Quantum computing's promise to solve complex, uncomputable problems is likely to require systems with billions of qubits. Creating an efficient interface between such a vast number of qubits and classical systems represents an enormous challenge, critical to fulfilling that promise. In this thesis, I demonstrate that the readout and control subsystems comprising this interface can be engineered in new ways that overcome current non-scalable limitations. Connecting billions of qubits to classical systems demands innovative solutions to address power dissipation, readout and control overhead, and space constraints. These issues stem from the bottleneck in the cryogenic fridge housing the quantum systems, where ultra-low temperature requirements impose space and cooling power limitations. Reducing the per-qubit load is a requirement of scale-up, and while many novel approaches have been proposed, questions remain on their effect on the qubits themselves. If future qubits have significantly higher fidelities than those available today, then far fewer are needed to achieve the same level of effectiveness. My first experiment explores this possibility by examining a measurement-only approach to topological states. Topological architectures have long promised qubits far more robust to noise compared to those of today, however engineering challenges have prevented their realisation. A measurement-only approach alleviates some of these challenges, and to validate this idea, a trivial topological state (the Aharonov-Bohm effect) is measured using a dispersive gate sensing (DGS) technique. We find that this state can be read out using DGS, with the measurement speed far surpassing that of conventional transport measurement methods. Applying DGS to other architectures also reduces their per-qubit load, as it eliminates the need for a discrete charge sensor, thereby decreasing the number of connections required for a quantum device. Billions of qubits will require billions of...
Quantum computing's promise to solve complex, uncomputable problems is likely to require systems with billions of qubits. Creating an efficient interface between such a vast number of qubits and classical systems represents an enormous challenge, critical to fulfilling that promise. In this thesis, I demonstrate that the readout and control subsystems comprising this interface can be engineered in new ways that overcome current non-scalable limitations. Connecting billions of qubits to classical systems demands innovative solutions to address power dissipation, readout and control overhead, and space constraints. These issues stem from the bottleneck in the cryogenic fridge housing the quantum systems, where ultra-low temperature requirements impose space and cooling power limitations. Reducing the per-qubit load is a requirement of scale-up, and while many novel approaches have been proposed, questions remain on their effect on the qubits themselves. If future qubits have significantly higher fidelities than those available today, then far fewer are needed to achieve the same level of effectiveness. My first experiment explores this possibility by examining a measurement-only approach to topological states. Topological architectures have long promised qubits far more robust to noise compared to those of today, however engineering challenges have prevented their realisation. A measurement-only approach alleviates some of these challenges, and to validate this idea, a trivial topological state (the Aharonov-Bohm effect) is measured using a dispersive gate sensing (DGS) technique. We find that this state can be read out using DGS, with the measurement speed far surpassing that of conventional transport measurement methods. Applying DGS to other architectures also reduces their per-qubit load, as it eliminates the need for a discrete charge sensor, thereby decreasing the number of connections required for a quantum device. Billions of qubits will require billions of...
Quantum computing promises to deliver uniquely powerful information processing machines by exploiting the quantum phenomena of superposition and entanglement. In solid-state systems, there has been significant progress in the isolation and control of the fundamental units needed to build such machines, known as qubits. However, scaling-up the number of qubits to the point where sophisticated algorithms can be performed presents considerable experimental challenges. In particular, it is becoming increasingly apparent that a new class of tools will be required to interface between fragile quantum systems, and the classical readout and control hardware of the outside world. This thesis presents experimental investigations towards the development of a scalable readout architecture for semiconductor qubit platforms. Fast readout of a GaAs-AlGaAs double quantum dot in the few-electron regime is first demonstrated via an embedded dispersive gate sensor (DGS), alleviating the burden of requiring separate charge sensors for every qubit. The sensitivity and bandwidth of this technique are extracted and benchmarked against well-established readout methods. Dispersive gate sensing of quantum point contacts (QPCs) is then presented, probing charge rearrangement within the local electrostatic environment of quasi one-dimensional channels. A low-loss, lumped-element, LC resonant circuit is also implemented for frequency multiplexed readout. The second set of experiments concern the design and characterisation of miniaturised, on-chip circulators based on the quantum Hall effect, and the quantum anomalous Hall effect. Microwaves are first capacitively coupled into edge magnetoplasmon modes in a mesoscopic GaAs-AlGaAs droplet. Non-reciprocal forward transmission comparable to off-the-shelf components is observed, which is accounted for within an interferometric picture. This circulator design is then extended to thin films of the three-dimensional topological insulator, Cr-doped (Bi,Sb)2Te3, wherein similar non-reciprocity is demonstrated in the absence of an external magnetic field.
