Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Millimeter, Submillimeter, and Far-Infrared Detectors and Instrumentation for Astronomy XI

Development of an SIS mixer-based amplifier for large-scale multipixel heterodyne receivers

Yoshinori Uzawa, Akira Kawakami, Takafumi Kojima, Kazumasa Makise, Sho Masui, Yosuke Murayama, Akihira Miyachi, Wenlei Shan

Published Aug 16, 2024• 0 citations
Publisher

Abstract

This paper introduces a potential low-power-consumption and low-noise microwave amplifier operated at cryogenic temperature, essential for large-scale multi-pixel heterodyne receivers and fault-tolerant quantum computers. The amplifier employs two millimeter-wave superconductor-insulator-superconductor (SIS) mixers as amplifying elements and a millimeter-wave Josephson array oscillator as the local oscillator source. A proof-of-concept experiment utilizing waveguide SIS mixer modules demonstrated an average gain of approximately 7.5 dB and a noise temperature of around 10 K at microwave frequencies. Additionally, a waveguide Josephson array oscillator module, developed to validate the design, exhibited an output power of roughly 52 nW, estimated from the response of a waveguide SIS detector connected to the oscillator module. These findings indicate the feasibility of realizing a monolithically integrated amplifier chip incorporating SIS mixers and a Josephson array oscillator.

DOI
10.1117/12.3020000

Related papers

Development of an SIS Mixer-Based Low-Noise Amplifier Amenable to Josephson Oscillator Pumping

Yoshinori Uzawa, Takafumi Kojima, Kazumasa Makise +4 more

We propose a low-noise and low-power-consumption microwave amplifier using superconductor-insulator-superconductor (SIS) mixers as quasi-particle frequency up- and down-converters pumped by a Josephson array oscillator in the millimeter-wave band. A proof-of-concept study of an amplifier with two W-band waveguide mixers using Nb/Al-AlOx/Nb junctions in a cascade connection demonstrated an average gain of 6 dB and a noise temperature of 12 K from nearly DC to 5 GHz. We also designed and fabricated a Josephson array oscillator at 100 GHz, which consisted of 31 overdamped Josephson junctions placed at each half-wavelength in an Nb microstrip line. The estimated output power of the oscillator was 0.2 μW at 100 GHz, which can be increased by increasing the number of the oscillator junctions. These results suggest that the proposed SIS mixer-based amplifier is suitable for on-chip integrated circuits to be implemented in large-scale multipixel SIS receivers and quantum computers.

IEEE Transactions on Applied Superconductivity•Mar 8, 2023•5 citations

Fabrication and Evaluation of Waveguide Josephson Array Oscillators at Millimeter-Wave Lengths for SIS Mixer-Based Amplifiers

Yosuke Murayama, Akira Kawakami, Wenlei Shan +5 more

In this study, a 150 GHz waveguide Josephson array oscillator was designed, fabricated, and evaluated as a local oscillator (LO) source for superconductor-insulator-superconductor (SIS) mixer-based amplifiers. These amplifiers aim to reduce the power consumption of microwave amplifiers used in large-scale multi-pixel heterodyne receivers for radio astronomy and superconducting quantum computers. We fabricated a Josephson array oscillator of 11 Nb/Al–AlOx/Nb Josephson junctions with Cu shunt resistors, each of which is placed on the center of a half-wavelength microstrip line resonator. When the LO signal from the oscillator was introduced into the balanced SIS mixers via a waveguide, the oscillator successfully pumped four SIS mixers simultaneously, delivering a total estimated LO power of 0.22 µW at 146.7 GHz. The SIS mixers operated without a millimeter-wave isolator at an LO noise temperature of 4–6 K. These results indicate the Josephson array oscillator's potential as an LO source for SIS mixer-based amplifiers.

IEEE Transactions on Applied Superconductivity•Dec 12, 2024•3 citations

An SIS-mixer-based amplifier for multi-pixel heterodyne receivers

Yoshinori Uzawa, Takafumi Kojima, Yuto Kozuki +5 more

We are investigating a possible microwave amplifier with low noise and low power consumption at cryogenic temperature for large scale multi-pixel heterodyne superconductor-insulator-superconductor (SIS) receivers at millimeter and submillimeter wavelengths. We propose the use of SIS junctions as amplifier elements based on quasi-particle mixing. By connecting an SIS up-converter and an SIS down-converter in series with gain in both converters, a lownoise and low-power-consumption high-frequency amplifier can be obtained in principle. A proof-of-concept study has been made by configuring an amplifier with two Nb/Al-AlOx/Nb mixers in the 150-GHz band in a standard noise and gain measurement setup at 4 K with a microwave noise source as an input signal. We observed a maximum gain of more than 10 dB and a minimum noise temperature of less than 10 K, which suggests that our proposed SIS amplifier is capable for multi-pixel SIS receivers. On the other hand, we also observed a periodical behavior in frequency dependence of the measured noise temperature and gain due to a standing-wave effect between the two SIS mixers, which is a problem to be solved.

