Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

qConnect: Increasing Qubit Connectivity in Quantum Computing Fabric Using Active Transmission Lines

Sasan Razmkhah, Pascal Febvre, Massoud Pedram

Published Jan 27, 2025• 1 citation
Publisher

Abstract

We present a novel approach for tunable superconductor microwave transmission lines and resonators that can be integrated on-chip using standard Al or Nb-based fabrication processes. By leveraging the nonlinear inductance of a Josephson junction, the impedance and, consequently, the resonance frequency of the lines can be adjusted via a small DC signal. This signal is inductively coupled to a superconducting quantum interference device loop, with the circuit designed to remain open at microwave frequencies, effectively preventing energy leakage. The simplicity and tunability of this design make it adaptable to various applications. In this work, we demonstrate the multiplexing capability of such design for use in dynamic connections between control circuits and qubits, as well as dynamic routing in quantum circuits.

DOI
10.1109/tasc.2025.3534184

Related papers

Tunable superconducting transmissionline resonator for qubit coupling

Martin Sandberg

In this licentiate thesis design, fabrication, and measurements of tunable superconducting microwave transmission line resonators are described. The resonators are of quarter wavelength type were the tuning is achieved by changing one of the boundary conditions of the resonator through a tunable impedance. As tunable impedance the Josephson inductance in form of SQUIDs is used. The Josephson inductance can then be tuned by applying a magnetic field to the SQUID loop. A tuning range of 750 MHz for a 5 GHz resonator is achieved, and as a figure of merit it can be tuned over 200 line widths. The purpose of the tunable resonators is to use them for dynamic coupling of superconducting quantum bits, this requires that the resonators can be tuned fast on the timescale of the resonator-qubit coupling. To measure tuning speeds faster then the ring up time of the resonators a method that measures the leakage of energy out of a detuned resonator was developed. With this method a frequency shift of the energy stored in the resonator can be measured. A detuning of 330 MHz in less than 10 ns is demonstrated for a 4.5 GHz resonator with a quality factor of 10$^4$. Working in the few photon limit indicates that the devices can be used to change the frequency of individual photons, this is however still to be demonstrated. As a part of this work the dressed states of a superconducting charge qubit was also studied.

•Jan 1, 2008•0 citations

Compacted tunable split-ring resonators

A. Vidiborskiy, V. P. Koshelets, L. V. Filippenko +2 more

We propose tunable superconducting split-ring resonators (SRRs) employing nonlinear Josephson inductance. A fraction of SRR is replaced by Nb-AlOx-Nb Josephson tunnel junctions connected in parallel and forming a superconducting quantum interference device, whose inductance is sensitive to the external dc magnetic field. Due to the lumped nature of the Josephson inductance, the SRR can be made very compact, and its resonance frequency can be tuned by applying magnetic field. We present the model, results of extensive electromagnetic-simulation and experimental data for the SRR weakly coupled to a transmission line within frequency range of 11–13 GHz.

arXiv:1308.4891•Applied Physics Letters•Oct 14, 2013•6 citations

A flux-tunable YBa2Cu3O7 quantum interference microwave circuit

Kevin Uhl, Daniel Hackenbeck, Christoph Füger +3 more

Josephson microwave circuits are essential for the currently flourishing research on superconducting technologies, such as quantum computation, quantum sensing, and microwave signal processing. To increase the possible parameter space for device operation with respect to the current standards, many materials for superconducting circuits are under active investigation. Here, we present the realization of a frequency-tunable, weakly nonlinear Josephson microwave circuit made of the high-temperature cuprate superconductor YBa2Cu3O7 (YBCO), a material with a high critical temperature and a very high critical magnetic field. An in situ frequency-tunability of ∼300 MHz is achieved by integrating a superconducting quantum interference device (SQUID) into the circuit based on Josephson junctions directly written with a helium ion microscope (HIM). Our results demonstrate that YBCO-HIM-SQUID microwave resonators are promising candidates for quantum sensing and microwave technology applications.

Applied Physics Letters•May 1, 2023•5 citations

A tunable coupler for superconducting microwave resonators using a nonlinear kinetic inductance transmission line

Clint Bockstiegel, Yiwen Wang, Michael R. Vissers +4 more

We present a tunable coupler scheme that allows us to tune the coupling strength between a feedline and a superconducting resonator in situ over a wide range. In this scheme, we shunt the feedline with a 50-Ω lumped-element nonlinear transmission line made from a 20 nm NbTiN film. By injecting a DC current, the nonlinear kinetic inductance changes and the effective impedance shunting the resonator periodically varies from a short to an open, which tunes the coupling strength and coupling quality factor Qc. We have demonstrated Qc tuning over a factor of 40, between Qc∼5.5×104 and Qc∼2.3×106, for a 4.5 GHz resonator by applying a DC current less than 3.3 mA. Our tunable coupler scheme is easy to implement and may find broad applications in superconducting detector and quantum computing/information experiments.

