Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Conference on Precision Electromagnetic Measurements

Noise Analysis for Millimeter-Wave Driving of High-Temperature Superconductor Josephson Junction Arrays

Changhao Zhao, Yafang Lian, Da Xu, Yang Shi, Yunlin Liu, Kunli Zhou, Jifeng Qu, Yunfeng Lu, Jianting Zhao

Published Sep 1, 2026• 0 citations
Publisher

Abstract

High-temperature superconductor Josephson junction arrays were irradiated with millimeter-wave of approximately 70 GHz. The junction arrays were composed of 15 bicrystal YBCO junctions in series and produced DC voltage output of up to 2 mV, which was sampled by a commercial nanovoltmeter. The measured Vppof voltage fluctuations was on the order of 0.6 μV, exceeding the intrinsic fluctuation of the nanovoltmeter itself. To identify the origin of the excessive fluctuations, the phase noise and harmonic distortion of the millimeter-wave signal were analyzed and finally excluded from the major cause of the performance degradation. While millimeter-wave filtering and DC wiring of the apparatus can be improved, the results showed the feasibility of the millimeter-wave driving architecture and the noise analysis framework can be applied to development of even higher frequency drives into THz range.

DOI
10.1109/cpem68396.2026.11757011

Related papers

Millimeter-wavelength radiation from arrays of discrete high-temperature superconductor Josephson junctions

Fangfang Song, M. Levitchev, Vadim A. Markelov +3 more

Josephson junction arrays could be competitive candidates for radiation sources in the frequency range from 0.5 to 1.5 THz. This is the range where compact solid-state continuous wave sources are most lacking. We investigated the millimeter-wave radiation from arrays of high-temperature superconductor bicrystal Josephson junctions embedded in a quasi-optical resonator. The novel approach of utilizing the intrinsic resonance modes of the substrate to improve the impedance coupling between the series array of discrete Josephson junctions and the quasi-optical resonator was investigated by experiments and electromagnetic field simulations. Radiation from the arrays containing up to 536 junctions was detected at about 80 GHz and liquid nitrogen temperature using a low-noise receiver. The detected maximum radiation power of the arrays was about 50 pW and the peak voltage agreed exactly with the Josephson current–voltage relation.

Superconductor Science and Technology•Feb 22, 2010•6 citations

Metrological Study of YBCO Josephson Junction Arrays Integrated in a Fabry-Perot Resonator

A. Sosso, Domenico Andreone, V. Lacquaniti +3 more

The application of high temperature superconductor Josephson junctions to voltage metrology is promising for many reasons, beyond the evident advantage of simplified cryogenics and reduced costs of the apparatus. Owing to their intrinsic non-hysteretic behavior, arrays of shunted bicrystal YBCO junctions are particularly interesting for the realization of an AC voltage standard with quantum accuracy. Moreover, shunted bicrystal YBCO junctions arrays are advantageous because of the reduced area of the junctions, the wide range of characteristic voltages, and large critical currents. However, some specific problems arise, like possible effects related to the higher operating temperature. Furthermore, fabrication technology sets tight constraints on the design of structures for the distribution of microwave currents along the array junctions. We investigated the step properties under millimeter wave irradiation at frequencies about 75 GHz of HTS junction and arrays prepared on bicrystal substrates having grain boundaries. High sensitivity techniques were adopted to evaluate the step flatness at nV level and assess the accuracy of the step voltage. A new method that makes use of an open resonator, was implemented to irradiate the array, providing synchronization of a large number of junctions.

IEEE Transactions on Applied Superconductivity•Jun 1, 2007•9 citations

Millimeter-wave self-radiation from high-Tc Josephson junction arrays

Kiejin Lee, Ienari Iguchi, Jeha Kim +2 more

We report the strong microwave Josephson radiation from an array of high-T/sub c/ junctions on a MgO bicrystal substrate from centimeter- to millimeter-wave ranges. The dc bias current was fed to the junction array having parallel geometry with the pair of junctions shunted by superconducting loops. The configuration of bias leads was a series of interlocking dc SQUID's geometry which guaranteed the oscillation of all junctions at the same frequency. The phase differences between adjacent junctions with different I/sub c/R/sub n/ products could be controlled by an external small magnetic field. For a five-junctions array, we observed the coherent output power of about 13 pW without external magnetic flux, which was nearly five times higher than that of a single bicrystal junction. We observed the Josephson linewidth of the self-radiation in the coherent state to be less than 1 GHz by adjustment of the external flux.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•6 citations

Millimeter Wave Mixing Properties of EuBa 2Cu 3O 7-δ Bicrystal Grain Boundary Junction Arrays

Koji Tsuru, Kazunori Miyahara, Minoru Suzuki

We report the millimeter wave mixing properties of high-T c superconductor Josephson junction arrays using a waveguide-to-microstrip converter in the 100 GHz frequency range. The junction arrays consist of 3 weak links fabricated from EuBa2Cu3O7-δ thin films grown on an MgO bicrystal substrate. In these junction arrays, Shapiro steps are observed in the presence of 100 GHz irradiation at intervals of 3 times the fundamental step voltage. Millimeter wave mixing with an input local oscillator frequency of 99.142 GHz and an input signal frequency of 99.880 GHz is detected as the IF output at 738 MHz. The IF output power peaks at voltages corresponding to those of the dynamic resistance dV/ dI. A mixing conversion efficiency of -24.1 dB is obtained for a 3-junction array.

