Argentine Conference on Electronics (CAE)

Towards a Low-Cost Readout System for Arrays of Cryogenic Detectors

K. J. Ramos, Horacio Arnaldi, L. Tosi

Published Mar 9, 2023• 1 citation

Abstract

A microwave kinetic inductance detector (MKID) is a superconducting pair-breaking detector used for astronomical observations in the sub-millimeter through visible range. Radiation is detected as a phase and amplitude signal proportional to the frequency shift of the device. In the case of arrays of MKIDs, the read-out is performed using the frequency division multiplexing technique. However, there is currently no commercial system or low-cost standard electronics available for this task. In this work, we take the first steps towards developing a low-cost readout system for MKIDs based on the Red Pitaya board. We have developed a firmware for the efficient generation of probe tones, and show figures of merit characterizing the performance of the readout in a hardware prototype. The design is flexible, letting us to adapt it to new frequencies and amplitudes requirements of the MKID arrays.

DOI: 10.1109/cae56623.2023.10086976

Related papers

Modeling and Simulation of Microwave Kinetic Inductance Detector Readout System Using Simulink and RF Blockset

Taehoon Kim

Microwave kinetic inductance detectors (MKIDs) represent a class of low-temperature superconducting detectors employed for observing astronomical phenomena spanning the submillimeter through visible bands. Renowned for their intrinsic frequency-division multiplexing capability at microwave frequencies, MKIDs offer the advantage of eliminating the need for complex cryogenic multiplexing electronics. However, the overall readout architecture remains complex, necessitating sophisticated room-temperature electronics. Optimizing overall performance poses a significant challenge. This article introduces a novel approach to behavioral modeling and simulation for the MKID readout system utilizing Simulink and the RF Blockset library. The models incorporate major nonidealities of electronic components to investigate their impacts on system performance. In addition, the model of the MKID array is included based on measured transmission data, ensuring high simulation accuracy. The simulation tool facilitates the study and high-level design of the MKID readout system before delving into hardware implementation.

IEEE Transactions on Applied SuperconductivityMar 4, 20252 citations

RF/IF hardware design for MKIDs application

Alikhan Talipbayev

This report covers work done at Data Processing and Readout System Development Laboratory at Nazarbayev University implementing data processing algorithm for readout electronics. Microwave Kinetic Inductance Detectors (MKIDs) are photon detectors based on superconducting resonators. MKIDs are capable of detecting single photons with very small energy and micro second time resolutions. With proper readout electronic system it is possible to read arrays of thousands MKIDs using single signal line using frequency domain multiplexing (FDM). This report details the work done developing a laboratory setup for measuring MKIDs and developing code for frequency measurements. All the work was done using readout system based on a Re-configurable Open Archite Computing Hardware (ROACH) FPGA board and The Collaboration for Astronomy Signal Processing and Electronics Research (CASPER) software.

Apr 27, 20240 citations

HARDWARE IMPLEMENTATION OF AN EFFICIENT FREQUENCY COMB GENERATOR FOR MICROWAVE KINETIC INDUCTANCE DETECTORS

Frank Danso

The frequency comb generator is an essential component in the readout of superconducting detectors. This component is responsible for generating the resonant frequencies necessary to detect photon interaction with the detectors. This component however has not received the much needed attention in terms of readout systems optimization. Conventional implementations rely on either inverse fast Fourier transform (IFFT) engines, which scale poorly in power with increasing frequency resolution requirement but allow flexible tone updates, or lookup tables (LUTs), which demand large memory for high frequency resolution. Microwave Kinetic Inductance Detectors (MKIDs) are superconducting detectors which have gained significant interest for cryogenic astrophysical instrumentation due to their high sensitivity, intrinsic multiplexing capability, and scalable fabrication. However, their simplified detector architecture shifts complexity to the readout electronics, making the development of compact, low-power frequency comb generators especially valuable. The design of the compact frequency comb generator targets applications involving MKIDs which typically detect photons in the submilliter bands. In this thesis, I present the design and hardware realization of a compact frequency comb generator. The design has been verified on an Field Programmable Gate Array (FPGA) using the Xilinx's RFSoC ZCU111 evaluation board. The architecture consumes less than 5% of FPGA resources and less than 5 Watts of power with the capability of handling multiple independent channels of the compact frequency comb generator on the evaluation board. These results demonstrate the potential of this approach to enable scalable, energy-efficient MKID readout systems for large-format detector arrays in next-generation cryogenic experiments.

Jan 1, 20250 citations

Crest factor optimization of multi-tone signals generated for low-temperature sensor readout

Horacio Arnaldi

Microwave kinetic inductance detectors (MKID) are a growing technology of cryogenic detectors and have a great potential in radio-astronomy and cosmic microwave background (CMB) characterization. A review of the general readout performance requirements for experiments requiring the multiplexing of large arrays (~10.000 pixels) of such cryogenic detectors is presented. The focus is on the crest factor optimization process for proper excitation and readout of these large arrays of detectors. It is shown an algorithm to optimize the phase generation of the carriers to obtain a low crest factor, favoring the dynamic range usage of the electronic chain.

