Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE MTT-S International Wireless Symposium (IWS)

Dielectric Waveguide-Integrated Rydberg Superheterodyne Receiver for Omnidirectional Electrometry

Xu Li, Yiming Zhang, Lei Hu

Published May 19, 2025• 0 citations
Publisher

Abstract

This study demonstrates a compact Rydberg-based electric field sensor with integrated local oscillator (LO) generation through a dielectric waveguide (DW) architecture. By embedding a Rydberg vapor cell within a transparent waveguide, we achieve monolithic LO synthesis while overcoming the angular constraints of conventional metallic waveguide systems, enabling full 360° spatial detection. Numerical simulations confirm the omnidirectional response characteristics across varying incident angles. Experimental validation using a 19.626 GHz LO and 19.62609 GHz signal frequency reveals successful down-conversion to a 90 kHz intermediate frequency via Rydberg atomic mixing, with modulation depth linearly proportional to the incident field strength. This waveguide-integrated design establishes a new paradigm for antenna measurement systems, particularly in scenarios requiring omnidirectional sensing capabilities.

DOI
10.1109/iws65943.2025.11177744

Related papers

Near-Field Focusing Array-Integrated Rydberg Atomic Superheterodyne Receiver with Phase-Coherent Enhancement

Y Yan, Xu Li, Yan-Qi Yi +2 more

This paper presents a high-sensitivity Rydberg atomic receiver integrated with a Near-Field Focusing (NFF) array to optimize local oscillator (LO) delivery. Unlike conventional metallic enhancers that cause electromagnetic shielding, the NFF array focuses LO energy from a distance, preserving the sensor's intrinsic omnidirectionality. The 4 × 4 U-slot array operates at 2.84 GHz, tailoring the LO phase into a quasi-plane wave to mitigate atomic dephasing. Quantum simulations confirm a linear response for signal fields from 0.01 to$0.08 \mathrm{V} / \mathrm{m}$, aligning with theoretical EIT modulation. This architecture achieves localized high-gain enhancement and phase-consistent wavefront correction, establishing a novel paradigm for compact, high-performance quantum RF sensing.

IEEE International Symposium on Electromagnetic Compatibility•Apr 24, 2026•0 citations

Embedding a Rydberg Atom-Based Sensor Into an Antenna for Phase and Amplitude Detection of Radio-Frequency Fields and Modulated Signals

Matthew T. Simons, Abdulaziz H. Haddab, Joshua A. Gordon +2 more

We demonstrate a Rydberg atom-based sensor embedded in a parallel-plate waveguide (PPWG) for amplitude and phase detection of a radio-frequency (RF) electric field. This embedded atomic sensor is also capable of receiving modulated communications signals. In this configuration, the PPWG antenna serves two functions. First, the PPWG antenna acts as a source for a local oscillator (LO) field. The LO is required to use an atomic vapor cell (a glass cell containing a Rydberg atom vapor) as a Rydberg atom-based mixer, which detects the amplitude and phase of a second RF field incident from some remote location. The second function of the PPWG antenna is to capture the RF field arriving from a remote location and concentrate it at the location of the atomic vapor cell for detection. To demonstrate this, we show several examples of phase and amplitude measurements of an RF field with the embedded Rydberg-atom sensor. We also demonstrate the discrimination of the polarization of an RF field and the ability to receive phase-modulated carrier communications signals with this integrated atomic sensor. Embedding the atomic sensor in an antenna allows for the full characterization of a radio frequency field, in that the magnitude, phase, and polarization of an RF field can be measured with one compact integrated quantum-based sensor. Furthermore, the embedded sensor head allows one to easily vary the LO in order to maximize the ability to measure phase and amplitude of the field or modulated signal.

