Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE

Efficiently heralded silicon ring resonator photon-pair source

Jeffrey A. Steidle, Michael L. Fanto, Christopher C. Tison, Zihao Wang, Paul M. Alsing, Stefan F. Preble

Published May 19, 2016• 3 citations
Publisher

Abstract

Presented here are results on a silicon ring resonator photon pair source with a high heralding efficiency. Previous ring resonator sources suffered from an effective 50% loss because, in order to generate the photons, the pump must be able to couple into the resonator which is an effective loss channel. However, in practice the optical loss of the pump can be traded off for a dramatic increase in heralding efficiency. This research found theoretically that the heralding efficiency should increase by a factor of ∼ 3:75 with a factor of 10 increase in the required pump power. This was demonstrated experimentally by varying the separation (gap) between the input waveguide and the ring while maintaining a constant drop port gap. The ring (R = 18:5μm, W = 500nm, and H = 220nm) was pumped by a tunable laser (λ ≈ 1550nm). The non-degenerate photons, produced via spontaneous four wave mixing, exited the ring and were coupled to fiber upon which they were filtered symmetrically about the pump. Coincidence counts were collected for all possible photon path combinations (through and drop port) and the ratio of the drop port coincidences to the sum of the drop port and cross term coincidences (one photon from the drop port and one from the through port) was calculated. With a 350nm pump waveguide gap (2:33 times larger than the drop port gap) we confirmed our theoretical predictions, with an observed improvement in heralding efficiency by a factor of ∼ 2:61 (96:7% of correlated photons coupled out of the drop port). These results will enable increased photon flux integrated photon sources which can be utilized for high performance quantum computing and communication systems.

DOI
10.1117/12.2223941

Related papers

Path to increasing the coincidence efficiency of integrated resonant photon sources

C. C. Tison, J. A. Steidle, M. L. Fanto +5 more

Silicon ring resonators are used as photon pair sources by taking advantage of silicon's large third order nonlinearity with a process known as spontaneous four wave mixing. These sources are capable of producing pairs of indistinguishable photons but typically suffer from an effective $50\%$ loss. By slightly decoupling the input waveguide from the ring, the drop port coincidence ratio can be significantly increased with the trade-off being that the pump is less efficiently coupled into the ring. Ring resonators with this design have been demonstrated having coincidence ratios of $\sim 96\%$ but requiring a factor of $\sim 10$ increase in the pump power. Through the modification of the coupling design that relies on additional spectral dependence, it is possible to achieve similar coincidence ratios without the increased pumping requirement. This can be achieved by coupling the input waveguide to the ring multiple times, thus creating a Mach-Zehnder interferometer. This coupler design can be used on both sides of the ring resonator so that resonances supported by one of the couplers are suppressed by the other. This is the ideal configuration for a photon-pair source as it can only support the pump photons at the input side while only allowing the generated photons to leave through the output side. Recently, this device has been realized with preliminary results exhibiting the desired spectral dependence and with a coincidence ratio as high as $\sim 97\%$ while allowing the pump to be nearly critically coupled to the ring. The demonstrated near unity coincidence ratio infers a near maximal heralding efficiency from the fabricated device. This device has the potential to greatly improve the scalability and performance of quantum computing and communication systems.

arXiv:1703.08368•Optics Express•Dec 20, 2017•45 citations

Development of a High Performance Resonant Photon-Pair Source in Silicon

Jeffrey A. Steidle

One of the key building blocks of quantum photonic systems is a source of indistinguishable photons. Silicon ring resonators can be used as photon pair sources by taking advantage of silicon's large third order nonlinearity with a process known as spontaneous four wave mixing. These sources are capable of producing pairs of indistinguishable photons but typically suffer from an effective 50% loss. By slightly decoupling the input waveguide from the ring, the desired photons generated in the ring can be directed to the drop port. Thus, the ratio between the coincidences from the drop port and the total number of coincidences from all ports (coincidence efficiency) can be significantly increased, with the trade-off being that the pump is less efficiently coupled into the ring. This asymmetric coupling scheme was used to demonstrate a dual-bus microring source with a coincidence efficiency of ~96%. Unfortunately, the penalty to pump power was quite large, with a required ~10x increase in the pump power to maintain the same pair generation rate.\nTo further improve upon this result, a microring source was designed with multipoint evanescent couplers to induce a strong spectral dependence in the coupling coefficients. This coupler design can be used on both sides of the ring resonator so that resonances supported by one of the couplers are suppressed by the other. This is the ideal configuration for a ring-based photon-pair source as it can only support the pump photons at the input side while only allowing the generated photons to leave through the output side. Asymmetric coupling was also used in this configuration but in a different way than in the previous source. In this case, the input side of the ring was configured to be critically coupled for maximal resonance enhancement while the output side was configured to be over coupled to minimize photon-pair loss within the ring. This device design was used to demonstrate a photon-pair source with coincidence efficiencies of 0.9981+-6.425x10^-4 and 0.9979+-1.665x10^-3 for degenerate and non-degenerate pump configuration respectively.\nIn addition to the source development, work was done to move some of the pump rejection filtering onto the photonic chip. While the fabricated device only exhibited an extinction of 50 dB, the root cause of the limited extinction was explored and a new filter design was proposed to overcome these limitations. With the combination of the microring source with its greatly improved efficiency and the movement toward reducing the required off-chip filtering, this work represents a significant advancement in the scalability of integrated quantum photonic systems which can enable high performance quantum computing and communication systems.