Millimeter, Submillimeter, and Far-Infrared Detectors and Instrumentation for Astronomy XI•Dec 12, 2020•8 citations

Development of a Waveguide Josephson Oscillator for SIS Mixer-Based Amplifiers

Yoshinori Uzawa, Akira Kawakami, Takafumi Kojima +6 more

A waveguide Josephson array oscillator operating at a frequency of 100 GHz was designed and fabricated to evaluate its pumping capability as a local oscillator (LO) for our proposed SIS mixer-based amplifier, which incorporates SIS up- and down-converters. The LO power requirement was estimated by simulation to be several nanowatts when the SIS up-converter is optimized for noise temperature and conversion gain under the condition that the input port at the microwave frequencies is connected to a practical 50-W system. The fabricated waveguide Josephson array oscillator module has 31 Nb Josephson junctions placed at the center of a half-wavelength resonator of an Nb microstripline. The output power from the waveguide oscillator module was evaluated by connecting it to the waveguide SIS detector module in a 4-K cryostat. Photon-assisted tunneling steps were clearly observed, from which the detected power was estimated to be approximately 17 nW at 106 GHz. These results suggest that the Josephson array oscillator is capable of being used in the SIS mixer-based amplifier as the LO.

IEEE Transactions on Applied Superconductivity•Jan 26, 2024•3 citations

Characterization of a low-noise superconductor–insulator–superconductor-based microwave amplifier with local oscillator phase-adjusting architecture

Takafumi Kojima, Sho Masui, Wenlei Shan +1 more

This paper describes a low-noise microwave amplifier based on up- and down-frequency-conversion processes in quasiparticle superconductor–insulator–superconductor (SIS) tunnel junctions. The SIS amplifier was configured with two SIS frequency-converter modules and a cryogenic millimeter-wave isolator inserted between them. Moreover, a local oscillator (LO) using millimeter-wave attenuators and a phase shifter was considered. This setup allowed the control of individual LO power and differential phase in these SIS frequency converters to optimize the amplifier performance. The SIS amplifier showed noise temperatures as low as 11 K and a 6–8 dB gain from nearly DC to 5 GHz. The attained microwave performance is promising for obtaining large-format arrays, such as multibeam heterodyne receivers. Moreover, this two-frequency-converter concept based on SIS junctions might enable microwave applications, such as wideband non-reciprocal circuits in isolators, gyrators, and circulators, which are essential devices in the quantum computing and radio astronomy fields.

Applied Physics Letters•Feb 13, 2023•9 citations

Low-noise integrated balanced SIS mixer for 787–950 GHz

Yasunori Fujii, Takafumi Kojima, Álvaro González +5 more

Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.