Applied Physics Letters•May 30, 2016•25 citations

A fast and large bandwidth superconducting variable coupler

H.-S. Chang, K. J. Satzinger, Y. P. Zhong +8 more

Variable microwave-frequency couplers are highly useful components in classical communication systems and likely will play an important role in quantum communication applications. Conventional semiconductor-based microwave couplers have been used with superconducting quantum circuits, enabling, for example, the in situ measurements of multiple devices via a common readout chain. However, the semiconducting elements are lossy and furthermore dissipate energy when switched, making them unsuitable for cryogenic applications requiring rapid, repeated switching. Superconducting Josephson junction-based couplers can be designed for dissipation-free operation with fast switching and are easily integrated with superconducting quantum circuits. These enable on-chip, quantum-coherent routing of microwave photons, providing an appealing alternative to semiconductor switches. Here, we present and characterize a chip-based broadband microwave variable coupler, tunable over 4–8 GHz with over 1.5 GHz instantaneous bandwidth, based on the superconducting quantum interference device with two parallel Josephson junctions. The coupler is dissipation-free and features large on-off ratios in excess of 40 dB, and the coupling can be changed in about 10 ns. The simple design presented here can be readily integrated with superconducting qubit circuits and can be easily generalized to realize a four- or more port device.

arXiv:2011.09442•Applied Physics Letters•Dec 14, 2020•10 citations

Superconducting Resonators with Voltage-Controlled Frequency and Nonlinearity

William M. Strickland, Bassel Heiba Elfeky, Joseph O’Connell Yuan +6 more

Voltage-tunable superconductor-semiconductor devices offer a unique platform to realize dynamic tunability in superconducting quantum circuits. By galvanically connecting a gated $\mathrm{In}\mathrm{As}$-$\mathrm{Al}$ Josephson junction to a coplanar waveguide resonator, we demonstrate the use of a superconducting element with wideband gate tunability. We show that the resonant frequency is controlled via a gate-tunable Josephson inductance and that the nonlinearity of the $\mathrm{In}\mathrm{As}$-$\mathrm{Al}$ junction is nondissipative as is the case with conventional ${\mathrm{Al}\mathrm{O}}_{\mathrm{x}}\text{-Al}$ junctions. As the gate voltage is decreased, the inductive participation of the junction increases up to $44\mathrm{%}$, resulting in the resonant frequency being tuned by over $2\phantom{\rule{0.2em}{0ex}}\mathrm{GHz}$. Utilizing the wide tunability of the device, we demonstrate that two resonant modes can be adjusted such that they strongly hybridize, exhibiting an avoided-level crossing with a coupling strength of $51\phantom{\rule{0.2em}{0ex}}\mathrm{MHz}$. Implementing such voltage-tunable resonators is the first step toward realizing wafer-scale continuous voltage control in superconducting circuits for qubit-qubit coupling, quantum limited amplifiers, and quantum memory platforms.

