A single photon that enters a Fabry-Perot resonator leaves again after a dwell time set by how often it reflects and how much light escapes at each reflection. That dwell time decides whether the photon can be held long enough for a control operation, a heralding check, or a synchronisation delay, and it also sets the spectral width the source must match. This study computes the quantities that follow from stated assumptions for a symmetric two-mirror Fabry-Perot cavity of length 0.05 m, wavelength 780 nm, with a fixed additional round-trip loss of 0.002 in intensity, using the relations set out in the Methods. The headline results are finesse at R 0.99 = 260.7, lifetime at R 0.99 s = 1.384e-08, linewidth at R 0.99 Hz = 1.150e+07, finesse at R 0.9995 = 1.256e+03, lifetime at R 0.9995 s = 6.666e-08. Further computed values are saturation ratio lifetime = 4.817. The central question is stated as follows: How much storage time, spectral width and round-trip loss follow from a stated mirror reflectivity for a five-centimetre resonator at 780 nm, and at what reflectivity does further coating improvement stop buying useful time because other losses dominate? The answer obtained here is conditional on the assumptions listed in the paper and in the deposited calculation; changing an assumption changes the numbers in the way the sensitivity discussion describes. Laboratory resonators of this size are commonly quoted with finesse values from a few hundred for coated optics to well above one hundred thousand for supermirror coatings, so a sweep across that interval tests both ordinary and demanding coatings. The work is a computation, not a laboratory measurement, and it is labelled accordingly. Where the computed result is unfavourable to the device or effect under study, that outcome is reported in the same terms as a favourable one, because a bound that only appears when it is welcome is not a bound at all. All numerical statements in this abstract are reproduced by the deposited script from the stated inputs.
A single photon that enters a Fabry-Perot resonator leaves again after a dwell time set by how often it reflects and how much light escapes at each reflection. That dwell time decides whether the photon can be held long enough for a control operation, a heralding check, or a synchronisation delay, and it also sets the spectral width the source must match. This study computes the quantities that follow from stated assumptions for a symmetric two-mirror Fabry-Perot cavity of length 0.05 m, wavelength 780 nm, with a fixed additional round-trip loss of 0.002 in intensity, using the relations set out in the Methods. The headline results are finesse at R 0.99 = 260.7, lifetime at R 0.99 s = 1.384e-08, linewidth at R 0.99 Hz = 1.150e+07, finesse at R 0.9995 = 1.256e+03, lifetime at R 0.9995 s = 6.666e-08. Further computed values are saturation ratio lifetime = 4.817. The central question is stated as follows: How much storage time, spectral width and round-trip loss follow from a stated mirror reflectivity for a five-centimetre resonator at 780 nm, and at what reflectivity does further coating improvement stop buying useful time because other losses dominate? The answer obtained here is conditional on the assumptions listed in the paper and in the deposited calculation; changing an assumption changes the numbers in the way the sensitivity discussion describes. Laboratory resonators of this size are commonly quoted with finesse values from a few hundred for coated optics to well above one hundred thousand for supermirror coatings, so a sweep across that interval tests both ordinary and demanding coatings. The work is a computation, not a laboratory measurement, and it is labelled accordingly. Where the computed result is unfavourable to the device or effect under study, that outcome is reported in the same terms as a favourable one, because a bound that only appears when it is welcome is not a bound at all. All numerical statements in this abstract are reproduced by the deposited script from the stated inputs.
On a photonic chip, a ring resonator stores light for a time set by its circumference and its propagation loss. That storage time, together with the free spectral range, decides whether the ring can act as a filter, a delay, or a photon-pair source enhancement. This study computes the quantities that follow from stated assumptions for silicon nitride waveguide rings, group index 2.0, wavelength 1550 nm, propagation loss 0.1, 0.5 and 1.0 dB per centimetre, using the relations set out in the Methods. The headline results are Q at 0.1 dBcm = 3.521e+06, lifetime at 0.1 dBcm s = 2.897e-09, Q at 1 dBcm = 3.521e+05, lifetime at 1 dBcm s = 2.897e-10, FSR at 100 um Hz = 2.386e+11. The central question is stated as follows: For silicon nitride rings of radius 20 to 200 micrometres with stated propagation losses, what quality factor, photon lifetime and free spectral range follow, and which combination reaches a lifetime of one nanosecond? The answer obtained here is conditional on the assumptions listed in the paper and in the deposited calculation; changing an assumption changes the numbers in the way the sensitivity discussion describes. Integrated rings are reported with quality factors from ten thousand to above ten million depending on material and loss, so the computed table spans the practical interval. The work is a computation, not a laboratory measurement, and it is labelled accordingly. Where the computed result is unfavourable to the device or effect under study, that outcome is reported in the same terms as a favourable one, because a bound that only appears when it is welcome is not a bound at all. All numerical statements in this abstract are reproduced by the deposited script from the stated inputs.
