Superconducting transmon qubits have seen significant progress in the last five years. By optimizing and exploring different fabrication process and superconducting material, transmon lifetime is more than 100 us with single-qubit gate and two-qubit gate fidelity is higher than to 99.8%. This thesis reports work to realize a transmon qubit fabrication process and experiment test bed. The experiment stage at the mixing chamber of the dilution fridge is designed and the microwave setup for qubit control and characterization is demonstrated. The qubit fabrication recipe using aluminum and Al/AlOx/Al junction is developed and measured. The qubit lifetime reach an average of 10 us and single-qubit gate fidelity is F = 99.883 +- 0.007%. While the parameters are moderate compared to the state of the art, this system is a good stepping stone to explore qubit scaling and optimization.
Superconducting transmon qubits have seen significant progress in the last five years. By optimizing and exploring different fabrication process and superconducting material, transmon lifetime is more than 100 us with single-qubit gate and two-qubit gate fidelity is higher than to 99.8%. This thesis reports work to realize a transmon qubit fabrication process and experiment test bed. The experiment stage at the mixing chamber of the dilution fridge is designed and the microwave setup for qubit control and characterization is demonstrated. The qubit fabrication recipe using aluminum and Al/AlOx/Al junction is developed and measured. The qubit lifetime reach an average of 10 us and single-qubit gate fidelity is F = 99.883 +- 0.007%. While the parameters are moderate compared to the state of the art, this system is a good stepping stone to explore qubit scaling and optimization.
This thesis mainly summarizes two experiments that relate to building a quantum computer out of superconducting transmon qubits. Transmon qubits have emerged as one of the foremost solid state qubits, realizing processors with more than ten qubits and demonstrating small scale quantum algorithms as well as quantum error correction schemes. Right now, there is a race between different academic and industry research groups to scale up transmon qubit processors. The first experiment was a demonstration of qubit control by selective broadcasting in order to reduce the scaling of expensive electronics with the number of qubits for individual single-qubit control. We demonstrated that we can bring two transmon qubits to the same frequency (combining fabrication accuracy and in-situ fine tuning) and use the same hardware to control both, routing the pulses with a nanosecond-timescale vector switch matrix. Despite the compromises required by this technique, we show a scalable path to single qubit control beyond the threshold required for quantum error correction. In benchmarking, we take into account gate leakage due to the fact that transmons are fundamentally multi-level systems. In the second experiment we establish entanglement between two transmon qubits on different chips. We use an entanglement by measurement scheme and demonstrate that we can overcome minor fabrication imperfections by shaping our measurement pulses. Ultimately, performance is mainly limited by photon loss between the chips and up to the amplification chain. This entanglement mediated by traveling photons could be used to make a distributed transmon processor where computations are spread across several chip modules. This modularity could enable connectivities that cannot be realized on chip and ease fabrication requirements, as modules could be individually fabricated and selected. Thus, both of these experiments fit into the larger effort to converge on the hardware, control equipment and architecture of a future large-scale transmon quantum computer. Other experiments I contributed to are summarized in the conclusion chapter to show the diverse physics that can be studied in cQED experiments.
Superconducting qubits are a promising technology for building a scalable quantum computer. An important architecture employed in the field is called Circuit Quantum Electrodynamics (circuit QED), where such qubits are combined with high quality microwave cavities to study the interaction between artificial atoms and single microwave photons. The ultra-strong coupling achieved in these systems allows for control and readout of the quantum state of qubits to perform quantum information processing. The work on circuit QED performed in this thesis consisted of realizing an experimental setup for qubit experiments in a new laboratory, investigating the coherence and decay of higher energy levels of superconducting transmon qubits and finally demonstrating a novel coaxial form of circuit QED. Designing and building a 3D circuit QED setup involved the following main accomplishments: producing high quality 3D cavities; designing and installing the cryogenic microwave setup as well as the room temperature amplification and data acquisition circuitry; successfully developing a recipe for the fabrication of Josephson junctions; controlling and measuring superconducting 3D transmon qubits at 10mK. Several qubits were fully characterised and have shown coherence times of several microseconds and relaxation times up to 25μs. Superconducting qubits in fact possess higher energy levels that can provide significant computational advantages in quantum information applications. In experiments performed at MIT, preparation and control of the five lowest states of a transmon qubit was demonstrated, followed by an investigation of the phase coherence and decay dynamics of these higher energy levels. The decay was found to proceed mainly sequentially with relaxation times in excess of 20μs for all transitions. A direct measurement of the charge dispersion of these levels was performed to explore their characteristics of dephasing. This experiment was also reproduced on a 3D transmon fabricated and measured in Oxford, where due to a higher effective qubit temperature a multi-level decay model including thermal excitations was developed to explain the observed relaxation dynamics. Finally, a coaxial transmon, which we name the coaxmon, is presented and measured with a coaxial LC readout resonator and input/output coupling ports placed inline along the third dimension. This novel coaxial circuit QED architecture holds great promise for developing a scalable planar grid of qubits to build a quantum computer.
