Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Measurement

Measurement of Rb atomic density with background-free optical absorption method obeying pressure-aligned theoretical modeling

Tianshi Cheng, Xiujie Fang, Zhida Huang, Shuo Sun, Yi Zhang, Bowen Sun, Jin Li

Published Mar 19, 2026• 0 citations
Publisher
DOI
10.1016/j.measurement.2026.121212

Related papers

Cross-calibration of atomic sensors for pressure metrology

Erik Frieling, Riley A. Stewart, James L. Booth +1 more

Atomic sensors have shown great promise for density and pressure metrology in the high, ultra-high, and extremely-high vacuum regimes. Specifically, the density of background gas particles in vacuum can be determined by measuring the collision rate between the particles and an ensemble of sensor atoms. This requires preparing the sensor atoms in a particular quantum state, observing the rate of changes of that state, and using the cross section coefficient for state-changing collisions to convert the rate into a corresponding density. The cross section can be known by various methods including by quantum scattering calculations using an ansatz for the interaction potential between the collision pair, by measurements of the post-collision sensor-atom momentum recoil distribution, or by empirical calibration of the sensor atom at a known density. Identifying systematic errors in the results of these methods can be aided by direct comparisons between them. Alternatively, measurements of different sensor atoms exposed to the same background gas offers another point of comparison free of the systematic errors inherent in creating a background gas at a known density. Here, we present such measurements for two sensor atoms, $^{87}$Rb and $^6$Li, and a variety of atomic and molecular background gases including H$_2$, N$_2$, Ar, Ne, Kr, and Xe. We find results consistent with, yet statistically different at the level of 3.5(5)%, from recent theoretical and experiment measurements. This work demonstrates a model-free method for transferring the primacy of one atomic standard to another sensor atom and highlights the utility of sensor-atom cross-calibration experiments to check the validity of direct measurements and theoretical predictions.

arXiv:2312.15446•Dec 24, 2023•1 citation

Determination of the Rb atomic number density in dense rubidium vapors by absorption measurements of Rb2 triplet bands

Vlasta Horvatić, D. Veža, Kay Niemax +1 more

Spectrochimica Acta Part B Atomic Spectroscopy•Dec 5, 2007•5 citations

A precise measurement method of each component gas pressures in rubidium vapor cell based on atom absorption spectra

Wei Feng, Guangzong Xiao, Xiaohu Liu +2 more

A new method and its principle are presented for measuring the each component gas pressures in Rubidium (Rb) by the analysis of absorption spectral profile. The experiment system is set up to obtain Rb absorption spectra. And then each component gas pressures in atom vapor cell is estimated. First, the relationships between transmittance of probe light, atom density and absorption cross section are introduced, and the factors which influence the absorption spectral profile and methods to measure gas pressures are given. Second, the frequency-dependence curves of transmittance and the absorption spectra are obtained through tuning the laser frequency through the Rb D1 transition. Finally, the gas pressures of Rb, N2 and He are achieved, through fitting absorption spectral profile referring to half-width and minimum transmittance value of absorption spectra. The experiment results show that gas pressures in Rb atom vapor cell can be accurately measured by absorption spectrometric methods, which will be helpful for the following study of atom vapor cell. The gas pressures of N2 and He measured by the experiments are well matched with design values. The Rb gas pressure is 30%~50% less than the saturated vapor pressure and the suppression may be due to the adsorption of the cell surfaces coated with octadecyltrichlorosilane (OTS) film.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Dec 3, 2014•0 citations

Optical alignment of 87 Rb atoms

Evgenii B. Aleksandrov, M. V. Balabas

Optics and Spectroscopy•Jul 1, 1990•2 citations

Measurement of Rb Excited States

Jarett L. Bartholomew

APS•Oct 1, 1998•0 citations

Development of a magneto optical trap for Rubidium 87

Huzifa Mohammed Ahamed Mohammed Elnour

ENGLISH ABSTRACT: A Magneto Optical Trap (MOT) is a configuration formed by three orthogonal pairs of counterpropagating circularly polarized laser beams and a magnetic field gradient. A MOT is used to cool, capture and trap large numbers of atoms in vacuum at very low temperature in K range. In this thesis the development of an experimental setup for realising a MOT of 87Rb atoms is presented. The atomic structure of Rb and the theoretical background of laser cooling and magneto optical trapping was reviewed. The influence of rubidium background pressure in the vacuum system, the laser beam size and the power and frequency on the number of the trapped atoms were studied in literature. The trapping and repumping lasers were characterised experimentally. Six circularly polarised trapping beams with equal power were formed and properly aligned to intersect at the center of the trapping cell. Two optical setups were designed and exploited to investigate and optimise the trapping beam polarisation. The repumping laser beam was successfully aligned and colinearly combined into all the trapping beams. Three different experimental setups for saturated absorption spectroscopy were developed. Saturated absorption spectra showing the hyperfine structure of both 85Rb and 87Rb isotopes were measured and are discussed. Using two saturated absorption spectroscopy setups, the frequencies of both lasers were successfully locked to the trapping and repumping transitions of 87Rb respectively. A rectangular trapping cell was designed and attached to the vacuum system. A pressure of about 10­¯7 mbar was achieved. The magnetic field coils were characterised and affixed on both sides of the cell in an anti-Helmholtz configuration. Setups for imaging and quantification of the 87Rb atoms in the MOT were designed. Finally, the procedures for demonstrating a MOT are presented. In conclusion, the current status of the project is reported, with recommendations for the future work.