Superconductor Science and Technology•Nov 30, 2016•13 citations
This paper introduces a potential low-power-consumption and low-noise microwave amplifier operated at cryogenic temperature, essential for large-scale multi-pixel heterodyne receivers and fault-tolerant quantum computers. The amplifier employs two millimeter-wave superconductor-insulator-superconductor (SIS) mixers as amplifying elements and a millimeter-wave Josephson array oscillator as the local oscillator source. A proof-of-concept experiment utilizing waveguide SIS mixer modules demonstrated an average gain of approximately 7.5 dB and a noise temperature of around 10 K at microwave frequencies. Additionally, a waveguide Josephson array oscillator module, developed to validate the design, exhibited an output power of roughly 52 nW, estimated from the response of a waveguide SIS detector connected to the oscillator module. These findings indicate the feasibility of realizing a monolithically integrated amplifier chip incorporating SIS mixers and a Josephson array oscillator.
We propose a low-noise and low-power-consumption microwave amplifier using superconductor-insulator-superconductor (SIS) mixers as quasi-particle frequency up- and down-converters pumped by a Josephson array oscillator in the millimeter-wave band. A proof-of-concept study of an amplifier with two W-band waveguide mixers using Nb/Al-AlOx/Nb junctions in a cascade connection demonstrated an average gain of 6 dB and a noise temperature of 12 K from nearly DC to 5 GHz. We also designed and fabricated a Josephson array oscillator at 100 GHz, which consisted of 31 overdamped Josephson junctions placed at each half-wavelength in an Nb microstrip line. The estimated output power of the oscillator was 0.2 μW at 100 GHz, which can be increased by increasing the number of the oscillator junctions. These results suggest that the proposed SIS mixer-based amplifier is suitable for on-chip integrated circuits to be implemented in large-scale multipixel SIS receivers and quantum computers.
In this study, a 150 GHz waveguide Josephson array oscillator was designed, fabricated, and evaluated as a local oscillator (LO) source for superconductor-insulator-superconductor (SIS) mixer-based amplifiers. These amplifiers aim to reduce the power consumption of microwave amplifiers used in large-scale multi-pixel heterodyne receivers for radio astronomy and superconducting quantum computers. We fabricated a Josephson array oscillator of 11 Nb/Al–AlOx/Nb Josephson junctions with Cu shunt resistors, each of which is placed on the center of a half-wavelength microstrip line resonator. When the LO signal from the oscillator was introduced into the balanced SIS mixers via a waveguide, the oscillator successfully pumped four SIS mixers simultaneously, delivering a total estimated LO power of 0.22 µW at 146.7 GHz. The SIS mixers operated without a millimeter-wave isolator at an LO noise temperature of 4–6 K. These results indicate the Josephson array oscillator's potential as an LO source for SIS mixer-based amplifiers.
We are investigating a possible microwave amplifier with low noise and low power consumption at cryogenic temperature for large scale multi-pixel heterodyne superconductor-insulator-superconductor (SIS) receivers at millimeter and submillimeter wavelengths. We propose the use of SIS junctions as amplifier elements based on quasi-particle mixing. By connecting an SIS up-converter and an SIS down-converter in series with gain in both converters, a lownoise and low-power-consumption high-frequency amplifier can be obtained in principle. A proof-of-concept study has been made by configuring an amplifier with two Nb/Al-AlOx/Nb mixers in the 150-GHz band in a standard noise and gain measurement setup at 4 K with a microwave noise source as an input signal. We observed a maximum gain of more than 10 dB and a minimum noise temperature of less than 10 K, which suggests that our proposed SIS amplifier is capable for multi-pixel SIS receivers. On the other hand, we also observed a periodical behavior in frequency dependence of the measured noise temperature and gain due to a standing-wave effect between the two SIS mixers, which is a problem to be solved.
A waveguide Josephson array oscillator operating at a frequency of 100 GHz was designed and fabricated to evaluate its pumping capability as a local oscillator (LO) for our proposed SIS mixer-based amplifier, which incorporates SIS up- and down-converters. The LO power requirement was estimated by simulation to be several nanowatts when the SIS up-converter is optimized for noise temperature and conversion gain under the condition that the input port at the microwave frequencies is connected to a practical 50-W system. The fabricated waveguide Josephson array oscillator module has 31 Nb Josephson junctions placed at the center of a half-wavelength resonator of an Nb microstripline. The output power from the waveguide oscillator module was evaluated by connecting it to the waveguide SIS detector module in a 4-K cryostat. Photon-assisted tunneling steps were clearly observed, from which the detected power was estimated to be approximately 17 nW at 106 GHz. These results suggest that the Josephson array oscillator is capable of being used in the SIS mixer-based amplifier as the LO.
This paper describes a low-noise microwave amplifier based on up- and down-frequency-conversion processes in quasiparticle superconductor–insulator–superconductor (SIS) tunnel junctions. The SIS amplifier was configured with two SIS frequency-converter modules and a cryogenic millimeter-wave isolator inserted between them. Moreover, a local oscillator (LO) using millimeter-wave attenuators and a phase shifter was considered. This setup allowed the control of individual LO power and differential phase in these SIS frequency converters to optimize the amplifier performance. The SIS amplifier showed noise temperatures as low as 11 K and a 6–8 dB gain from nearly DC to 5 GHz. The attained microwave performance is promising for obtaining large-format arrays, such as multibeam heterodyne receivers. Moreover, this two-frequency-converter concept based on SIS junctions might enable microwave applications, such as wideband non-reciprocal circuits in isolators, gyrators, and circulators, which are essential devices in the quantum computing and radio astronomy fields.
Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.