•Jan 1, 2019•0 citations

Heralding efficiency and brightness optimization of a micro-ring resonator via tunable coupling

Nathan Moses, Marcus J. Clark, Alex S. Clark +2 more

Efficient and bright single photon sources on photonic chips are key to scaling quantum technologies. Spontaneous four wave mixing in micro-ring resonators creates excellent narrowband and tunable photon sources. We experimentally demonstrate the optimization of heralding efficiency and brightness by tuning the coupling of the pump, signal and idler modes into the resonator whilst operating in a pulsed pump regime. We observe a maximum detected pair rate of over 93,000~coincidences per second in a moderately over-coupled regime, alongside a high intrinsic idler heralding efficiency of 97.87$\pm$8.97\% when operating close to maximal over-coupling. The measured dependence on coupling strength is in strong agreement with theoretical predictions, experimentally validating the predicted trade-off between brightness and heralding efficiency.

quant-pharXiv:2602.06790•Feb 9, 2026•0 citations

Integrated photon sources for quantum information science applications

Paul M. Alsing, Dirk Englund, Neville A. Mogent +8 more

Ring resonators are used as photon pair sources by taking advantage of the materials second or third order non- linearities through the processes of spontaneous parametric downconversion and spontaneous four wave mixing respectively. Two materials of interest for these applications are silicon for the infrared and aluminum nitride for the ultraviolet through the infrared. When fabricated into ring type sources they are capable of producing pairs of indistinguishable photons but typically suffer from an effective 50% loss. By slightly decoupling the input waveguide from the ring, the drop port coincidence ratio can be significantly increased with the trade-off being that the pump is less efficiently coupled into the ring. Ring resonators with this design have been demonstrated having coincidence ratios of 96% but requiring a factor of ~10 increase in the pump power. Through the modification of the coupling design that relies on additional spectral dependence, it is possible to achieve similar coincidence ratios without the increased pumping requirement. This can be achieved by coupling the input waveguide to the ring multiple times, thus creating a Mach-Zehnder interferometer. This coupler design can be used on both sides of the ring resonator so that resonances supported by one of the couplers are suppressed by the other. This is the ideal configuration for a photon-pair source as it can only support the pump photons at the input side while only allowing the generated photons to leave through the output side. Recently, this device has been realized with preliminary results exhibiting the desired spectral dependence and with a coincidence ratio as high as ~ 97% while allowing the pump to be nearly critically coupled to the ring. The demonstrated near unity coincidence ratio infers a near maximal heralding efficiency from the fabricated device. This device has the potential to greatly improve the scalability and performance of quantum computing and communication systems.

•Oct 5, 2017•1 citation

No free lunch: the trade-off between heralding rate and efficiency in microresonator-based heralded single photon sources

Z. Vernon, M. Liscidini, J. E. Sipe

Generation of heralded single photons has recently been demonstrated using spontaneous four-wave mixing in integrated microresonators. While the results of coincidence measurements on the generated photon pairs from these systems show promise for their utility in heralding applications, such measurements do not reveal all of the effects of photon losses within the resonator. These effects, which include a significant degradation of the heralding efficiency, depend strongly on the relative strengths of the coupling of the ring modes to loss modes and channel modes. We show that the common choice of critical coupling neither optimizes the rate of successfully heralded photons nor coincidences and derives the coupling conditions needed to do so. Optimizing these rates has a considerable negative effect on the heralding efficiency.

