We have designed a traveling-wave parametric amplifier based on quantum phase-slip junctions. This amplifier has a LC-ladder nonlinear transmission line structure, and acts as a dual to the Josephson traveling-wave parametric amplifier. We use WRspice simulations to design and analyze the quantum phase-slip junction-based traveling-wave parametric amplifier. Our simulations capture parametric amplification by demonstrating frequency mixing, signal gain, and generation of an idler tone. In additional simulations, we control various circuit parameters: the quantum phase-slip junctions, critical voltage, quantum phase-slip junction count, and bias voltage. We report and discuss these parameters' effects on the amplifier's signal gain. We compare these performance metrics with those from simulations of a typical Josephson traveling-wave parametric amplifier.
We have designed a traveling-wave parametric amplifier based on quantum phase-slip junctions. This amplifier has a LC-ladder nonlinear transmission line structure, and acts as a dual to the Josephson traveling-wave parametric amplifier. We use WRspice simulations to design and analyze the quantum phase-slip junction-based traveling-wave parametric amplifier. Our simulations capture parametric amplification by demonstrating frequency mixing, signal gain, and generation of an idler tone. In additional simulations, we control various circuit parameters: the quantum phase-slip junctions, critical voltage, quantum phase-slip junction count, and bias voltage. We report and discuss these parameters' effects on the amplifier's signal gain. We compare these performance metrics with those from simulations of a typical Josephson traveling-wave parametric amplifier.
The development of large-scale superconducting quantum computers critically depends on the accurate readout of qubit states. To enable this, cryogenic parametric amplifiers have been proposed and developed, and have since found widespread use in small-signal detection applications. Among various amplifier architectures, Josephson traveling-wave parametric amplifiers (JTWPAs) are widely adopted due to their broad bandwidth, high saturation power, and compatibility with superconducting qubits. In this work, we present a design workflow of JTWPAs based on a co-simulation approach combining electromagnetic (EM) and circuit-level simulation. We apply this method to a uniform JTWPA, comparing our simulation results with experimental data. To mitigate the challenge of constructing lumped element circuit models usually used in conventional simulation method, we directly perform full EM analysis of the device to accurately determine its linear response. The extracted S parameters are then fed into a nonlinear harmonic balance simulator with Josephson junctions modeled as circuit elements. By doing so, the linear and gain properties of the JTWPA are extracted. Different factors that impact device performance including gain compression, phase matching, and fabrication imperfections are further investigated and modeled. A good agreement between simulation and measurements is identified, establishing the effectiveness of our approach in designing quantum parametric amplifiers.
We develop a concept of traveling-wave Josephson parametric amplifier based on a ladder-type superconducting transmission line containing serial array of one-junctions SQUIDs. The circuit operates in a three-wave mixing mode and exploits both quadratic and cubic (Kerr) nonlinearities in the current-phase relation of the SQUIDs controlled by external magnetic flux. These two types of nonlinearities allow efficient three-wave mixing and perfect phase matching, respectively. The transmission line exhibits a power gain with exponential dependence on its length (number of cells N) in the widest frequency range, 0≲fs,fi≲fp, where fs, fi and fp are the signal, idler and pump frequencies, respectively, obeying relation fs+fi=fp. Estimation of the amplifier characteristics with typical experimental parameters, number of cells N = 700, length of 28 mm and pump frequency of 12.5 GHz yields a flat (-3 dB) gain of about 20 dB in the bandwidth from 3.35 GHz to 9.15 GHz and a saturation power of -90 dBm.
High gain and large bandwidth of traveling-wave parametric amplifier exploiting the nonlinearity of Josephson Junctions can be achieved by fulfilling the so-called phase-matching condition. This condition is usually addressed by placing resonant structures along the waveguide or by periodic modulations of its parameters, creating gaps in the waveguide’s dispersion. Here, we propose to employ the Josephson junctions, which constitute the centerline of the amplifier, as resonant elements for phase matching. By numerical simulations in JoSIM (and WRspice) software, we show that Josephson plasma oscillations can be utilized to create wave vector mismatch sufficient for phase matching as well as to prevent the conversion of the pump energy to higher harmonics. The proposed traveling wave parametric amplifier design has a gain of 15 dB and a 3 GHz bandwidth, which is comparable to the state-of-the-art TWPAs.
Josephson parametric amplifiers have become a critical tool in superconducting device physics due to their high gain and quantum-limited noise. Traveling wave parametric amplifiers (TWPAs) promise similar noise performance, while allowing for significant increases in both bandwidth and dynamic range. We present a TWPA device based on an LC-ladder transmission line of Josephson junctions and parallel plate capacitors using low-loss amorphous silicon dielectric. Crucially, we have inserted λ/4 resonators at regular intervals along the transmission line in order to maintain the phase matching condition between pump, signal, and idler and increase gain. We achieve an average gain of 12 dB across a 4 GHz span, along with an average saturation power of −92 dBm with noise approaching the quantum limit.
Abstract A Josephson traveling-wave parametric amplifier (JTWPA) is indispensable for the high-fidelity readout of superconducting qubits, owing to its broadband gain and near-quantum-limited noise performance. Conventional JTWPAs implemented with 0-Josephson junctions (0-JTWPAs) avoid magnetic-flux bias but rely on Kerr nonlinearity, which leads to pump-power-dependent phase mismatch, gain ripple, and a limited dynamic range. More recently, three-wave-mixing (3WM) JTWPAs employing flux-biased rf-SQUIDs have been proposed to suppress Kerr effects. However, these designs require a significant external flux bias per unit cell, which complicates cryogenic hardware, introduces sensitivity to flux noise, and limits scalability in large arrays. In this study, we propose and analyze a π -junction-based JTWPA ( π -JTWPA) in which the intrinsic π phase shift of the junction effectively displaces the operating point of the current–phase relation. This approach aims to realize 3WM-type nonlinearity with reduced flux bias while preserving broadband amplification, thereby simplifying flux-bias distribution, enhancing robustness against flux noise, and providing a pathway toward scalable, multiplexed quantum readout architectures. In addition, we examine the potential applicability of the π -JTWPA in four-wave-mixing (4WM) operation.
In this contribution, we investigate different types of Josephson junction arrays that are embedded in coplanar microwave transmission lines, acting as traveling-wave parametric amplifiers. For the realization of traveling-wave parametric amplifiers, different Josephson junction array geometries have been proposed in the literature. Here, we investigate the amplifier’s Josephson nonlinearity along with the gain performance, following a general method to derive the nonlinear wave-mixing coefficients from the current-phase relation of different junction array topologies. These nonlinear coefficients are then incorporated into a corresponding Hamiltonian, which is used in order to solve the Heisenberg equations of motion of the photon number operator, determining the gain of the amplifier.