Quantum mechanics allows for the processing of information in entirely new ways, surpassing the computational limits set by classical physics. Termed `quantum information processing', scaling this scheme relies on simultaneously increasing the number of qubits -- the fundamental unit of quantum computation -- whilst reducing their error rates. With this comes a variety of challenges, including the ability to readout the quantum state of large numbers of qubits, as well as to control their evolution in order to mitigate errors. This thesis aims to address these challenges by developing techniques for the readout and control of quantum systems. The first series of experiments focuses on the readout of GaAs/AlGaAs semiconductor quantum systems, primarily relating to the technique of dispersive gate sensing (DGS). DGS is used to probe electron transmission in an open system, a quantum point contact, demonstrating an ability to resolve characteristic features of a one-dimensional ballistic channel in the limit where transport is not possible. DGS is also used to observe anomalous signals in the potential landscape of quantum-dot defining gate electrodes. A technique for time domain multiplexing is also presented, which allows for readout resources, in the form of microwave components, to be shared between multiple qubits, increasing the capacity of a single readout line. The second series of experiments validates control techniques using trapped 171Yb+ ions. Classical error models are engineered using high-bandwidth IQ modulation of the microwave source used to drive qubit rotations. Reductions in the coherent lifetime of the quantum system are shown to match well with quantitative models. This segues in to developing techniques to understand and suppress noise in the system. This is achieved using the filter-transfer function approach, which casts arbitrary quantum control operations on qubits as noise spectral filters.
Quantum computing promises an exponential speed-up of computation compared to what is nowadays achievable with classical computers. In this way, it enables the evaluation of more complex models and the breaching of current security algorithms. For the operation of a quantum system, many questions remain to be answered. Currently, there are several quantum technologies that promise to be both reliable and scalable, two features required for large scale quantum operations. Common to all technologies is the operating temperature that needs to be close to absolute zero, i.e. below 100 mK, to suppress environment noise and allow the quantum properties to become 'visible'. In order for any quantum processor to be operated, a so-called quantum-classical interface is required for the quantum bit (qubit) read-out and control. This interface consists of various electronic blocks, such as analog-to-digital converters, digital-to-analog converters, mixers, amplifiers and a digital controller. Especially the analog blocks require effort to meet the noise and stability constraints as not to disturb the very sensitive qubits and allow reading of the tiny signals. As the qubits live in extremely deep-cryogenic temperatures, long wires interface the cryogenic with the room temperature environment, where most of the electronics is situated. However, for a scalable system, heat injection becomes a serious problem, with many wires between 300 K and sub-Kelvin. Furthermore, such amount of interconnects is challenging to mechanically place in a dilution refrigerator. Therefore, in this work, we propose to implement the electronics not at room temperature, but at a temperature much closer to the qubits, for example at 4 K. This not only reduces significantly the wiring between room temperature and the qubits, but we can also benefit from lower electronic noise at such a temperature. The operation of conventional electronics almost 200°C below its normal temperature range is not trivial as device properties alter significantly and most circuits no longer operate as intended. In CMOS processes, the main technology in the integrated electronics world, the behaviour of the transistors, required for the implementation of any circuit, deviates considerably at low temperatures. The transistor's threshold voltage goes up, the mobility increases and the subthreshold slope becomes steeper, to name just a few of these deviations. Although there are improvements in performance, there are also some counter effects, and characterization of the transistors is needed to observe the changes. Once devices are characterized at such low temperatures, new models can be built and circuits can be simulated and adapted to operate properly at cryogenic temperatures. Luckily, there are various commercially available devices that can already withstand the chills of cold. We demonstrated various commercially available devices, such as a field-programmable gate array (FPGA) implemented in a 28 nm CMOS process, to be operating without major concerns at 4~K. Its properties alter only slightly, within 5 to 10%, and all tested circuit implementations, working at 300~K, also worked at 4 K. We combined both commercially available devices, that operate 200 K below their specified temperature range, with custom designed CMOS circuits to implement a cryogenic read-out platform for spin qubits. This system comprises amplifiers, an ADC, an FPGA, voltage regulators and a clock generator. It allows to amplify the tiny signal from the qubits and digitize it directly in the FPGA in order to process the data locally at 4~K. This system is one of the first systematic attempts at operating a part of the quantum-classical interface at cryogenic temperatures and forms the basis for future systems comprising the complete electronic interface for qubits to operate at such low temperatures. One of the main problems to tackle for cryogenic electronic systems is their power consumption. Power budgets are simply limited to roughly 1 or 2 Watts at 4 K and exponentially lower at deeper cryogenic temperatures, thus limiting the size of large-scale electronic systems. Our approach of combined commercial and custom circuits will have to be steadily replaced by a single (custom) technology that meets both power and scalability constraints. One of the best candidates is CMOS, a technology that the industry has relied upon for several decades and benefits from many optimizations thanks to Moore's law.