Argentine Conference on Electronics (CAE)Mar 9, 20232 citations

Design and Readout of Large MKID Arrays for Submillimeter Astronomy

James A. Schlaerth, Omid Noroozian, Nicole G. Czakon +16 more

Microwave Kinetic Inductance Detectors (MKIDs) are superconducting microresonators useful as detectors for sub/millimeter and far-infrared cameras, as well as instruments in optical and x-ray wavelengths. A probe sine wave at the resonance frequency can detect a change in frequency and microwave loss due to submillimeter optical load as a phase or amplitude change. These detectors may be coupled to light through on-chip, phased-array antennas. A single antenna may feed several detectors with different bandpasses defined by on-chip lumped-element filters. The resonators are easily frequency multiplexed by tuning the resonance frequencies, so hundreds of detectors can be read out while coupled to a single feedline. The deployment and operation of ground-based, background-limited detectors in close-packed arrays present significant challenges in both readout strategy and array design. The initial designs consisted of simple coplanar waveguide microwave resonators with aluminum absorptive sections. The first change has been to substitute the capacitive portion of the resonator with a large interdigitated capacitor (IDC) to reduce its noise contribution. While their low-noise characteristics have been demonstrated, these detectors had not yet been tested on array-scale devices. We present results from arrays of detectors designed for sub/millimeter imaging, tested for their optical response characteristics. In particular, we address challenges of microwave inter-resonator coupling, out-of-band resonator optical sensitivity, and noise reduction in the latest device designs. We show the results of stepped-impedance filters in preventing direct pickup of wide-band radiation, and new frequency spacing to limit crosstalk between resonators. We show direct comparison between olderdesign coplanar waveguide resonators and new IDC resonators under optical load, demonstrating the noise reduction and comparable responsivity. In addition, we show results of the probe signal readout power that maximizes signal-to-noise.

Softwaretechnik-TrendsMar 1, 20100 citations

Superconducting Microwave Resonator Arrays for Submillimeter/Far-infrared Imaging

Omid Noroozian

Superconducting microwave resonators have the potential to revolutionize submillimeter and far-infrared astronomy, and with it our understanding of the universe. The field of low-temperature detector technology has reached a point where extremely sensitive devices like transition-edge sensors are now capable of detecting radiation limited by the background noise of the universe. However, the size of these detector arrays are limited to only a few thousand pixels. This is because of the cost and complexity of fabricating large-scale arrays of these detectors that can reach up to 10 lithographic levels on chip, and the complicated SQUID-based multiplexing circuitry and wiring for readout of each detector. In order to make substantial progress, next- generation ground-based telescopes such as CCAT or future space telescopes require focal planes with large-scale detector arrays of 104–106 pixels. Arrays using microwave kinetic inductance detectors (MKID) are a potential solution. These arrays can be easily made with a single layer of superconducting metal film deposited on a silicon substrate and pattered using conventional optical lithography. Furthermore, MKIDs are inherently multiplexable in the frequency domain, allowing ∼ 103 detectors to be read out using a single coaxial transmission line and cryogenic amplifier, drastically reducing cost and complexity. An MKID uses the change in the microwave surface impedance of a superconducting thin-film microresonator to detect photons. Absorption of photons in the superconductor breaks Cooper pairs into quasiparticles, changing the complex surface impedance, which results in a perturbation of resonator frequency and quality factor. For excitation and readout, the resonator is weakly coupled to a transmission line. The complex amplitude of a microwave probe signal tuned on-resonance and transmitted on the feedline past the resonator is perturbed as photons are absorbed in the superconductor. The perturbation can be detected using a cryogenic amplifier and subsequent homodyne mixing at room temperature. In an array of MKIDs, all the resonators are coupled to a shared feedline and are tuned to slightly different frequencies. They can be read out simultaneously using a comb of frequencies generated and measured using digital techniques. This thesis documents an effort to demonstrate the basic operation of ∼ 256 pixel arrays of lumped-element MKIDs made from superconducting TiNx on silicon. The resonators are designed and simulated for optimum operation. Various properties of the resonators and arrays are measured and compared to theoretical expectations. A particularly exciting observation is the extremely high quality factors (∼ 3 × 107) of our TiNx resonators which is essential for ultra-high sensitivity. The arrays are tightly packed both in space and in frequency which is desirable for larger full-size arrays. However, this can cause a serious problem in terms of microwave crosstalk between neighboring pixels. We show that by properly designing the resonator geometry, crosstalk can be eliminated; this is supported by our measurement results. We also tackle the problem of excess frequency noise in MKIDs. Intrinsic noise in the form of an excess resonance frequency jitter exists in planar superconducting resonators that are made on dielectric substrates. We conclusively show that this noise is due to fluctuations of the resonator capacitance. In turn, the capacitance fluctuations are thought to be driven by two-level system (TLS) fluctuators in a thin layer on the surface of the device. With a modified resonator design we demonstrate with measurements that this noise can be substantially reduced. An optimized version of this resonator was designed for the multiwavelength submillimeter kinetic inductance camera (MUSIC) instrument for the Caltech Submillimeter Observatory.

Jun 12, 201211 citations