Scalable Microwave SQUID Multiplexer Readout Architecture for TES-Based THz Security Camera
Matthias Schmelz, Erik Heinz, Katja Peiselt, Gabriel Zieger, Oliver Brandel, Detlef Born, J. Kunert, Michael Siegel, V. Zakosarenko, Matthias Meyer, Ronny Stolz
In this article, we have developed a scalable superconducting quantum interference device (SQUID)-based microwave multiplexer (µMUX) readout architecture adapted for arrays of transition edge sensors (TESs) to be exploited in a terahertz security camera. The camera system combines a scanning optics together with a 128-pixel TES array and aims for security gate operations with a standoff detection distance of up to 25 m. The developed frequency-domain µMUX is used to read out all feed-horn-coupled TESs based on aluminum thermistors, with noise limited by intrinsic TES noise. Both the TESs and µMUXs are operated in a compact cryostat with a base temperature of about 0.9 K. The µMUX has been fabricated in the cross-type$\text{Nb}/ \text{AlO}\_{\rm{x}}/ \text{Nb}$Josephson junction process developed at the Leibniz Institute of Photonic Technology and incorporates high-quality superconducting thin-film resonators with resonant frequencies in the range of 5–6 GHz. An accordingly implemented field-programmable-gate-array-based readout electronics enables the simultaneous and continuous real-time readout of 128 rf-SQUIDs, including a flux ramp modulation scheme. In operation with the aluminum TES, we achieved a dark noise equivalent power of about$2.5\; \text{fW}/ \text{Hz}^{1/ 2}$while providing a TES readout rate of 3.75 kHz, necessary for a video frame rate of 25 Hz of the security camera.
In this article, we have developed a scalable superconducting quantum interference device (SQUID)-based microwave multiplexer (µMUX) readout architecture adapted for arrays of transition edge sensors (TESs) to be exploited in a terahertz security camera. The camera system combines a scanning optics together with a 128-pixel TES array and aims for security gate operations with a standoff detection distance of up to 25 m. The developed frequency-domain µMUX is used to read out all feed-horn-coupled TESs based on aluminum thermistors, with noise limited by intrinsic TES noise. Both the TESs and µMUXs are operated in a compact cryostat with a base temperature of about 0.9 K. The µMUX has been fabricated in the cross-typeNb/AlO_x/NbJosephson junction process developed at the Leibniz Institute of Photonic Technology and incorporates high-quality superconducting thin-film resonators with resonant frequencies in the range of 5–6 GHz. An accordingly implemented field-programmable-gate-array-based readout electronics enables the simultaneous and continuous real-time readout of 128 rf-SQUIDs, including a flux ramp modulation scheme. In operation with the aluminum TES, we achieved a dark noise equivalent power of about2.5fW/Hz1/2while providing a TES readout rate of 3.75 kHz, necessary for a video frame rate of 25 Hz of the security camera.
Transition Edge Sensors (TESs) are highly sensitive cryogenic detectors widely used in astronomy, high-energy physics and nuclear radiation detection. As TES is increasingly deployed in large-scale arrays to improve sensitivity and effective collecting area, multiplexed readout becomes essential for reducing system complexity. Microwave SQUID multiplexing (μMUX) technology combining superconducting resonators with radio-frequency superconducting quantum interference devices (RF-SQUIDs), represents a state-of-the-art solution. In this work, a room-temperature readout prototype for TES μMUX readout was designed. The system features a scalable two-stage architecture, including a highly integrated, chassis-independent front-end signal processing module and back-end event-reconstruction module. A high-frequency-resolution frequency-comb signal generation method with real-time, per-tone frequency and phase tunability was developed. In addition, optimization of the firmware implementation effectively overcomes the computational-resource bottleneck of the Field Programmable Gate Array (FPGA). The prototype supports autonomous frequency sweeping, parameter diagnostics, and online event reconstruction. Self-test shows S 21 phase noise better than −110 dBc/Hz at −30 dBm, remaining stable with increasing channel count. Joint tests with a μMUX cryogenic system successfully captured the RF-SQUID response and achieved an equivalent noise current of 44 pA/√Hz referred to the TES, validating the prototype as a practical solution of the room-temperature system for TES μMUX readout.
Superconducting transition-edge sensors (TESs) with high sensitivity can detect electromagnetic wave radiations from millimeter/submillimeter, optical to x/γ rays, and have been successfully used in many fields. To improve detection efficiency and sensitivity, large-scale TES arrays are required in combination with multiplexing readout electronics. Compared to other multiplexing schemes, microwave SQUID multiplexing (μMUX), consisting of high-quality microwave superconducting resonators and RF SQUIDs, is most suitable since it provides a wider bandwidth (GHz) and consequently higher multiplexing factor. We designed two types of circuits with different mutual inductances (MT) between the resonator and the RF SQUID: 2.3 pH for the weak-coupling channel and 6.5 pH for the strong- coupling channel. The resonator and RF SQUID washers made of 150 nm Nb are first fabricated by magnetron-sputtering and reactive ion etching (RIE), followed by deposition of Nb/Al-AlOx/Nb trilayer and definition of the Josephson junctions of the RF SQUIDs. This work presents a μMUX demonstration chip with five channels with Q1values of 787 and 3626, and the measured frequency shifts (Δfpp) of ∼500 kHz and 4 MHz for the weak- and strong-coupling channels, respectively. The open-loop equivalent noise current, obtained from the measured phase noise and resonator responsivity, is ∼80 pA/ √Hz with the strong-coupling channel.