arXiv:1512.04879•Optics Letters•Feb 8, 2016•58 citations

High spectral purity silicon ring resonator photon-pair source

Jeffrey A. Steidle, Michael L. Fanto, Christopher C. Tison +3 more

Here we present the experimental demonstration of a Silicon ring resonator photon-pair source. The crystalline Silicon ring resonator (radius of 18.5μm) was designed to realize low dispersion across multiple resonances, which allows for operation with a high quality factor of Q~50k. In turn, the source exhibits very high brightness of >3x105 photons/s/mW2/GHz since the produced photon pairs have a very narrow bandwidth. Furthermore, the waveguidefiber coupling loss was minimized to <1.5dB using an inverse tapered waveguide (tip width of ~150nm over a 300μm length) that is butt-coupled to a high-NA fiber (Nufern UHNA-7). This ensured minimal loss of photon pairs to the detectors, which enabled very high purity photon pairs with minimal noise, as exhibited by a very high Coincidental-Accidental Ratio of >1900. The low coupling loss (3dB fiber-fiber) also allowed for operation with very low off-chip pump power of <200μW. In addition, the zero dispersion of the ring resonator resulted in the production of a photon-pair comb across multiple resonances symmetric about the pump resonance (every ~5nm spanning >20nm), which could be used in future wavelength division multiplexed quantum networks.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•May 21, 2015•13 citations
Presented here are results on a silicon ring resonator photon pair source with a high heralding efficiency. Previous ring resonator sources suffered from an effective 50% loss because, in order to generate the photons, the pump must be able to couple into the resonator which is an effective loss channel. However, in practice the optical loss of the pump can be traded off for a dramatic increase in heralding efficiency. This research found theoretically that the heralding efficiency should increase by a factor of ∼ 3:75 with a factor of 10 increase in the required pump power. This was demonstrated experimentally by varying the separation (gap) between the input waveguide and the ring while maintaining a constant drop port gap. The ring (R = 18:5μm, W = 500nm, and H = 220nm) was pumped by a tunable laser (λ ≈ 1550nm). The non-degenerate photons, produced via spontaneous four wave mixing, exited the ring and were coupled to fiber upon which they were filtered symmetrically about the pump. Coincidence counts were collected for all possible photon path combinations (through and drop port) and the ratio of the drop port coincidences to the sum of the drop port and cross term coincidences (one photon from the drop port and one from the through port) was calculated. With a 350nm pump waveguide gap (2:33 times larger than the drop port gap) we confirmed our theoretical predictions, with an observed improvement in heralding efficiency by a factor of ∼ 2:61 (96:7% of correlated photons coupled out of the drop port). These results will enable increased photon flux integrated photon sources which can be utilized for high performance quantum computing and communication systems.
Silicon ring resonators are used as photon pair sources by taking advantage of silicon's large third order nonlinearity with a process known as spontaneous four wave mixing. These sources are capable of producing pairs of indistinguishable photons but typically suffer from an effective 50%50\%50% loss. By slightly decoupling the input waveguide from the ring, the drop port coincidence ratio can be significantly increased with the trade-off being that the pump is less efficiently coupled into the ring. Ring resonators with this design have been demonstrated having coincidence ratios of ∼96%\sim 96\%∼96% but requiring a factor of ∼10\sim 10∼10 increase in the pump power. Through the modification of the coupling design that relies on additional spectral dependence, it is possible to achieve similar coincidence ratios without the increased pumping requirement. This can be achieved by coupling the input waveguide to the ring multiple times, thus creating a Mach-Zehnder interferometer. This coupler design can be used on both sides of the ring resonator so that resonances supported by one of the couplers are suppressed by the other. This is the ideal configuration for a photon-pair source as it can only support the pump photons at the input side while only allowing the generated photons to leave through the output side. Recently, this device has been realized with preliminary results exhibiting the desired spectral dependence and with a coincidence ratio as high as ∼97%\sim 97\%∼97% while allowing the pump to be nearly critically coupled to the ring. The demonstrated near unity coincidence ratio infers a near maximal heralding efficiency from the fabricated device. This device has the potential to greatly improve the scalability and performance of quantum computing and communication systems.
One of the key building blocks of quantum photonic systems is a source of indistinguishable photons. Silicon ring resonators can be used as photon pair sources by taking advantage of silicon's large third order nonlinearity with a process known as spontaneous four wave mixing. These sources are capable of producing pairs of indistinguishable photons but typically suffer from an effective 50% loss. By slightly decoupling the input waveguide from the ring, the desired photons generated in the ring can be directed to the drop port. Thus, the ratio between the coincidences from the drop port and the total number of coincidences from all ports (coincidence efficiency) can be significantly increased, with the trade-off being that the pump is less efficiently coupled into the ring. This asymmetric coupling scheme was used to demonstrate a dual-bus microring source with a coincidence efficiency of ~96%. Unfortunately, the penalty to pump power was quite large, with a required ~10x increase in the pump power to maintain the same pair generation rate.