IEEE Access•Jan 1, 2019•99 citations

Continuously tunable radio frequency electrometry with Rydberg atoms

Jinlian Hu, Huaqiang Li, Rong Song +4 more

We demonstrate a continuously tunable electric field measurement based on the far off-resonant AC stark effect in a Rydberg atomic vapor cell. In this configuration, a strong far off-resonant field, denoted as a local oscillator (LO) field, acts as a gain to shift the Rydberg level to a high sensitivity region. An incident weak signal field with a few hundreds of kHz difference from the LO field is mixed with the LO field in the Rydberg system to generate an intermediate frequency signal, which is read out by Rydberg electromagnetically induced transparency (Rydberg-EIT) spectroscopy. Not like resonant EIT-Autler–Townes spectra, we realize the electric field measurement of the signal frequency from 2 to 5 GHz using a single Rydberg state. The detectable field strength is down to 2.25 μV/cm with sensitivity of the electrometry 712 nV cm−1 Hz−1/2, and a linear dynamic range is over 65 dB. The detectable field strength is comparable with a resonant microwave-dressed Rydberg heterodyne receiver using the same system, which is 0.96 μV/cm with sensitivity of 304 nV cm–1 Hz−1/2. We also show the system has an inherent polarization selectivity feature. Our method can provide high sensitivity of electric field measurement and be extended to arbitrary frequency measurements.

arXiv:2201.10068•Applied Physics Letters•Jul 4, 2022•107 citations

Broadband microwave electric field measurement based on a planar dipole antenna as the local oscillator source

Jiwang Chai, Guixiang Liu, Muhan Zhang +5 more

We propose a superheterodyne microwave electric field measurement scheme based on Rydberg atoms that utilizes a planar dipole antenna as the local oscillator source. By designing a two-dimensional asymmetric dipole antenna, broadband microwave near-field radiation is achieved in the region of 1.7 GHz-9 GHz with return loss less than −10 dB, and the feasibility of using a planar antenna as the local oscillator source has been verified through simulations and experiments. In the experiments, high-sensitivity electric field measurements are performed by using near-field radiation from the planar antenna as local oscillator field for three resonant frequencies, 3.999 GHz, 5.048 GHz, and 7.981 GHz, with an optimal sensitivity of 3.16 µV/cm/Hz1/2. Comparative experiments with a horn antenna as the local oscillator source show that the planar antenna can achieve equivalent measurement sensitivity. Continuous-frequency electric field measurements are also investigated with a planar antenna in the frequency range of 2.5 GHz-9 GHz, and a minimum detectable field strength ranging from 3.16 µV/cm to 25.95 µV/cm is achieved. Our findings provide an alternative design approach for compact superheterodyne Rydberg atomic sensors.

Optics Express•Jul 21, 2025•1 citation

Rydberg Atom-Based Sensors: Principles, Recent Advances, and Applications

Dinelka Somaweera, Amer Abdulghani, Ambali Alade Odebowale +7 more

Rydberg atoms are neutral atoms excited to high principal quantum number states, which endows them with exaggerated properties such as large electric dipole moments, long lifetimes, and extreme sensitivity to external electromagnetic fields. These characteristics form the foundation of Rydberg atom-based sensors, an emerging class of quantum devices capable of optically detecting electric fields across frequencies from DC to the terahertz regime. Rydberg-based electrometry operates through both Autler–Townes (AT) splitting of resonant Rydberg transitions and Stark-shift measurements for high-frequency or far-detuned fields, enabling broadband field sensing from DC to the THz regime. Using ladder-type electromagnetically induced transparency (EIT) and AT splitting, these sensors enable non-invasive, SI-traceable measurements of field amplitude, frequency, phase, and polarization. Recent developments have demonstrated broadband electric field probes, voltage calibration standards, and compact RF receivers based on thermal vapor cells and integrated photonic architectures. Furthermore, innovations in multi-photon EIT, superheterodyne readout, and multi wave mixing have expanded the dynamic range and bandwidth of Rydberg-based electrometry. Despite challenges related to environmental perturbations, linewidth broadening, and laser stabilization, ongoing advances in atomic control, hybrid photonic integration, and EIT-based readout promise scalable, chip-compatible sensors. This review summarizes the physical principles, experimental progress, and emerging applications of Rydberg atom-based sensing, emphasizing their potential for next generation quantum metrology, wireless communication, and precision field mapping.