We report very-low-noise, fast-response, middle-scale multiplexing in a microwave superconducting quantum interference device multiplexer (MW-Mux) as a transition-edge sensor (TES) readout. Our MW-Mux is able to read 40 channels with 500 kHz sampling and has a low readout noise of 0.9 μΦ0/Hz (where Φ0 is the magnetic flux quantum), equivalent to 9 pA/Hz. By contrast, a multiplexer of less than 10 pixels with 500 kHz sampling and ∼2 μΦ0/Hz readout noise has so far been reported in the literature. Owing to the 500 kHz sampling, our MW-Mux exhibits a fast response to detect a TES pulse with a rise time around 12 μs. We demonstrated simultaneous readout of 38 pixels from an array of x-ray TES microcalorimeters. The measured full-width values at half-maximum spectral resolution ranged from 2.79 to 4.56 eV, with a median value of 3.30 eV at 5.9 keV, including a ∼10% contribution of readout noise, i.e., 0.9–1.7 eV.
Superconducting transition-edge sensors (TESs) are highly sensitive detectors and can detect electromagnetic wave radiations from millimeter/submillimeter, optical to 𝑥/γrays, suitable for cosmology, astrophysics, quantum information, and biosensing. In principle, thousands of TESs even more are required to enhance the detection efficiency for large-scale survey. Among other multiplexing schemes, microwave SQUID multiplexer (μMUX), consisting of resonators and RF SQUIDs, has a bandwidth of several GHz, thus multiplexing factor on the order of thousands, more suitable for readout of large TES arrays. We designed and fabricated superconducting coplanar waveguide (CPW) resonators with a high qualityfactor and second-order gradient RF SQUID with two inductive coupling structures respectively. Then, we optimized the critical current density of the Josephson junction and measured the mutual inductance parameters of the second-order gradient structure SQUID, which are consistent with the simulation results. Finally, we fabricated a cryogenic μMUX chip based on RF SQUID and resonator. We discussed the results of the development of μMUX in more detail.
Abstract A microwave SQUID multiplexer ( μ MUX) with a high multiplexing factor is a promising readout approach for large-scale superconducting transition-edge sensor (TES) bolometer arrays. This paper reports on the characteristics of 16-channel μ MUX prototype chips and a 60-channel readout module developed to read out TES bolometers for the Ali cosmic microwave background polarization telescope (AliCPT). We designed two different coupling structures between the resonator and the radio-frequency superconducting interference device: design A with a mutual inductance ( M T ) of 2.3 pH and design B with an M T of 6.5 pH. For design A, the mean resonator bandwidth ( Δ f BW ) and peak-to-peak frequency shift ( Δ f pp ) are approximately 610 kHz and 290 kHz, respectively. The measured mean open-loop current noise is less than 40 pA / Hz . Preliminary results indicate that crosstalk between adjacent channels is below 1% in our design A μ MUX chip. A measured channel with design B shows a Δ f BW of 586 kHz and a current noise of 33 pA / Hz , similar to the design A channels. In comparison, the Δ f pp of 803 kHz is much larger than the design A channels due to a larger M T . The readout module, consisting of two design A chips and two design B chips, shows 60 resonances, corresponding to a yield of 94%. In the future, we will place 32 design A channels within the same chip dimension to increase the channel density and build a larger readout module suitable for AliCPT TES arrays.
To enable the next-generation of bolometric cameras, we are developing the microwave SQUID multiplexer (μMUX). Upcoming receivers such as Simons Observatory, CCAT-prime, BICEP array, Ali-CPT, and CMB-S4 plan to instrument focal planes with 50,000-500,000 sensors. Sensor count is achieved by tiling many 150 mm-diameter densely packed detector arrays into these focal planes. The fabrication and quality of large-format bolometer arrays has been demonstrated and is now mature. In contrast, the readout technology required for next-generation receivers needs development. The sensitivity, low cross-talk, high multiplexing density, and small component size make the μMUX well-suited for this goal. In this approach, the TES signal modulates the inductance of an rf-SQUID that loads a high-Q microwave resonator. The coupled signal therefore modulates the microwave resonance frequency, which may be read out using homodyne techniques. By coupling each resonator to the same microwave feedline, many detectors can be read out on a single coaxial cable pair. The multiplexing density is in practice limited by signal bandwidth, allowable cross-talk, and the digitization bandwidth of room-temperature readout electronics. We present the design and performance of a scalable 64-channel multiplexer chip optimized for bolometric applications. We utilize a new quarter wave resonator design that increases the physical linear density by a factor of two, therefore achieving a smaller footprint for simplified detector packaging. Measurements of this design show 100 kHz resonator bandwidth, uniform 1.8 MHz frequency spacing, and an input referred current noise of 35 pA/√Hz that is well below the level of an optimized, background-limited TES bolometer. Using 8 daisy-chained and frequency scaled chips, we create a 512-channel multiplexer and use it to readout a 512 TES-bolometer array. We present the results of this large-scale μMUX demonstration including system yield, signal cross-talk, and an analysis of noise in various TES bias configurations. The result demonstrates the multiplexing density required to read out 2,000 sensors between 4-8 GHz.