Quantum computers have gained widespread interest as they can potentially solve problems that are intractable even for today’s supercomputers, such as the simulation of quantum systems as initially proposed by Feynman. To achieve such tremendous progress, a quantum computer relies on processing the information stored in quantum bits (qubits), the fundamental units of quantum computation, similar to the bits in a classical (i.e., non-quantum) processor. In general, a quantum processor comprising several qubits is connected through a quantum-to-classical interface consisting of classical electrical circuits for manipulating and reading out their quantum state. The accuracy of an operation on a qubit is characterized using the fidelity, which is 100 % in case of a perfect operation. In practice, a fidelity between 99 % and 99.9 % is typically achieved in today’s experiments with less than 100 qubits, limited by non-idealities in the control signals and by the implementation of the physical qubit itself. Since such qubit fidelities are too low to execute relevant quantum algorithms, quantum error correction schemes have been developed which rely on a much larger number of qubits to correct for possible errors, resulting in the need for quantum processors with thousands or millions of qubits. Solid-state qubits promise the largescale integration required to scale to millions of qubits, as they exploit the lithographic fabrication techniques borrowed from the semiconductor industry. However, state-of-theart solid-state qubits, such as transmons and single-electron spin qubits, must be typically cooled to cryogenic temperatures in a dilution refrigerator to exhibit quantum behavior. Because of the limited number of qubits (< 100) in state-of-theart solid-state quantum processors, the classical controller is currently implemented by general-purpose instruments or by tailor-made controllers operating at room temperature connected via several wires to the qubits in the cryogenic chamber. However, these systems must scale to support millions of qubits. While scaling up the underlying quantum processor is already exceptionally challenging, building the electronics required to interface such a large-scale processor is just as relevant and arduous.
There is currently a worldwide effort towards the realisation of large-scale quantum computers that exploit quantum phenomena for information processing. While these computing systems could potentially redefine the technological landscape, harnessing quantum effects is challenging due to their inherently fragile nature and the experimentally demanding environments in which they arise. In order for quantum computation to be viable it is first necessary to demonstrate the operation of two-level quantum systems (qubits) which have long coherence times, can be quickly read out, and can be controlled with high fidelity. Focusing on these key requirements, this thesis presents four experiments towards scalable solid state quantum computing using gate-defined quantum dot devices based on gallium arsenide (GaAs) heterostructures. The first experiment investigates a phonon emission process that limits the charge coherence in GaAs and potentially complicates the microwave control of multi-qubit devices. We show that this microwave analogy to Raman spectroscopy can provide a means of detecting the unique phonon spectral density created by a nanoscale device. Experimental results are compared to a theoretical model based on a non-Markovian master equation and approaches to suppressing electron-phonon coupling are discussed. The second experiment demonstrates a technique involving in-situ gate electrodes coupled to lumped-element resonators to provide high-bandwidth dispersive read-out of the state of a double quantum dot. We characterise the charge sensitivity of this method in the few-electron regime and benchmark its performance against quantum point contact charge sensors. The third experiment implements a low-loss, chip-level frequency multiplexing scheme for the readout of scaled-up spin qubit arrays. Dispersive gate-sensing is realised in combination with charge detection based on two radio frequency quantum point contacts to perform multiplexed readout of a double quantum dot in the few-electron regime. Demonstration of a 10-channel multiplexing device is achieved and limitations in scaling spin qubit readout to large numbers using multiplexed channels discussed. The final experiment ties previously presented results together by realising a micro-architecture for controlling and reading out qubits during the execution of a quantum algorithm. The basic principles of this architecture are demonstrated via the manipulation of a semiconductor qubit using control pulses that are cryogenically routed using a high-electron mobility transistor switching matrix controlled by a field programmable gate array. Finally, several technical results are also presented including the development of printed circuit board solutions to allow the high-frequency measurement of nanoscale devices at cryogenic temperatures and the design of on-chip interconnects used to suppress electromagnetic crosstalk in high-density spin qubit device architectures.
Quantum entanglement and superposition, in addition to revealing interesting physics in their own right, can be harnessed as computational resources in a machine, enabling a range of algorithms for classically intractable problems. In recent years, experiments with small numbers of qubits have been demonstrated in a range of solid-state systems, but this is far from the numbers required to realise a useful quantum computer. In addition to the qubits themselves, quantum operation requires a host of classical electronics for control and readout, and current techniques used in few-qubit systems are not scalable. This thesis presents a series of techniques for control and readout of solid-state qubits, working towards scalability by integrating classical control with the quantum technology. Two techniques for reducing the footprint associated with readout of gallium arsenide spin qubits are demonstrated. Gate electrodes, used to define the quantum dot, are also shown to be sensitive state detectors. These gate-sensors, and the more conventional Quantum Point Contacts, are then multiplexed in the frequency domain, where three-channel qubit readout and ten-channel QPC readout are demonstrated. Two types of superconducting devices are also explored. The loss in superconducting coplanar waveguide resonators is measured, and a suppression of coupling to the parasitic electromagnetic environment is demonstrated. The thesis also details software for the simulation of Josephson-junction based circuits including features beyond what is available in commercial products. Finally, an architecture for managing control of a scalable machine is proposed where classical components are distributed throughout a cryostat and cryogenic switches route control pulses to the appropriate qubits. A simple implementation of the architecture is demonstrated that incorporates a double quantum dot, a gallium arsenide switch matrix, frequency multiplexed readout, and cryogenic classical computation.