\nTo further improve upon this result, a microring source was designed with multipoint evanescent couplers to induce a strong spectral dependence in the coupling coefficients. This coupler design can be used on both sides of the ring resonator so that resonances supported by one of the couplers are suppressed by the other. This is the ideal configuration for a ring-based photon-pair source as it can only support the pump photons at the input side while only allowing the generated photons to leave through the output side. Asymmetric coupling was also used in this configuration but in a different way than in the previous source. In this case, the input side of the ring was configured to be critically coupled for maximal resonance enhancement while the output side was configured to be over coupled to minimize photon-pair loss within the ring. This device design was used to demonstrate a photon-pair source with coincidence efficiencies of 0.9981+-6.425x10^-4 and 0.9979+-1.665x10^-3 for degenerate and non-degenerate pump configuration respectively.\nIn addition to the source development, work was done to move some of the pump rejection filtering onto the photonic chip. While the fabricated device only exhibited an extinction of 50 dB, the root cause of the limited extinction was explored and a new filter design was proposed to overcome these limitations. With the combination of the microring source with its greatly improved efficiency and the movement toward reducing the required off-chip filtering, this work represents a significant advancement in the scalability of integrated quantum photonic systems which can enable high performance quantum computing and communication systems.
Efficient and bright single photon sources on photonic chips are key to scaling quantum technologies. Spontaneous four wave mixing in micro-ring resonators creates excellent narrowband and tunable photon sources. We experimentally demonstrate the optimization of heralding efficiency and brightness by tuning the coupling of the pump, signal and idler modes into the resonator whilst operating in a pulsed pump regime. We observe a maximum detected pair rate of over 93,000~coincidences per second in a moderately over-coupled regime, alongside a high intrinsic idler heralding efficiency of 97.87$\pm$8.97\% when operating close to maximal over-coupling. The measured dependence on coupling strength is in strong agreement with theoretical predictions, experimentally validating the predicted trade-off between brightness and heralding efficiency.
Ring resonators are used as photon pair sources by taking advantage of the materials second or third order non- linearities through the processes of spontaneous parametric downconversion and spontaneous four wave mixing respectively. Two materials of interest for these applications are silicon for the infrared and aluminum nitride for the ultraviolet through the infrared. When fabricated into ring type sources they are capable of producing pairs of indistinguishable photons but typically suffer from an effective 50% loss. By slightly decoupling the input waveguide from the ring, the drop port coincidence ratio can be significantly increased with the trade-off being that the pump is less efficiently coupled into the ring. Ring resonators with this design have been demonstrated having coincidence ratios of 96% but requiring a factor of ~10 increase in the pump power. Through the modification of the coupling design that relies on additional spectral dependence, it is possible to achieve similar coincidence ratios without the increased pumping requirement. This can be achieved by coupling the input waveguide to the ring multiple times, thus creating a Mach-Zehnder interferometer. This coupler design can be used on both sides of the ring resonator so that resonances supported by one of the couplers are suppressed by the other. This is the ideal configuration for a photon-pair source as it can only support the pump photons at the input side while only allowing the generated photons to leave through the output side. Recently, this device has been realized with preliminary results exhibiting the desired spectral dependence and with a coincidence ratio as high as ~ 97% while allowing the pump to be nearly critically coupled to the ring. The demonstrated near unity coincidence ratio infers a near maximal heralding efficiency from the fabricated device. This device has the potential to greatly improve the scalability and performance of quantum computing and communication systems.
Generation of heralded single photons has recently been demonstrated using spontaneous four-wave mixing in integrated microresonators. While the results of coincidence measurements on the generated photon pairs from these systems show promise for their utility in heralding applications, such measurements do not reveal all of the effects of photon losses within the resonator. These effects, which include a significant degradation of the heralding efficiency, depend strongly on the relative strengths of the coupling of the ring modes to loss modes and channel modes. We show that the common choice of critical coupling neither optimizes the rate of successfully heralded photons nor coincidences and derives the coupling conditions needed to do so. Optimizing these rates has a considerable negative effect on the heralding efficiency.
Here we present the experimental demonstration of a Silicon ring resonator photon-pair source. The crystalline Silicon ring resonator (radius of 18.5μm) was designed to realize low dispersion across multiple resonances, which allows for operation with a high quality factor of Q~50k. In turn, the source exhibits very high brightness of >3x105 photons/s/mW2/GHz since the produced photon pairs have a very narrow bandwidth. Furthermore, the waveguidefiber coupling loss was minimized to <1.5dB using an inverse tapered waveguide (tip width of ~150nm over a 300μm length) that is butt-coupled to a high-NA fiber (Nufern UHNA-7). This ensured minimal loss of photon pairs to the detectors, which enabled very high purity photon pairs with minimal noise, as exhibited by a very high Coincidental-Accidental Ratio of >1900. The low coupling loss (3dB fiber-fiber) also allowed for operation with very low off-chip pump power of <200μW. In addition, the zero dispersion of the ring resonator resulted in the production of a photon-pair comb across multiple resonances symmetric about the pump resonance (every ~5nm spanning >20nm), which could be used in future wavelength division multiplexed quantum networks.