Design blueprint derived from the source paper (DOI 10.5281/zenodo.24159701): On a photonic chip, a ring resonator stores light for a time set by its circumference and its propagation loss. That storage time, together with the free spectral range, decides whether the ring can act as a filter, a delay, or a photon-pair source enhancement. This study computes the quantities that follow from stated assumptions for silicon nitride waveguide rings, group index 2.0, wavelength 1550 nm, propagation loss 0.1, 0.5 and 1.0 dB per centimetre, using the relations set out in the Methods. The headline results are Q at 0.1 dBcm = 3.521e+06, lifetime at 0.1 dBcm s = 2.897e-09, Q at 1 dBcm = 3.521e+05, lifetime at 1 dBcm s = 2.897e-10, FSR at 100 um Hz = 2.386e+11. The central question is stated as follows: For silicon nitride rings of radius 20 to 200 micrometres with stated propagation losses, what quality factor, photon lifetime and free spectral range follow, and which combination reaches a lifetime of one nanosecond? The answer obtained here is conditional on the assumptions listed in the paper and in the deposited calculation; changing an assumption changes the numbers in the way the sensitivity discussion describes. Integrated rings are reported with quality factors from ten thousand to above ten million depending on material and loss, so the computed table spans the practical interval. The work is a computation, not a laboratory measurement, and it is labelled accordingly. Where the computed result is unfavourable to the device or effect under study, that outcome is reported in the same terms as a favourable one, because a bound that only appears when it is welcome is not a bound at all. All numerical statements in this abstract are reproduced by the deposited script from the stated inputs. Status: DESIGN BLUEPRINT — SIMULATED, NOT MEASURED — NOT BUILT. All numbers are simulated values from the source paper's computation, deposited with this blueprint as compute.py and results.json. AI-use disclosure: Dave, an AI research system, assisted with the computation and drafting under the author's direction; author of record William Alexander Aldred.
Storing a photon as a collective excitation in an atomic ensemble succeeds with a probability that rises with optical depth and falls with decoherence during the storage interval. Optical depth is therefore the first design number for an electromagnetically induced transparency memory. This study computes the quantities that follow from stated assumptions for a rubidium ensemble, control-field optimised at each optical depth, ground-state coherence times of 100 microseconds and 1 millisecond, using the relations set out in the Methods. The headline results are efficiency at d 20 = 0.9773, efficiency at d 100 = 0.9999, depth for 90pct = 8.819, eff d100 with 100us coherence = 0.8187, eff d100 with 1ms coherence = 0.9801. The central question is stated as follows: What optical depth gives ninety percent storage-and-retrieval efficiency in the standard model, and how does a finite ground-state coherence time change that requirement for a ten-microsecond storage? The answer obtained here is conditional on the assumptions listed in the paper and in the deposited calculation; changing an assumption changes the numbers in the way the sensitivity discussion describes. Laboratory memories report efficiencies from a few percent to above eighty percent, with the highest values in high-optical-depth cold ensembles and cavities. The work is a computation, not a laboratory measurement, and it is labelled accordingly. Where the computed result is unfavourable to the device or effect under study, that outcome is reported in the same terms as a favourable one, because a bound that only appears when it is welcome is not a bound at all. All numerical statements in this abstract are reproduced by the deposited script from the stated inputs.
