of indistinguishable photons but typically suffer from an effective 50% loss. By slightly decoupling the input waveguide from the ring, the drop port coincidence ratio can be significantly increased with the trade-off being that the pump is less efficiently coupled into the ring. Ring resonators with this design have been demonstrated having coincidence ratios of 96% but requiring a factor of ~10 increase in the pump power. Through the modification of the coupling design that relies on additional spectral dependence, it is possible to achieve similar coincidence ratios without the increased pumping requirement. This can be achieved by coupling the input waveguide to the ring multiple times, thus creating a Mach-Zehnder interferometer. This coupler design can be used on both sides of the ring resonator so that resonances supported by one of the couplers are suppressed by the other. This is the ideal configuration for a photon-pair source as it can only support the pump photons at the input side while only allowing the generated photons to leave through the output side. Recently, this device has been realized with preliminary results exhibiting the desired spectral dependence and with a coincidence ratio as high as ~ 97% while allowing the pump to be nearly critically coupled to the ring. The demonstrated near unity coincidence ratio infers a near maximal heralding efficiency from the fabricated device. This device has the potential to greatly improve the scalability and performance of quantum computing and communication systems.