•Dec 1, 2013•0 citations
Atomic sensors have shown great promise for density and pressure metrology in the high, ultra-high, and extremely-high vacuum regimes. Specifically, the density of background gas particles in vacuum can be determined by measuring the collision rate between the particles and an ensemble of sensor atoms. This requires preparing the sensor atoms in a particular quantum state, observing the rate of changes of that state, and using the cross section coefficient for state-changing collisions to convert the rate into a corresponding density. The cross section can be known by various methods including by quantum scattering calculations using an ansatz for the interaction potential between the collision pair, by measurements of the post-collision sensor-atom momentum recoil distribution, or by empirical calibration of the sensor atom at a known density. Identifying systematic errors in the results of these methods can be aided by direct comparisons between them. Alternatively, measurements of different sensor atoms exposed to the same background gas offers another point of comparison free of the systematic errors inherent in creating a background gas at a known density. Here, we present such measurements for two sensor atoms, 87^{87}87Rb and 6^66Li, and a variety of atomic and molecular background gases including H2_22​, N2_22​, Ar, Ne, Kr, and Xe. We find results consistent with, yet statistically different at the level of 3.5(5)%, from recent theoretical and experiment measurements. This work demonstrates a model-free method for transferring the primacy of one atomic standard to another sensor atom and highlights the utility of sensor-atom cross-calibration experiments to check the validity of direct measurements and theoretical predictions.
A new method and its principle are presented for measuring the each component gas pressures in Rubidium (Rb) by the analysis of absorption spectral profile. The experiment system is set up to obtain Rb absorption spectra. And then each component gas pressures in atom vapor cell is estimated. First, the relationships between transmittance of probe light, atom density and absorption cross section are introduced, and the factors which influence the absorption spectral profile and methods to measure gas pressures are given. Second, the frequency-dependence curves of transmittance and the absorption spectra are obtained through tuning the laser frequency through the Rb D1 transition. Finally, the gas pressures of Rb, N2 and He are achieved, through fitting absorption spectral profile referring to half-width and minimum transmittance value of absorption spectra. The experiment results show that gas pressures in Rb atom vapor cell can be accurately measured by absorption spectrometric methods, which will be helpful for the following study of atom vapor cell. The gas pressures of N2 and He measured by the experiments are well matched with design values. The Rb gas pressure is 30%~50% less than the saturated vapor pressure and the suppression may be due to the adsorption of the cell surfaces coated with octadecyltrichlorosilane (OTS) film.
ENGLISH ABSTRACT: A Magneto Optical Trap (MOT) is a configuration formed by three orthogonal pairs of counterpropagating circularly polarized laser beams and a magnetic field gradient. A MOT is used to cool, capture and trap large numbers of atoms in vacuum at very low temperature in K range. In this thesis the development of an experimental setup for realising a MOT of 87Rb atoms is presented. The atomic structure of Rb and the theoretical background of laser cooling and magneto optical trapping was reviewed. The influence of rubidium background pressure in the vacuum system, the laser beam size and the power and frequency on the number of the trapped atoms were studied in literature. The trapping and repumping lasers were characterised experimentally. Six circularly polarised trapping beams with equal power were formed and properly aligned to intersect at the center of the trapping cell. Two optical setups were designed and exploited to investigate and optimise the trapping beam polarisation. The repumping laser beam was successfully aligned and colinearly combined into all the trapping beams. Three different experimental setups for saturated absorption spectroscopy were developed. Saturated absorption spectra showing the hyperfine structure of both 85Rb and 87Rb isotopes were measured and are discussed. Using two saturated absorption spectroscopy setups, the frequencies of both lasers were successfully locked to the trapping and repumping transitions of 87Rb respectively. A rectangular trapping cell was designed and attached to the vacuum system. A pressure of about 10­¯7 mbar was achieved. The magnetic field coils were characterised and affixed on both sides of the cell in an anti-Helmholtz configuration. Setups for imaging and quantification of the 87Rb atoms in the MOT were designed. Finally, the procedures for demonstrating a MOT are presented. In conclusion, the current status of the project is reported, with recommendations for the future work.