Fiber Fabry-Perot cavities, formed by micro-machined mirrors on the end-facets of optical fibers, are used in an increasing number of technical and scientific applications. Some of the most promising areas of application of these optical micro-resonators with high finesse and small mode volume are in the field of quantum communication and information. The resonator-enhanced light-matter interaction, for instance, provide basis for the realization of efficient optical interfaces between stationary matter-based quantum nodes and flying single-photon qubits. To date fiber Fabry-Perot cavities have been successfully applied in experiments interfacing single photons with a wide range of quantum systems, including cold atoms, ions and solid state emitters as well as quantum optomechanical experiments. Here we address some important practical questions that arise during the experimental implementation of high finesse fiber Fabry-Perot cavities: How can optimal fiber cavity alignment be achieved and how can the efficiency of coupling light from the optical fibers to the cavity mode and vice versa be characterized? How should optical fiber cavities be constructed and stabilized to fulfill their potential for miniaturization and integration into robust scientific and technological devices that can operate outside of dedicated laboratory environments in the future? The first two questions we answer with an analytic mode matching calculation that relates the alignment dependent fiber-to-cavity mode-matching efficiency to the easily measurable dip in the reflected light power at the cavity resonance. Our general analysis provides a simple recipe for the optimal alignment of fiber Fabry-Perot cavities and moreover for the first time explains the asymmetry in their reflective line shapes. The latter question we explore by investigating a novel, intrinsically rigid fiber cavity design that makes use of the high passive stability of a monolithic cavity spacer and employs thermal self-locking and external temperature tuning. The performance of this novel approach is compared to a more traditional, piezomechanically-actuated resonator that is feedback stabilized to a reference laser based on the Pound-Drever-Hall locking technique. Finally, with the application of single photon interfacing in mind we discuss the issue of fiber-generated background photons in Fiber Fabry-Perot cavities. We believe that, due to their simplicity, compactness and robustness, rigid fiber cavities could be a promising solution for miniaturized, integratable and scalable cavity quantum electrodynamic devices and further applications of FFPC with similar requirements.
The exact expressions of finesse and full width at half maximum (FWHM) of the Airy distribution of a Fabry-P\'erot (FP) resonator are derived, which solves the breakdown problem at ultralow reflectivity in traditional formulas. We demonstrate that, when the cavity-mirror reflectivity $R\ensuremath{\rightarrow}0$, the FWHM approaches half of the free spectral range rather than infinity; moreover, the cavity finesse F approaches 2 rather than zero. These expressions are useful for the development of bad-cavity lasers, such as the four-level active optical clock based on the strong atomic transition of cesium. Also, the exact expressions of the FWHM and finesse of the reflection distribution composed of reflected mode profiles are derived, which separately intersect with that of the Airy one at R=0. In addition, the characteristics of an antiresonant cavity, the frequency of which is exactly at the center of two adjacent resonant cavity modes, are analyzed. It is demonstrated that at the resonant and antiresonant frequencies the enhancement and inhibition of intracavity light intensity caused by the FP cavity are symmetrical in the logarithmic view. Furthermore, we provide a universal expression of the cavity-enhancement factor rather than the classical representation of ``$\text{2}\mathcal{F}/\phantom{\text{2}\mathcal{F}\ensuremath{\pi}}\phantom{\rule{0.0pt}{0ex}}\ensuremath{\pi}$,'' which is inadequate for the high-loss cavity because the cavity-enhancement factor should naturally reach 1 when $R\ensuremath{\rightarrow}0$. Finally, we extend the application of the antiresonant cavity to an inhibited laser, the frequency of which has a stronger suppression effect on the cavity-length thermal noise than the traditional resonant laser.
Summary form only given. It is often assumed that spontaneous emission by an emitter placed inside a Fabry-Perot resonator into one of the longitudinal resonator modes occurs with the spectral shape of that mode, because it is triggered by a vacuum photon that has the same spectral shape as the resonator mode. More generally, broadband luminescence by many such emitters would then have to occur with the spectral shape of the Airy distribution of the Fabry-Perot resonator [1]. The assumption is incorrect in several respects. (i) The uncertainty principle for energy and time predicts that a vacuum photon at 1 μm wavelength survives approx. τ = 1 fs, i.e., it travels a hundred nanometers, shorter than the length of most optical resonators, except for nano-resonators. Consequently, it does not experience interference after one round trip, hence vacuum energy should occur as white light. (ii) Spontaneous emission typically occurs over a time that is much longer than one resonator-round-trip time [2]. If the emission time were infinite, then white-light vacuum energy would induce spontaneous emission that establishes the Airy distribution, because the emission interferes with itself over an infinite number of round trips. (iii) If vacuum energy resembled the spectral properties of the mode, the spectral distribution would be narrower. (iv) When also considering the finite emission lifetime, we find surprising relations between different resonator parameters. We investigate a single emitter (e.g. rare-earth ion, quantum dot) with a lifetime r inside a resonator of length t and mirror reflectivities R1 = R2 = R, triggered by white-light vacuum energy. The electric field is modelled as a superposition of plane waves emitted at integer multiples of the round-trip time. We calculate the amplitude of the newly emitted wave, taking into account the loss of energy of the emitter, and calculate the normalized spectral-intensity profile. For a sufficient number of round trips, we find convergence and calculate the FWHM linewidth A v. The results for different ratios of Liz and different R are shown in Fig. 1 The position on the x-axis for different combinations of emitters and resonator lengths is outlined in Table 1.