Japanese Journal of Applied Physics•Dec 1, 1996•1 citation

Optimization of the coupling of mm wave power to arrays of high-TcJosephson junctions

Alexander M. Klushin, M He, M. Levitchev +2 more

We explored high-temperature superconductor Josephson junction arrays embedded in a hemispherical Fabry-Perot resonator. We compared the characteristics of three designs of arrays to achieve steps at higher voltage with a better coupling to the millimeter wave irradiation power. With an optimal design, we achieved a maximum Josephson voltage of about 0.1V for an array of 620 bicrystal junctions at a temperature of 79.2K and a frequency of 77.465 GHz. Also steps from 0.01 V up to 0.1 V were observed. Our results showed that such circuits are challenging for applications in quantum voltage metrology. It is important to note that our quasioptical coupling method can be extended up to terahertz frequencies.

Journal of Physics Conference Series•Feb 1, 2008•8 citations

High frequency behaviour of coupled and uncoupled Josephson junctions based on high temperature superconductors

Jens Scherbel

Josephson junctions made from high temperature superconductors (HTS) are active high frequency devices which can be used as oscillators or frequency mixers in the submillimeter-wave region. The frequencies of these electromagnetic waves range from 300 GHz up to 3 THz. Up to now, this wave band is a relatively unexploited region of the electromagnetic spectrum because it is very difficult to produce and detect submillimeter-waves. However, submillimeter-wave technologies are becoming important in many practical scientific applications such as radio astronomy, atmospheric research, plasma diagnostics and THz-imaging, recently. In this work, the behaviour HTS Josephson junctions have been investigated experimentally and theoretically with the aim to THz-applications. In the first part the behaviour of intrinsic Josephson junction stacks are measured, and the possibility of phase locking is discussed by the theoretical analysis of two different shunt technologies depending on the parameter spread of the junction and the shunt parameters. It could be shown that stacks made from sputtered BSCCO layers does not act as intrinsic Josephson junction arrays because of their many micro shorts resulting from the layer growth. However, the stacks made from sputtered TBCCO show clear intrinsic Josephson junction behaviour. But their quasiparticle branches in the current-voltage characteristic deviate from the behaviour predicted by the common used RCSJ model. These branches can be discussed within a tunneling model using d-wave superconductor density of states. A temperature dependent current distribution and a zero bias anomaly was found. Furthermore, the coherent behaviour is studied for intrinsic arrays with additional side-wall shunts. The existence of thresholds of phase locking at especial junction and shunt parameters are demonstrated and discussed in regard to THz-oscillator applications. It was found that the Josephson junctions in a stack can be phase locked even if they have a parameter spread in the critical current up to 15% using a resonant shunt. In the second part of this work the mixing properties of HTS bicrystal Josephson junctions as wave guide mixers for 115 and 345 GHz have been investigated. (orig.)