arXiv:2210.02491•Physical Review Applied•Mar 7, 2023•30 citations
We present a novel approach for tunable superconductor microwave transmission lines and resonators that can be integrated on-chip using standard Al or Nb-based fabrication processes. By leveraging the nonlinear inductance of a Josephson junction, the impedance and, consequently, the resonance frequency of the lines can be adjusted via a small DC signal. This signal is inductively coupled to a superconducting quantum interference device loop, with the circuit designed to remain open at microwave frequencies, effectively preventing energy leakage. The simplicity and tunability of this design make it adaptable to various applications. In this work, we demonstrate the multiplexing capability of such design for use in dynamic connections between control circuits and qubits, as well as dynamic routing in quantum circuits.
In this licentiate thesis design, fabrication, and measurements of tunable superconducting microwave transmission line resonators are described. The resonators are of quarter wavelength type were the tuning is achieved by changing one of the boundary conditions of the resonator through a tunable impedance. As tunable impedance the Josephson inductance in form of SQUIDs is used. The Josephson inductance can then be tuned by applying a magnetic field to the SQUID loop. A tuning range of 750 MHz for a 5 GHz resonator is achieved, and as a figure of merit it can be tuned over 200 line widths. The purpose of the tunable resonators is to use them for dynamic coupling of superconducting quantum bits, this requires that the resonators can be tuned fast on the timescale of the resonator-qubit coupling. To measure tuning speeds faster then the ring up time of the resonators a method that measures the leakage of energy out of a detuned resonator was developed. With this method a frequency shift of the energy stored in the resonator can be measured. A detuning of 330 MHz in less than 10 ns is demonstrated for a 4.5 GHz resonator with a quality factor of 104^44. Working in the few photon limit indicates that the devices can be used to change the frequency of individual photons, this is however still to be demonstrated. As a part of this work the dressed states of a superconducting charge qubit was also studied.
We propose tunable superconducting split-ring resonators (SRRs) employing nonlinear Josephson inductance. A fraction of SRR is replaced by Nb-AlOx-Nb Josephson tunnel junctions connected in parallel and forming a superconducting quantum interference device, whose inductance is sensitive to the external dc magnetic field. Due to the lumped nature of the Josephson inductance, the SRR can be made very compact, and its resonance frequency can be tuned by applying magnetic field. We present the model, results of extensive electromagnetic-simulation and experimental data for the SRR weakly coupled to a transmission line within frequency range of 11–13 GHz.
Josephson microwave circuits are essential for the currently flourishing research on superconducting technologies, such as quantum computation, quantum sensing, and microwave signal processing. To increase the possible parameter space for device operation with respect to the current standards, many materials for superconducting circuits are under active investigation. Here, we present the realization of a frequency-tunable, weakly nonlinear Josephson microwave circuit made of the high-temperature cuprate superconductor YBa2Cu3O7 (YBCO), a material with a high critical temperature and a very high critical magnetic field. An in situ frequency-tunability of ∼300 MHz is achieved by integrating a superconducting quantum interference device (SQUID) into the circuit based on Josephson junctions directly written with a helium ion microscope (HIM). Our results demonstrate that YBCO-HIM-SQUID microwave resonators are promising candidates for quantum sensing and microwave technology applications.
We present a tunable coupler scheme that allows us to tune the coupling strength between a feedline and a superconducting resonator in situ over a wide range. In this scheme, we shunt the feedline with a 50-Ω lumped-element nonlinear transmission line made from a 20 nm NbTiN film. By injecting a DC current, the nonlinear kinetic inductance changes and the effective impedance shunting the resonator periodically varies from a short to an open, which tunes the coupling strength and coupling quality factor Qc. We have demonstrated Qc tuning over a factor of 40, between Qc∼5.5×104 and Qc∼2.3×106, for a 4.5 GHz resonator by applying a DC current less than 3.3 mA. Our tunable coupler scheme is easy to implement and may find broad applications in superconducting detector and quantum computing/information experiments.
Variable microwave-frequency couplers are highly useful components in classical communication systems and likely will play an important role in quantum communication applications. Conventional semiconductor-based microwave couplers have been used with superconducting quantum circuits, enabling, for example, the in situ measurements of multiple devices via a common readout chain. However, the semiconducting elements are lossy and furthermore dissipate energy when switched, making them unsuitable for cryogenic applications requiring rapid, repeated switching. Superconducting Josephson junction-based couplers can be designed for dissipation-free operation with fast switching and are easily integrated with superconducting quantum circuits. These enable on-chip, quantum-coherent routing of microwave photons, providing an appealing alternative to semiconductor switches. Here, we present and characterize a chip-based broadband microwave variable coupler, tunable over 4–8 GHz with over 1.5 GHz instantaneous bandwidth, based on the superconducting quantum interference device with two parallel Josephson junctions. The coupler is dissipation-free and features large on-off ratios in excess of 40 dB, and the coupling can be changed in about 10 ns. The simple design presented here can be readily integrated with superconducting qubit circuits and can be easily generalized to realize a four- or more port device.
Voltage-tunable superconductor-semiconductor devices offer a unique platform to realize dynamic tunability in superconducting quantum circuits. By galvanically connecting a gated InAs\mathrm{In}\mathrm{As}InAs-Al\mathrm{Al}Al Josephson junction to a coplanar waveguide resonator, we demonstrate the use of a superconducting element with wideband gate tunability. We show that the resonant frequency is controlled via a gate-tunable Josephson inductance and that the nonlinearity of the InAs\mathrm{In}\mathrm{As}InAs-Al\mathrm{Al}Al junction is nondissipative as is the case with conventional AlOx-Al{\mathrm{Al}\mathrm{O}}_{\mathrm{x}}\text{-Al}AlOx​-Al junctions. As the gate voltage is decreased, the inductive participation of the junction increases up to $44\mathrm{%}$, resulting in the resonant frequency being tuned by over 2GHz2\phantom{\rule{0.2em}{0ex}}\mathrm{GHz}2GHz. Utilizing the wide tunability of the device, we demonstrate that two resonant modes can be adjusted such that they strongly hybridize, exhibiting an avoided-level crossing with a coupling strength of 51MHz51\phantom{\rule{0.2em}{0ex}}\mathrm{MHz}51MHz. Implementing such voltage-tunable resonators is the first step toward realizing wafer-scale continuous voltage control in superconducting circuits for qubit-qubit coupling, quantum limited amplifiers, and quantum memory platforms.