Photonics•Dec 12, 2025•14 citations

A miniaturized wideband Rydberg-atom superheterodyne receiver based on a microstrip balun

Jiwang Chai

Abstract Ultra-wideband, miniaturized, and integrable local oscillator sources remain a key challenge for Rydberg-atom superheterodyne receivers. Here we demonstrate a 1–40 GHz Rydberg-atom receiver that uses a 76.3-mm-long, 1.6-mm-thick microstrip balun as the local oscillator. A load terminating the output port is used to enhance the balun near field and enable efficient coupling to the atoms. High-sensitivity electric field measurements based on the microstrip balun local oscillator are experimentally demonstrated at 9.94 and 19.63 GHz, achieving a lowest tested field of 0.79 and 0.49 µV/cm, respectively, compared with 0.40 and 0.39 µV/cm for a horn-antenna local oscillator. By combining resonant and off-resonant superheterodyne measurements across nine Rydberg transitions, we further demonstrate continuous-frequency electric field measurements from 1 to 40 GHz. These results establish the microstrip balun as a compact, broadband local oscillator source for integrated atomic receivers.

•Jul 15, 2026•0 citations
This study demonstrates a compact Rydberg-based electric field sensor with integrated local oscillator (LO) generation through a dielectric waveguide (DW) architecture. By embedding a Rydberg vapor cell within a transparent waveguide, we achieve monolithic LO synthesis while overcoming the angular constraints of conventional metallic waveguide systems, enabling full 360° spatial detection. Numerical simulations confirm the omnidirectional response characteristics across varying incident angles. Experimental validation using a 19.626 GHz LO and 19.62609 GHz signal frequency reveals successful down-conversion to a 90 kHz intermediate frequency via Rydberg atomic mixing, with modulation depth linearly proportional to the incident field strength. This waveguide-integrated design establishes a new paradigm for antenna measurement systems, particularly in scenarios requiring omnidirectional sensing capabilities.
This paper presents a high-sensitivity Rydberg atomic receiver integrated with a Near-Field Focusing (NFF) array to optimize local oscillator (LO) delivery. Unlike conventional metallic enhancers that cause electromagnetic shielding, the NFF array focuses LO energy from a distance, preserving the sensor's intrinsic omnidirectionality. The 4 × 4 U-slot array operates at 2.84 GHz, tailoring the LO phase into a quasi-plane wave to mitigate atomic dephasing. Quantum simulations confirm a linear response for signal fields from 0.01 to0.08V/m0.08 \mathrm{V} / \mathrm{m}0.08V/m, aligning with theoretical EIT modulation. This architecture achieves localized high-gain enhancement and phase-consistent wavefront correction, establishing a novel paradigm for compact, high-performance quantum RF sensing.
We demonstrate a Rydberg atom-based sensor embedded in a parallel-plate waveguide (PPWG) for amplitude and phase detection of a radio-frequency (RF) electric field. This embedded atomic sensor is also capable of receiving modulated communications signals. In this configuration, the PPWG antenna serves two functions. First, the PPWG antenna acts as a source for a local oscillator (LO) field. The LO is required to use an atomic vapor cell (a glass cell containing a Rydberg atom vapor) as a Rydberg atom-based mixer, which detects the amplitude and phase of a second RF field incident from some remote location. The second function of the PPWG antenna is to capture the RF field arriving from a remote location and concentrate it at the location of the atomic vapor cell for detection. To demonstrate this, we show several examples of phase and amplitude measurements of an RF field with the embedded Rydberg-atom sensor. We also demonstrate the discrimination of the polarization of an RF field and the ability to receive phase-modulated carrier communications signals with this integrated atomic sensor. Embedding the atomic sensor in an antenna allows for the full characterization of a radio frequency field, in that the magnitude, phase, and polarization of an RF field can be measured with one compact integrated quantum-based sensor. Furthermore, the embedded sensor head allows one to easily vary the LO in order to maximize the ability to measure phase and amplitude of the field or modulated signal.