•Jan 1, 2001•0 citations
High-temperature superconductor Josephson junction arrays were irradiated with millimeter-wave of approximately 70 GHz. The junction arrays were composed of 15 bicrystal YBCO junctions in series and produced DC voltage output of up to 2 mV, which was sampled by a commercial nanovoltmeter. The measured Vppof voltage fluctuations was on the order of 0.6 μV, exceeding the intrinsic fluctuation of the nanovoltmeter itself. To identify the origin of the excessive fluctuations, the phase noise and harmonic distortion of the millimeter-wave signal were analyzed and finally excluded from the major cause of the performance degradation. While millimeter-wave filtering and DC wiring of the apparatus can be improved, the results showed the feasibility of the millimeter-wave driving architecture and the noise analysis framework can be applied to development of even higher frequency drives into THz range.
Josephson junction arrays could be competitive candidates for radiation sources in the frequency range from 0.5 to 1.5 THz. This is the range where compact solid-state continuous wave sources are most lacking. We investigated the millimeter-wave radiation from arrays of high-temperature superconductor bicrystal Josephson junctions embedded in a quasi-optical resonator. The novel approach of utilizing the intrinsic resonance modes of the substrate to improve the impedance coupling between the series array of discrete Josephson junctions and the quasi-optical resonator was investigated by experiments and electromagnetic field simulations. Radiation from the arrays containing up to 536 junctions was detected at about 80 GHz and liquid nitrogen temperature using a low-noise receiver. The detected maximum radiation power of the arrays was about 50 pW and the peak voltage agreed exactly with the Josephson current–voltage relation.
The application of high temperature superconductor Josephson junctions to voltage metrology is promising for many reasons, beyond the evident advantage of simplified cryogenics and reduced costs of the apparatus. Owing to their intrinsic non-hysteretic behavior, arrays of shunted bicrystal YBCO junctions are particularly interesting for the realization of an AC voltage standard with quantum accuracy. Moreover, shunted bicrystal YBCO junctions arrays are advantageous because of the reduced area of the junctions, the wide range of characteristic voltages, and large critical currents. However, some specific problems arise, like possible effects related to the higher operating temperature. Furthermore, fabrication technology sets tight constraints on the design of structures for the distribution of microwave currents along the array junctions. We investigated the step properties under millimeter wave irradiation at frequencies about 75 GHz of HTS junction and arrays prepared on bicrystal substrates having grain boundaries. High sensitivity techniques were adopted to evaluate the step flatness at nV level and assess the accuracy of the step voltage. A new method that makes use of an open resonator, was implemented to irradiate the array, providing synchronization of a large number of junctions.
We report the strong microwave Josephson radiation from an array of high-T/sub c/ junctions on a MgO bicrystal substrate from centimeter- to millimeter-wave ranges. The dc bias current was fed to the junction array having parallel geometry with the pair of junctions shunted by superconducting loops. The configuration of bias leads was a series of interlocking dc SQUID's geometry which guaranteed the oscillation of all junctions at the same frequency. The phase differences between adjacent junctions with different I/sub c/R/sub n/ products could be controlled by an external small magnetic field. For a five-junctions array, we observed the coherent output power of about 13 pW without external magnetic flux, which was nearly five times higher than that of a single bicrystal junction. We observed the Josephson linewidth of the self-radiation in the coherent state to be less than 1 GHz by adjustment of the external flux.
We report the millimeter wave mixing properties of high-T c superconductor Josephson junction arrays using a waveguide-to-microstrip converter in the 100 GHz frequency range. The junction arrays consist of 3 weak links fabricated from EuBa2Cu3O7-δ thin films grown on an MgO bicrystal substrate. In these junction arrays, Shapiro steps are observed in the presence of 100 GHz irradiation at intervals of 3 times the fundamental step voltage. Millimeter wave mixing with an input local oscillator frequency of 99.142 GHz and an input signal frequency of 99.880 GHz is detected as the IF output at 738 MHz. The IF output power peaks at voltages corresponding to those of the dynamic resistance dV/ dI. A mixing conversion efficiency of -24.1 dB is obtained for a 3-junction array.
We explored high-temperature superconductor Josephson junction arrays embedded in a hemispherical Fabry-Perot resonator. We compared the characteristics of three designs of arrays to achieve steps at higher voltage with a better coupling to the millimeter wave irradiation power. With an optimal design, we achieved a maximum Josephson voltage of about 0.1V for an array of 620 bicrystal junctions at a temperature of 79.2K and a frequency of 77.465 GHz. Also steps from 0.01 V up to 0.1 V were observed. Our results showed that such circuits are challenging for applications in quantum voltage metrology. It is important to note that our quasioptical coupling method can be extended up to terahertz frequencies.
Josephson junctions made from high temperature superconductors (HTS) are active high frequency devices which can be used as oscillators or frequency mixers in the submillimeter-wave region. The frequencies of these electromagnetic waves range from 300 GHz up to 3 THz. Up to now, this wave band is a relatively unexploited region of the electromagnetic spectrum because it is very difficult to produce and detect submillimeter-waves. However, submillimeter-wave technologies are becoming important in many practical scientific applications such as radio astronomy, atmospheric research, plasma diagnostics and THz-imaging, recently. In this work, the behaviour HTS Josephson junctions have been investigated experimentally and theoretically with the aim to THz-applications. In the first part the behaviour of intrinsic Josephson junction stacks are measured, and the possibility of phase locking is discussed by the theoretical analysis of two different shunt technologies depending on the parameter spread of the junction and the shunt parameters. It could be shown that stacks made from sputtered BSCCO layers does not act as intrinsic Josephson junction arrays because of their many micro shorts resulting from the layer growth. However, the stacks made from sputtered TBCCO show clear intrinsic Josephson junction behaviour. But their quasiparticle branches in the current-voltage characteristic deviate from the behaviour predicted by the common used RCSJ model. These branches can be discussed within a tunneling model using d-wave superconductor density of states. A temperature dependent current distribution and a zero bias anomaly was found. Furthermore, the coherent behaviour is studied for intrinsic arrays with additional side-wall shunts. The existence of thresholds of phase locking at especial junction and shunt parameters are demonstrated and discussed in regard to THz-oscillator applications. It was found that the Josephson junctions in a stack can be phase locked even if they have a parameter spread in the critical current up to 15% using a resonant shunt. In the second part of this work the mixing properties of HTS bicrystal Josephson junctions as wave guide mixers for 115 and 345 GHz have been investigated. (orig.)