The strong requirement for high-performing quantum computing led to intensive research on novel quantum platforms in the last decades. The circuital nature of Josephson-based quantum superconducting systems powerfully supports massive circuital freedom, which allowed for the implementation of a wide range of qubit designs, and an easy interface with the quantum processing unit. However, this unavoidably introduces a coupling with the environment, and thus to extra decoherence sources. Moreover, at the time of writing, control and readout protocols mainly use analogue microwave electronics, which limit the otherwise reasonable scalability in superconducting quantum circuits. Within the future perspective to improve scalability by integrating novel control energy-efficient superconducting electronics at the quantum stage in a multi-chip module, we report on an all-microwave characterization of a planar two-transmon qubits device, which involves state-of-the-art control pulses optimization. We demonstrate that the single-qubit average gate fidelity is mainly limited by the gate pulse duration and the quality of the optimization, and thus does not preclude the integration in novel hybrid quantum-classical superconducting devices.
The superconducting transmon qubit is a leading platform for quantum computing and quantum science. Building large, useful quantum systems based on transmon qubits will require significant improvements in qubit relaxation and coherence times, which are orders of magnitude shorter than limits imposed by bulk properties of the constituent materials. This indicates that relaxation likely originates from uncontrolled surfaces, interfaces, and contaminants. Previous efforts to improve qubit lifetimes have focused primarily on designs that minimize contributions from surfaces. However, significant improvements in the lifetime of two-dimensional transmon qubits have remained elusive for several years. Here, we fabricate two-dimensional transmon qubits that have both lifetimes and coherence times with dynamical decoupling exceeding 0.3 milliseconds by replacing niobium with tantalum in the device. We have observed increased lifetimes for seventeen devices, indicating that these material improvements are robust, paving the way for higher gate fidelities in multi-qubit processors.
Abstract Here we report a breakthrough in the fabrication of a long lifetime transmon qubit. We use tantalum films as the base superconductor. By using a dry etching process, we obtained transmon qubits with a best T1 lifetime of 503 μs. As a comparison, we also fabricated transmon qubits with other popular materials, including niobium and aluminum, under the same design and fabrication processes. After characterizing their coherence properties, we found that qubits prepared with tantalum films have the best performance. Since the dry etching process is stable and highly anisotropic, it is much more suitable for fabricating complex scalable quantum circuits, when compared to wet etching. As a result, the current breakthrough indicates that the dry etching process of tantalum film is a promising approach to fabricate medium- or large-scale superconducting quantum circuits with a much longer lifetime, meeting the requirements for building practical quantum computers.
Compared to traditional semiconductor control electronics (TSCE) located at room temperature, cryogenic single flux quantum (SFQ) electronics can provide qubit measurement and control alternatives that address critical issues related to scalability of cryogenic quantum processors. Single-qubit control and readout have been demonstrated recently using SFQ circuits coupled to superconducting qubits. Experiments where the SFQ electronics are co-located with the qubit have suffered from excess decoherence and loss due to quasiparticle poisoning of the qubit. A previous experiment by our group showed that moving the control electronics to the 3 K stage of the dilution refrigerator avoided this source of decoherence in a high-coherence 3D transmon geometry. In this paper, we also generate the pulses at the 3 K stage but have optimized the qubit design and control lines for scalable 2D transmon devices. We directly compare the qubit lifetime T1, coherence time T2∗ and gate fidelity when the qubit is controlled by the Josephson pulse generator (JPG) circuit versus the TSCE setup. We find agreement to within the daily fluctuations for T1 and T2∗, and agreement to within 10% for randomized benchmarking. We also performed interleaved randomized benchmarking on individual JPG gates demonstrating an average error per gate of 0.46% showing good agreement with what is expected based on the qubit coherence and higher-state leakage. These results are an order of magnitude improvement in gate fidelity over our previous work and demonstrate that a Josephson microwave source operated at 3 K is a promising component for scalable qubit control.