We demonstrate a continuously tunable electric field measurement based on the far off-resonant AC stark effect in a Rydberg atomic vapor cell. In this configuration, a strong far off-resonant field, denoted as a local oscillator (LO) field, acts as a gain to shift the Rydberg level to a high sensitivity region. An incident weak signal field with a few hundreds of kHz difference from the LO field is mixed with the LO field in the Rydberg system to generate an intermediate frequency signal, which is read out by Rydberg electromagnetically induced transparency (Rydberg-EIT) spectroscopy. Not like resonant EIT-Autler–Townes spectra, we realize the electric field measurement of the signal frequency from 2 to 5 GHz using a single Rydberg state. The detectable field strength is down to 2.25 μV/cm with sensitivity of the electrometry 712 nV cm−1 Hz−1/2, and a linear dynamic range is over 65 dB. The detectable field strength is comparable with a resonant microwave-dressed Rydberg heterodyne receiver using the same system, which is 0.96 μV/cm with sensitivity of 304 nV cm–1 Hz−1/2. We also show the system has an inherent polarization selectivity feature. Our method can provide high sensitivity of electric field measurement and be extended to arbitrary frequency measurements.
We propose a superheterodyne microwave electric field measurement scheme based on Rydberg atoms that utilizes a planar dipole antenna as the local oscillator source. By designing a two-dimensional asymmetric dipole antenna, broadband microwave near-field radiation is achieved in the region of 1.7 GHz-9 GHz with return loss less than −10 dB, and the feasibility of using a planar antenna as the local oscillator source has been verified through simulations and experiments. In the experiments, high-sensitivity electric field measurements are performed by using near-field radiation from the planar antenna as local oscillator field for three resonant frequencies, 3.999 GHz, 5.048 GHz, and 7.981 GHz, with an optimal sensitivity of 3.16 µV/cm/Hz1/2. Comparative experiments with a horn antenna as the local oscillator source show that the planar antenna can achieve equivalent measurement sensitivity. Continuous-frequency electric field measurements are also investigated with a planar antenna in the frequency range of 2.5 GHz-9 GHz, and a minimum detectable field strength ranging from 3.16 µV/cm to 25.95 µV/cm is achieved. Our findings provide an alternative design approach for compact superheterodyne Rydberg atomic sensors.
Rydberg atoms are neutral atoms excited to high principal quantum number states, which endows them with exaggerated properties such as large electric dipole moments, long lifetimes, and extreme sensitivity to external electromagnetic fields. These characteristics form the foundation of Rydberg atom-based sensors, an emerging class of quantum devices capable of optically detecting electric fields across frequencies from DC to the terahertz regime. Rydberg-based electrometry operates through both Autler–Townes (AT) splitting of resonant Rydberg transitions and Stark-shift measurements for high-frequency or far-detuned fields, enabling broadband field sensing from DC to the THz regime. Using ladder-type electromagnetically induced transparency (EIT) and AT splitting, these sensors enable non-invasive, SI-traceable measurements of field amplitude, frequency, phase, and polarization. Recent developments have demonstrated broadband electric field probes, voltage calibration standards, and compact RF receivers based on thermal vapor cells and integrated photonic architectures. Furthermore, innovations in multi-photon EIT, superheterodyne readout, and multi wave mixing have expanded the dynamic range and bandwidth of Rydberg-based electrometry. Despite challenges related to environmental perturbations, linewidth broadening, and laser stabilization, ongoing advances in atomic control, hybrid photonic integration, and EIT-based readout promise scalable, chip-compatible sensors. This review summarizes the physical principles, experimental progress, and emerging applications of Rydberg atom-based sensing, emphasizing their potential for next generation quantum metrology, wireless communication, and precision field mapping.
Abstract Ultra-wideband, miniaturized, and integrable local oscillator sources remain a key challenge for Rydberg-atom superheterodyne receivers. Here we demonstrate a 1–40 GHz Rydberg-atom receiver that uses a 76.3-mm-long, 1.6-mm-thick microstrip balun as the local oscillator. A load terminating the output port is used to enhance the balun near field and enable efficient coupling to the atoms. High-sensitivity electric field measurements based on the microstrip balun local oscillator are experimentally demonstrated at 9.94 and 19.63 GHz, achieving a lowest tested field of 0.79 and 0.49 µV/cm, respectively, compared with 0.40 and 0.39 µV/cm for a horn-antenna local oscillator. By combining resonant and off-resonant superheterodyne measurements across nine Rydberg transitions, we further demonstrate continuous-frequency electric field measurements from 1 to 40 GHz. These results establish the microstrip balun as a compact, broadband local oscillator source for integrated atomic receivers.